Nvidia nForce 570 SLI User manual

TRADEMARK

All products and company names are trademarks or registered trademarks of their

respective holders.

These specifications are subject to change without notice.

Manual Revision 1.0

May 10, 2006

nVidianVidia

nVidia

nForce 570 SLI nForce 570 SLI

nForce 570 SLI

mainboardmainboard

mainboard

ff

f

or or

or

AMD SocAMD Soc

AMD Soc

kk

k

et et

et

AM2 (940-pin) AM2 (940-pin)

AM2 (940-pin)

prpr

pr

ocessorocessor

ocessor

User’User’

User’

ss

s

ManualManual

Manual

6000012MF5710

ii

DISCLAIMER OF WARRANTIES:

THERE ARE NO WARRANTIES WHICH EXTEND BEYOND THE

DESCRIPTION ON THE FACE OF THE MANUFACTURER LIMITED

WARRANTY. THE MANUFACTURER EXPRESSLY EXCLUDES ALL

OTHER WARRANTIES, EXPRESS OR IMPLIED, REGARDING ITS

PRODUCTS; INCLUDING ANY IMPLIED WARRANTIES OF

MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE OR

NONINFRINGEMENT. THIS DISCLAIMER OF WARRANTIES SHALL

APPLY TO THE EXTENT ALLOWED UNDER LOCAL LAWS IN THE

COUNTRY PURCHASED IN WHICH LOCAL LAWS DO NOT ALLOW OR

LIMIT THE EXCLUSION OF THE IMPLIED WARRANTIES.

HANDLING PROCEDURES:

Static electricity can severely damage your equipment. Handle the mainboard and

any other device in your system with extreme care and avoid unnecessary contact

with system components on the mainboard. Always work on an antistatic surface

to avoid possible damage to the mainboard from static discharge. Always have

the power supply unplugged and powered off when inserting and removing

devices within the computer chassis. The Manufacturer assumes no responsibility

for any damage to the mainboard that results from failure to follow instruction or

failure to observe safety precautions.

CAUTION

The mainboard is subject to damage by static electricity.

Always observe the handling procedures.

iii

Post Port Frequently Asked Questions

Below is a list of some basic POST Codes, possible problems and solutions. For more detailed

information about POST Codes, refer to Appendix in this manual.

Post Code Problem Solution

FFh or CFh

1. BIOS chip inserted incorrectly

2. Incorrect BIOS update version

3. Mainboard problem

4. Add-on card inserted incorrectly

1. Reinsert the BIOS chip

2. Download the correct BIOS version

update from the manufacturer's

Web site

3. Replace mainboard

4. Remove and replace the add-on card

C1h - C5h

1. Memory module inserted incorrectly

2. Memory compatibility problem

3. Memory module damaged

1. Reinsert memroy module

2. Replace memory with correct type

3. Replace memory module

2Dh

1. Error occured in VGA BIOS

2. VGA card inserted incorrectly

1. Replace VGA card

2. Reinsert the VGA card

26h

Overclock error Clear CMOS or press the insert key to

power on the system

07h - 12h

1. Initial Keyboard controller error

2. RTC error

1. Ensure the Keyboard and mouse are

connected correctly

2. Replace the RTC battery

iv

Table of Contents

Section 1--Section 1--

Section 1--

IntroductionIntroduction

Introduction

........................................................................................................................................................

............................................................................

11

1

1-1 Package Contents ................................................................................1

1-2 Mainboard Features ..............................................................................2

1-3 Mainboard Specification .........................................................................4

1-4 System Block Diagram ...........................................................................6

Section 2--Section 2--

Section 2--

InstallationInstallation

Installation

..............................................................................................................................................................

...............................................................................

77

7

2-1 CPU Installation ....................................................................................7

2-2 Rear I/O Fan Installation........................................................................8

2-3 Jumper Settings ...................................................................................8

2-4 System Memory Configuration ...............................................................9

2-5 Rear I/O Port........................................................................................10

2-6 Internal Connectors ..............................................................................10

Section 3--Section 3--

Section 3--

BIOS SetupBIOS Setup

BIOS Setup

........................................................................................................................................................

............................................................................

1313

13

3-1 Main Menu............................................................................................13

3-2 Standard CMOS Setup ..........................................................................14

3-3 Advanced BIOS Features ......................................................................14

3-4 Power BIOS Features............................................................................16

Section 4--Section 4--

Section 4--

Driver & UtilityDriver & Utility

Driver & Utility

................................................................................................................................................

........................................................................

1818

18

Section 5--Section 5--

Section 5--

Ghost BIOSGhost BIOS

Ghost BIOS

........................................................................................................................................................

............................................................................

1919

19

Section 6--Section 6--

Section 6--

AppendixAppendix

Appendix

..................................................................................................................................................................

.................................................................................

