Fontaine by Italia MFF-HVC1-MB Installation guide

MFF-HVC1-MB
Fontaine by Italia
Brand
Fontaine by Italia
Model
MFF-HVC1-MB
Category
Sanitary ware
Type
Installation guide

This manual is also suitable for

Fontaine by Italia MFF-HVC1-MB is a single handle lavatory faucet that combines style and functionality. It features a sleek and modern design that complements various bathroom decors. With its ADA-compliant design, it ensures accessibility for individuals with disabilities. The faucet is NSF/ANSI 61 certified, ensuring compliance with strict safety and quality standards. It boasts a maximum flow rate of 1.5 GPM, promoting water conservation without compromising performance.

Fontaine by Italia MFF-HVC1-MB is a single handle lavatory faucet that combines style and functionality. It features a sleek and modern design that complements various bathroom decors. With its ADA-compliant design, it ensures accessibility for individuals with disabilities. The faucet is NSF/ANSI 61 certified, ensuring compliance with strict safety and quality standards. It boasts a maximum flow rate of 1.5 GPM, promoting water conservation without compromising performance.

MFF-HVC1-CP
MFF-HVC1-BN
MFF-HVC1-MB
15122868-B
Installation Instructions
Hôtel de Ville
Single Handle Lavatory Faucet
Applicable Standards/Codes
Installation Dimensions
1
MFF-HVC1-CP
MFF-HVC1-BN
MFF-HVC1-MB
15122868-B 4
For easy installation of your faucet you will need:
● To read all the installation completely before beginning.
● To read all warnings, care, and maintenance information.
1 13/16＂
5 3/16＂
2 1/8＂
1 1/4＂
6 3/8＂
9/16-24 UNEF
7 3/8＂
5 1/ 2＂
3 1/ 2＂
8 3/8＂
2 3/16＂ MAX
1 5/16＂ - 1 1/ 2＂
L e n g t h 3 0 11 / 1 6＂
IAPMO certified to meet or exceed the following:
● ASME A112.18.1/CSA B125.1
● Uniform Plumbing Code
● National Plumbing Code of Canada
● NSF/ANSI 61
● Section 116875 of the California Health & Safety Code
● EPA WaterSense
● ADA Compliant
NSF/ANSI 61
NSF/ANSI 61
•
CUSTOMER SERVICE
TOLL-FREE 1-877-482-5422
MFF-HVC1-CP
MFF-HVC1-BN
MFF-HVC1-MB
Installation Instructions
15122868-B 2 15122868-B3
Seat seal into under side of faucet
base. Feed faucet supplies, mounting
stud and lift rod through the mounting
hole of lavatory or mounting surface.
3
Hot
MAX 25"
Cold
Cold
From below, push gasket and retaining washer onto mounting stud.
Secure faucet with mounting nut, pulling faucet to front of sink so supplies
rests against mounting hole. Before final tightening make sure collar on
mounting nut is seated into retaining washer. Adjust faucet so that it is
centered. Tighten mounting nut to complete faucet mounting.
4
Remove mounting nut and both C
shape washers from the shank of
the faucet.
1
Insert lift rod through the shank from the bottom. Then connect lift rod with
the lift rod knob. Ensure knob is screwed tight.
2
7
Assemble pivot rod, pivot nut, clip and seal as shown. Hand tighten pivot nut. Drop stopper into drain. (For vandal proof
drain rotate stopper so pivot rod goes through eye of stopper. Make connection to "P" trap.)
Remove one end of clip from pivot rod by squeezing ends together while sliding.
Insert pivot rod into second or third hole in extension and reassemble clip. (Extension may need to be bent).
Adjust stopper height by repositioning extension and tightening thumbscrew.
Place seal with small end facing up into tailpiece and tighten against drain
body. Pivot rod opening in tailpiece should face the rear of the lavatory.
Tighten lock nut with channel locks. Do not over tighten.
6
Connect flexible supplies directly to wall supplies. Connection on fitting supplies are 9/16"-24 UNEF compression.
Connect left supply to hot (Marked with a red band) and right supply to cold wall supply.
Faucet supplies are 25" long from faucet base.
Note: If additional supply length is required, installer must purchase additional parts separately.
Important: If supply hoses are to long, loop as illustrated to avoid kinking.
8
With handle in Off position, turn on water supplies and check all connections for leaks.
Remove aerator.
Operate handle to flush water lines thoroughly.
Replace aerator.
Check drain connections
Operate pop-up knob and fill lavatory with water. Check that drain stopper makes a good seal and retains water in sink.
If drain stopper does not seal properly, adjust pop-up rod.
Release pop-up knob down and check all drain connections and "P" trap for leaks. Tighten if necessary.
9
Drop flange into lavatory drain. From
below assemble rubber gasket,
metal washer and lock nut. Do not
tighten.
5
Off
On
Pop-up knob
Drain stopper
Hot
Pop-up rod
"P" trap
9/16"-24 UNEF
Pivot rod
"P" trap
Clip
Extension
thumbscrew
Pivot nut
Seal
Stopper
Eye
•
  • Page 1 1
  • Page 2 2

Fontaine by Italia MFF-HVC1-MB Installation guide

MFF-HVC1-MB
Fontaine by Italia
Brand
Fontaine by Italia
Model
MFF-HVC1-MB
Category
Sanitary ware
Type
Installation guide
This manual is also suitable for

Fontaine by Italia MFF-HVC1-MB is a single handle lavatory faucet that combines style and functionality. It features a sleek and modern design that complements various bathroom decors. With its ADA-compliant design, it ensures accessibility for individuals with disabilities. The faucet is NSF/ANSI 61 certified, ensuring compliance with strict safety and quality standards. It boasts a maximum flow rate of 1.5 GPM, promoting water conservation without compromising performance.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents