American Standard M968120 User manual
- Category
- Sanitary ware
- Type
- User manual
This manual is also suitable for
CENTERSET
LAVATORY FAUCET
Installation
Instructions
M968120
Thank you for selecting American-Standard...the benchmark
of fine quality for over 100 years.
To ensure that your installation proceeds smoothly--please
read these instructions carefully before you begin.
Certified to comply with ANSI A112.18.1M
2930.000
THUMBSCREW
INDEX
BUTTON
HANDLE
SCREW
LEVER
HANDLE
CARTRIDGE
LIFT
ROD
MOUNTING
NUT
COUPLING
NUT
STOPPER
DRAIN
FLANGE
GASKET
WASHER
LOCKNUT
DRAIN
BODY
EXTENSION
TAILPIECE
TAILPIECE
INSERT
CLIP
PIVOT
ROD
0-RING
BUSHING
AERATOR
Product names listed herein are trademarks of American Standard Inc.
©American Standard Inc. 1999
SERVICE
ALIGN HANDLES
1
4
TEST INSTALLED FAUCET
INSTALL FAUCET
3
Remove AERATOR.
Turn HANDLES to OFF position.
Slowly turn on water supplies and check all connections
for leaks.
Operate both HANDLES to flush water lines thoroughly.
Operate LIFT ROD and check DRAIN connections for leaks.
Turn HANDLES to OFF position and replace AERATOR.
AERATOR may accumulate dirt causing distorted and reduced
water flow. Remove AERATOR and rinse clean.
Turn HANDLES to their off position.
Remove INDEX BUTTON and HANDLE
SCREW.
Remove HANDLE and replace on
VALVE STEM in desired position.
Replace HANDLE SCREW and INDEX
BUTTON.
Apply a bead of PUTTY along the edge of the underside of the BODY. Insert
faucet SHANKS through holes of SINK.
Turn off hot and cold water supplies before beginning.
CAUTION
Place faucet as far forward as possible.
Assemble and tighten MOUNTING NUTS from underside of SINK.
Connect the HOT water supply to the left SHANK and the COLD water supply to
the right SHANK using sealant, appropriate connectors, and COUPLING NUTS.
Insert LIFT ROD through hole in BODY.
SHANK
PUTTY
BODY
LIFT
ROD
SINK
MOUNTING
NUT
COUPLING NUT
HOT
COLD
M968120
INSTALL POP-UP DRAIN
INDEX
BUTTON
HANDLE
SCREW
LEVER
HANDLE
VALVE
STEM
HOT LINE FOR HELP
For toll-free information and answers to your questions, call:
1 (800) 223-0068
Weekdays 8:00 a.m. to 7:00 p.m. Eastern Time
Saturdays 8:00 a.m. to 4:00 p.m. Eastern Time
IN CANADA 1-800-387-0369 (TORONTO 1-416-536-5609)
STOPPER
Thread TAILPIECE into DRAIN BODY and tighten securely.
Thread LOCKNUT fully onto DRAIN BODY. Drop WASHER
and GASKET onto DRAIN BODY.
Remove CLIP from PIVOT ROD. Assembly PIVOT ROD
to DRAIN BODY with BUSHING.
Apply a bead of putty to underside of FLANGE.
Insert DRAIN BODY from below through SINK
hole with the PIVOT ROD pointed toward the LIFT ROD.
Thread FLANGE fully onto DRAIN BODY. Tighten
LOCKNUT firmly, keeping the PIVOT ROD pointed
toward the LIFT ROD.
Slide EXTENSION onto LIFT ROD and insert PIVOT ROD
through the second or third hole. Secure with CLIP.
EXTENSION may need to be bent to suit installation.
Drop STOPPER into DRAIN BODY. Operate LIFT ROD.
Adjust STOPPER movement by repositioning EXTENSION
on LIFT ROD.
Move PIVOT ROD fully downward. Tighten THUMBSCREW.
FLANGE
SINK
GASKET
PIVOT
ROD
DRAIN
BODY
PUTTY
WASHER
LOCKNUT
TAILPIECE
TAILPIECE
INSERT
TRAP
TAILPIECE
CLIP
THUMBSCREW
LIFT ROD
EXTENSION
ROD
2
TRAP
EXTENSION
ROD
CLIP
PIVOT
ROD
BUSHING
0-RING
-
1
-
2
American Standard M968120 User manual
- Category
- Sanitary ware
- Type
- User manual
- This manual is also suitable for
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
American Standard 7501 Series User manual
-
-
-
-
-
-
-
-
-
