5” STRAIGHT KNIFE INSTRUCTION MANUAL
5000FS
1
5000FS
INSTRUCTION MANUAL
2
RELIABLE. RIGHT THERE WITH YOU.
At Reliable, we do what we love, and take pride in doing it right.
You want what’s best for the people, places and things that matter
in your life – from where you live to what you wear. So do we. From
the start, we approach every product with a craftsman’s attention
to detail and passion for making it right. Quality, functionality,
design and customer service play an equally important part in
delivering what’s right for you. The 5000FS is the ideal choice for
cutting jobs that require a straight knife, but where the height of
the lay is less then 5”.
For your safety and to fully enjoy the advantages of this product,
please take a few minutes to read all the important safeguards
and care instructions. Keep this manual handy and review the
product warranty for your reference.
3
IMPORTANT SAFETY REQUIREMENTS
BEFORE OPERATION
1. Fill oil cup, and ensure oil is inserted smoothly.
2. Push in and turn the machine by hand for a few revolutions to ensure that the oil is
spread over all of the contact surfaces.
3. The sharpener must always be placed up in the locked position before starting.
CAUTION
a. Keep the machine in a warm environment during cold weather.
b. Turn the machine on and off briefly before running the machine continuously. This helps
prevent excess friction between contact surfaces.
c. Do not use excess oil. Only use grade NO. 30 motor oil.
SHARPENER OPERATION
1. Place the machine away from piles of material.
2. Drop the pressure foot lever located next to the operating handle.
3. Press the lever downward slowly, using firm pressure.
CAUTION
a. Do not operate sharpener without the knife in the machine.
b. Do not operate sharpener with cutting material laid in the machine.
c. Do not shut off motor while sharpener is in motion.
d. If the lever is locked in halfway, lift the lever to unlock and start again.
CARE
1. Clean lint out of the motor and sharpener twice a week.
2. Lint around screw mechanism of sharpener inside the cover must be cleaned once a
week.
3. Clean the knife slide by the slot cleaner once a day.
4. Remove lint from rollers in the base plate. To prevent accumulation of lint, do not oil
plate rollers. If rollers stick, remove them from the plate and wash in a cleaning solvent.
4
Capacittor-Strator
Carrying Handle Screws
Rotor Fan
Rotor with Shaft
Cut-Out Switch to Bearing Screw Dust Cap Screw
Dust Cap Screw
Rear Bearing Housing
Dust Cap
Turning Knob
Cut-Out Switch
Insulated Plate
Insulated Cover
Set Screw for Insulated Cover
Automatic Cut-Out
Front to Rear Bearing Screw
KD-1
KD-2
KD-3
KD-4
KD-5
KD-6
KD-7
KD-8
KD-9
KD-10
KD-10P
KD-10C
KD-10CS
KD-12
KD-14
KD-15
KD-16
KD-17
KD-18
KD-18P
KD-20
KD-21
KD-22
KD-23
KD-24
KD-25
KD-26
KD-57
KD-64
KD-65
Carrying Handle
Capacitor Cover
Screw for Capacitor Cover
Capacitor
Paper
Switch
Clutch Spring
Retaining Ring
Rear Ball Bearing
Rear Ball Bearing Spring Washer
Clutch Nut
Shaft Lock Nut
Front Ball Bearing Retainer Screw
Front Ball Bearing
Front Ball Bearing Retainer
5
Front to Rear Bearing Nut
Crank
Crank Ball Bearing
Crank Ball Bearing Lock Nut
Screw for Brg Shaft
Shaft for Ball Bearing
Oil Pad Holder
Oil Cup
Oil Tube for Wrist Pin (Copper)
Oil Tube for Wrist Pin
Connecting Rod
Shakeproof Washer
Connecting Rod Clamp Screw
Wrist Pin
Wrist Pin Plug
Knife Lock Washer
Nuts for Guide Screw
Guide Washer
Connecting Rod Washer
Guide Adjusting Screw
Guide Adjusting Nut
KD-13
KD-27
KD-28
KD-29
KD-30
KD-31
KD-32
KD-33
KD-34
KD-35
KD-36
KD-37
KD-38
KD-39
KD-40
KD-41
KD-42
KD-43
KD-44
KD-45
KD-46
KD-47
KD-48
KD-49
KD-50
KD-51
KD-52
KD-53
KD-54
KD-55
KD-58
KD-59
KD-61L
KD-61R
KD-66
KD-69
KD-70
KD-71
KD-72
KD-73
KD-75
KD-76
Guide Lock Screw
R.H. Guide
L.H. Guide
Cross Head
Knife Lock Bolt
Terminal Block Screw
Ground Clip Screw
Set Screw
Front Bearing Housing
Oil Pad Holder Screw
Guide Hold Down Screw
Stud Lower L.H. Mounting (L)
Stud Lower L.H. Mounting (R)
Ground Clip
Attachment Plug (Complete)
Terminal Block (Complete)
Terminal Sleeve
Terminal Contact with Pin
Operating Handle
Switch Cover Screw
Switch Cover
6
Standard-to-Bearing Screw
Plate Wing
Plate
Roller
Rubber
Hinge Pin Short
Hinge Pin Clamp Screw
Plate Wing Tension Spring
Knife Slide Screw
Standard
Knife Slide
Screw for Throat Plate
Throat Plate
Plate Screw
Plate Nut
Knife
KD-63
KD-77S
KD-77L
KD-80C
KD-80R
KD-81
KD-82
KD-83
KD-84
KD-85
KD-86
KD-87
KD-88
KD-90S
KD-90N
KD-191
7
Screw for Latch
Shaft for Cam
Cam Shaft Spring Screw
Press Foot Lock Bracket Screw
Spring for Pressure Foot Lock
Spring for Latch
Cam Spring
Pressure Foot Rod
Screw for Pressure Foot Shoe
Pressure Foot Lever
Pressure Foot Lever Screw
Spring for Pressure Foot Lever
Set Screw for Cam
Cam
Release Lever
Screw for Cam
Lock Screw for Release Lever
Spring Washer
Washer
Lock (only) Pressure Foot
Screw for Press Ft Lock
Nut for Press Foot Lock
Pressure Foot Lock Bracket
Slide for Pressure Foot Rod
Latch for Cam
Pressure Foot Shoe
KD-96
KD-97
KD-98
KD-99
KD-109
KD-110
KD-111
KD-112
KD-113
KD-114
KD-115
KD-116
KD-117
KD-118C
KD-118L
KD-118S
KD-119S
KD-119SW
KD-119W
KD-120
KD-121S
KD-121N
KD-122
KD-123
KD-124
KD-125
Sharpener Hold Down Screw
Lower L.H. Sharpener
Hold down Nut
Stud, Guide Rod Bracket
Cap for Tube
Driving Shaft
Right and Left Hand Follower
Screw for Cover (S)
Screw for Cover (L)
Cover Over Cam
Spring for Bell Crank
Sharpener Housing
Bottom Plate Screw
Bottom Plate
Oil Pad & Holder
Screw for Oil Pad
Bell Crank With Pin & Bushing
Screw for Cover
Cover for Driver
KD-56
KD-60
KD-62
KD-92
KD-93
KD-94
KD-100S
KD-100L
KD-101
KD-126
KD-127
KD-128
KD-129
KD-130
KD-131
KD-132
KD-133
KD-134
KD-139
KD-140
KD-141
KD-142
KD-143
KD-144
KD-145
KD-146
KD-148
KD-149
KD-150
KD-151
KD-152
KD-153
KD-154
KD-155
KD-156
KD-157
Push Rod
Roll Pin for Push Rod
Driver Shaft With Gear
Screw for Spreader Pin
Spreader Pin
Gear & Shaft
Bearing for Gear
Rubber Driver & Driver & Driver Pulley
Spur Gear
Ball Bearing for Crank
Retaining Ring
Thrust Washer for Spiral Gear
Lock Nut for Crank Shaft
Shaft for Crank
Washer for Crank Shaft
Lock Nut for Ball Bearing
Ldler Gear With Bushing
L.H. Spiral Gear With Key
8
Collar for Lower Screw Shaft
Thrust Ball Bearing
Nut for Screw Shaft L.H. & R.H.
Washer for Screw Shaft L.H.
