CENTERSET LAVATORY FAUCETS
WITH GOOSENECK SPOUT
Installation
Instructions
7500 Series
7501 Series
7502 Series
7545 Series
Thank you for selecting American-Standard...
the benchmark of fine quality for over 100 years.
To ensure that your installation proceeds smoothly--
please read these instructions carefully before you begin.
Certified to comply with ANSI A112.18.1M
60185 Rev. 1.5
TEST INSTALLED FAUCET
4
Remove AERATOR.
With handle in OFF position, turn on water supplies and check
all connections for leaks.
Operate both handles to flush water lines thoroughly. Check
spout mounting and hose connections for leaks.
Operate LIFT ROD and check DRAIN for leaks.
Turn handles into OFF position and replace AERATOR.
1
3
Apply a bead of PUTTY around underside
of DRAIN PLUG FLANGE (1). Insert DRAIN
PLUG (2) into SINK drain hole.
Hold DRAIN PLUG (2) to prevent turning
and assemble GASKET (3), WASHER (4)
and LOCKNUT (5) from underneath sink.
Insert threaded end of TAILPIECE (6)
into lower end of DRAIN PLUG (2).
Connect other end to trap.
GRID DRAIN ASSEMBLY
(Model 7502 only)
PUTTY
SINK
SINK
PUTTY
2
Asesemble GASKET (1) to SHANKS (2) and insert FAUCET SHANKS through holes of SINK.
Assemble RUBBER (3) and BRASS WASHERS (4), and LOCKNUTS (5) from underside of SINK. Drop
UPPER LIFT ROD (6) through hole in BODY (models 7501 only), align BODY as far forward as possible
and secure position by tightening LOCKNUTS (5).
Connect the HOT water supply to the left SHANK and the COLD water supply to the right
SHANK using sealant, appropriate connectors, and COUPLING NUTS (7).
Unscrew SPOUT NUT (8) and remove SPOUT (9).
To change spout to a swivel spout: (7500, 7501 & 7502)
Take SPOUT CLIP (10) off SPOUT (9) and remove RUBBER RING (11).
Replace RUBBER RING (11) with seperate PLASTIC RING (12) packed with faucet.
Put SPOUT CLIP (10) on SPOUT.
Reassemble SPOUT (9) to BODY.
2
8
9
10
11
12
BODY
SINK
3
4
5
7
6
HOT
COLD
1
1
2
3
4
5
2
10
1
7
7
2
12
12
3
4
8
6
5
11
1/2" O.D. SLIP
INSTALL POP-UP DRAIN
(Model 7501 only)
Push TAILPIECE (1) down into TRAP
(threaded end up).
Thread LOCKNUT (2), WASHER (3) and
GASKET (4) onto DRAIN BODY (5).
Apply a bead of PUTTY to underside
of FLANGE (6).
Feed DRAIN BODY (5) up through SINK
and thread FLANGE (6) fully onto BODY (5).
Tighten LOCKNUT (2) firmly, keeping the
PIVOT ROD (7) pointed towards the back
of the SINK.
Drop STOPPER (8) into DRAIN BODY (5).
Pull TAILPIECE (1) up and thread tightly
into DRAIN BODY (5).
Position EXTENSION ROD (9) onto POP-UP
ROD (10) and tighten THUMBSCREW (11).
Remove one end of CLIP (12) from PIVOT ROD (7)
by squeezing ends together while sliding.
Insert PIVOT ROD (7) into second or third hole
in EXTENSION (9) and reassemble CLIP (12).
(EXTENSION may need to be bent.)
Adjust STOPPER (8) height by repositioning
EXTENSION and tightening THUMBSCREW (12).
TRAP
Turn off water at
main supply.
CAUTION
7
9
7500 Series
7501 Series
7502 Series
7545 Series
SERVICE
5
CARTRIDGE
SCREEN
To change direction of handle rotation,
proceed as follows:
Turn valve to OFF position.
Remove HANDLE and BONNET NUT.
Remove SPRING CLIP.
Lift STOP WASHER, turn 90° and replace.
Replace SPRING CLIP.
Replace BONNET NUT, HANDLE, SCREW,
and INDEX.
AERATOR may accumulate dirt causing distorted and reduced
water flow. Remove AERATOR and rinse clean.
If spout drips, operate handles several times from OFF to ON
position. Do not force - handles turn only 90°.
Plastic SCREEN in CARTRIDGE may accumulate
dirt causing reduced water flow. To clean, first
turn off hot and cold water supplies, then:
Remove HANDLE and BONNET NUT.
Remove CARTRIDGE by pulling up.
Thoroughly rinse plastic SCREEN at
base of CARTRIDGE.
Replace CARTRIDGE until flange is
tight against valve body.
Turn valves OFF.
Replace BONNET NUT, HANDLE, SCREW
and INDEX.
SPRING
CLIP
STOP
WASHER
90°
GRID DRAIN
POP-UP DRAIN
For toll-free information and answers to your questions, call:
1-800-442-1902
Weekdays 8:00 a.m. to 6:00 p.m. EST
IN CANADA 1-800-387-0369 (TORONTO 1-905-306-1093)
Weekdays 8:00 a.m. to 7:00 p.m. EST
IN MEXICO 01-800-839-1200
Product names listed herein are trademarks of American Standard Inc.
© AS America, Inc. 2008
HOT LINE FOR HELP
60185 Rev. 1.5
000690-0020A
HANDLE SCREW
904939-0020A
BONNET NUT
012087-0070A
SPOUT SEAL KIT
028617-0020A
POP-UP ROD
951764-0070A
CARTRIDGE
024220-0070A
COUPLING NUT
030255-0070A
MOUNTING KIT
911928-0070A
GASKET
051217-0020A
WRIST BLADE
HANDLE KIT
051211-0070A
INDEX KIT
051210-0020A
LEVER HANDLE
M923208-0070A
FLOW RESTRICTOR
(7500.180 ONLY)
051214-0070A
SWIVEL/FIXED
SPOUT RINGS
051322-0020A
VANDAL PROOF SCREW
M919646-0020A
SPOUT
A919641-0020A
SPOUT
(7500.180 ONLY)
066116-YYY0A
DRAIN STOPPER
EXTENSION ROD
TAILPIECE INSERT
0-RING
066117-YYY0A
FLANGE KIT
072574-0070A
070847-0070A
CLIP
066118-0070A
PIVOT ROD
900864-0070A
DRAIN BODY
066497-0020A
COMPLETE DRAIN BODY
070532-0070A
TAILPIECE
070532-0040A
TAILPIECE
015025-YYY0A
DRAIN COMPLETE
M922880-0020A
AERATOR,
1.5gpm/5.7L/min.
M922858-0020A
VR AERATOR,
0.35gpm/1.3L/min.
066114 -0020A
VR AERATOR,
0.5gpm/1.9L/min
M918014-0070A
ADAPTER
000690-0020A
HANDLE SCREW
051211-0070A
INDEX KIT
M918014-0070A
ADAPTER
-
1
-
2
American Standard 7500145.002 Installation guide
- Type
- Installation guide
- This manual is also suitable for
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
American Standard 8125 User manual
-
-
-
-
-
-
-
-
-
Other documents
-
Glacier Bay 89462 User manual
-
PF WaterWorks PF0725-BN-NO Installation guide
-
CMI 192-5894 Installation guide
-
-
-
Design House 545699 Installation guide
-
-
-
-