Screw Shaft With Extension
Spacer Tube
Stop Nut for Screw Shaft
Right Hand Follower Nut
R.H. Square Shaft
Left Hand Follower Nut
L.H. Square Shaft
L.H. Square Shaft Washer
Screw for Gear Cover
Grease Plug
Screw for Stabilizer
Lower Gear Bracket
Screw for Slide Pulley
Lower Gear Bracket Gear Cover
Adjusting Nut
Adjusting Screw
Gear on Screw Shaft
Intermediate Gear
KD-102
KD-103
KD-104
KD-105
KD-106
KD-107
KD-108
KD-135
KD-136
KD-137
KD-138
KD-138W
KD-158
KD-160
KD-161
KD-162
KD-163
KD-164
KD-165N
KD-165S
KD-166
KD-167
KD-168
KD-169
KD-170
KD-171
KD-172
KD-173
KD-174
KD-175
KD-176
KD-177
KD-178
KD-179
KD-180
KD-181
KD-182
KD-183
KD-184
KD-185
KD-186
KD-187
KD-188
KD-189
Bushing for Shoe
R.H. Shoe
L.H. Shoe
Set Screw for Sharpener Shoe
Stabilizer
Guide Back of Standard
Washer for Guide Back
Screw for Guide Back
L.H. Slide With Pulley
R.H. Slide With Pulley
Neoprene Band
Front Pulley for Belts
Roll Pin for Pulley
Spring for Pulley Slide
Screw for Clamping Arm
Clamping Arm for Shoe
Nut for Sharpener Shoe Screw
Screw for Sharpener Shoe
R.H. Sharpener Shoe Spring
L.H. Sharpener Shoe Spring
Spring for Arm
Abrasive Belts
9
Abrasive Belts
Electric Cord Complete
Knife
Slot Cleaner
Knife Bolt Wrench
Screw Driver
Wrench for Shoe Set Screw
Oiler
KD-189
KD-190
KD-191
KD-192
KD-194
KD-195
KD-196
KD-199
10
Reliable Corporation (“Reliable”) warrants to original purchaser of its products that
every product sold by Reliable (a “Reliable Product”) is free from defects in material and
workmanship for a period of one year from the date of purchase if properly used and
maintained. Subject to the conditions and limitations set forth below, Reliable will either
repair or replace any part of a Reliable Product that proves defective by reason of improper
workmanship or materials. If the defective Reliable Product is no longer available and cannot
be repaired effectively or replaced with an identical model, Reliable shall replace the defective
Reliable Product with a current Reliable Product of equal or greater value. Repaired parts or
replacement products will be provided by Reliable on an exchange basis, and will be either new
or refurbished to be functionally equivalent to new. If Reliable is unable to repair or replace
a Reliable Product, it will refund the current value of that Reliable Product at the time the
warranty claim is made.
This limited warranty does not cover any damage to a Reliable Product that results from
improper installation, accident, abuse, misuse, natural disaster, insufficient or excessive
electrical supply, abnormal mechanical or envsteamermental conditions, wear and tear
resulting from normal use of the product, or any unauthorized disassembly, repair, or
modification. This limited warranty does not extend to any indirect, consequential or incidental
damages that may be suffered by a user or from the use of a Reliable Product, including
without limitation, any liability for third party claims for damage, and is limited to the amount
paid by the original purchaser Reliable Product with respect to which this limited warranty
protection applies. This limited warranty does not apply with respect to products that have
been altered or which are missing serial numbers or for products not purchased directly from
Reliable or a dealer authorized by us to sell Reliable Products.
This limited warranty is the only warranty that applies to any Reliable Product, supersedes any
and all terms that may be contained in any other document or purchase order and may not be
altered or amended except expressly in writing by Reliable.
To obtain a repair or replacement under the terms of this warranty, please contact our
customer service group at 1-800-268-1649 or at support@reliablecorporation.com.
You will be required to submit an original receipt via fax or e-mail. The receipt must reflect that
you are the original purchaser, the product was bought directly from
us or from an authorized Reliable dealer and that the warranty claim is being made within the
warranty period. You will be issued a return authorization number (RA#) and asked to ship the
defective product together with proof of purchase and RA#, prepaid insured to the following
address:
Reliable Corporation, 5-100 Wingold Avenue, Toronto, ON M6B 4K7. Freight collect shipments
will be refused. The risk of loss or damage in transit will be borne by
the customer. Once Reliable receives the defective product, it will initiate the repair or
replacement process.
If you have any questions regarding this warranty, you may write to:
Reliable Corporation
100 Wingold Avenue, Unit 5
Toronto, Ontario
Canada M6B 4K7
www.reliablecorporation.com
RELIABLE PRODUCTS WARRANTY
11
1 800 268 1649
www.reliablecorporation.com
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