2121

21

6-1 Post Codes...........................................................................................21

Page

Introduction

1

English

Contents

A. Mainboard

B. User’s manual

C. Floppy drive cable

D. HDD drive cable

E. CD (drivers and utilities)

F. I/O Shield

G. SATA II data cable

Optional items

H. Extra USB2.0 port cable

I. COM port bracket

J. Printer port bracket

K. Thermo Stick cable

L. Rear I/O fan

Section 1 -- Introduction

1-1 Package Contents

When installing Windows XP/2000 into any RAID drive, the O/S setup will require a floppy disk containing the RAID

driver. This step will show you how to prepare this driver floppy.

1. Locate a PC and insert the bundled CD into its CD-ROM drive.

2. A main menu screen will appear (Autorun feature)

3. Select the page “RAID floppy”

B

A

C

D

USER’S

MANUAL

E

F

H

K

G





If you intend to setup RAID:

4. Insert a blank floppy into the A:drive

5. Click on the required RAID controller driver to begin copy into the floppy

If you need the optional item, please contact

your dealer for assistance.

I J

L

Introduction

2

English

1-2 Mainboard Features

Brief Introduction

Socket AM2

Socket AM2 (940-pin) based motherboards are designed to provide performance enhancements for AMD Athlon

AM2 processor-based systems, and it also expected to be the next-generation of platform innovations.

For more information about all the new features Athlon

TM

AM2 Processor deliver, check out the AMD website

at

http://www.amd.com

Chipset

The board is designed with nVidia nForce 570 SLI chipset, featuring performance and stability with the most

innovative technology and features.

For more details about the nVidia chipset, please visit the nVidia Web site at

http://www.nVidia.com.

PCI-Express (PCI-E)

Next generation peripheral interface to succeed to current PCI bus for the next decade. With smaller slot size

and 250MB/sec (PCI-E*1) or 4GB/sec(PCI-E*16) maximum transfer, PCI-Express overcomes PCI bus

bottleneck.

NVIDIA SLI

NVIDIA SLi

TM

technology revolutionizes PC performance by combining multiple PCI Express GPUs in a single

and scalable system! Gamers and hardcore enthusiasts know that dual GPUs mean increased, supercharged

3D graphics and performance.

DDRII

DDRII ushers in the new era of DDR memory technology. DDRII memory offers faster speed, higher data

bandwidth and lower power consumption over DDR.

Dual Channel

Supports dual channel of DDRII memory to give you twice the memory bandwidth for greater system

performance.

Hardware Monitoring

Hardware monitoring enables you to monitor various aspects of the system operation and status. This

includes CPU temperature, voltage and fan speed in RPMs.

Dual GbE LAN

Onboard two Gigabit-LAN controllers. This twin set of Gigabit-LAN breaks traditional bandwidth barrier,

delivering maximum 1000Mbps between internal and external network.

Serial ATA II

S-ATA II is the second generation SATA interface with double the transferring speed up to 300MB/sec. It

supports NCQ to provide faster reading speed for your storage devices.

SATA RAID

RAID function available on chipset’s SATA II ports, RAID 0, 1, 0+1, 5 by NV driver support.

More S-ATA II (Optional)

An extra S-ATA II controller is added to allow for more S-ATA II ports expansion in the form of JMicron’s

JMB363 complete with RAID function.

e-SATA (Optional)

With this new standard, you can now hot-plug external SATA drives to your system similar to USB devices.

With transfer speed up to 6 times faster than USB2.0, RAID capabillity and Port Multiplier function, e-SATA

brings unseen before performance to storage out of the box. This function is available only on S-ATA II ports

from JMicron’s JMB363 controller.

USB2.0

A popular USB standard for plugging in peripherals with up to 480Mbps transfer speed while maintaining

backward compatibility with older USB1.1 device.

8ch

Delivers 8 channel audio to bring you the latest in audio realism from DVD movies and games. Perfect for your

home theatre system.

Introduction

3

English

AMD Cool'n'Quiet

TM

Technology

AMD's Cool'n'Quiet

TM

Technology lowers CPU operating voltage when the system is in idle mode. This helps to

reduce heat dissipation and in effect lowers the fan speed to noise from your PC.

NVIDIA Firewall (Optional)

An unprecedented addition design for nForce product, provide high performance & enhanced reliability of PC

security solution to the users. The features would be more advanced than many stand-alone firewalls can

provide!

NVIDIA ActiveArmor

TM

(Optional)

Enhances networks security while delivers the highest system performance by off-loading CPU-intensive

packet filtering tasks in hardware, providing users with a PC networking environment that is both fast and

secure.

Ghost BIOS

No more worries if BIOS gets corrupted causing your system unable to boot. The onboard backup BIOS will

rescue & recover main BIOS in just a few easy steps.

Thunder Probe

A hardware diagnostic software to monitor voltage, temperature and speed of a variety of hardware. It also

includes an ingenious built in fan control feature called Smart Fan.

Thunder Flash

A Windows based innovation tool to provide safe and easy BIOS rescue function, BIOS flash function and

personal start up screen.

Magic Health

Reports your system hardware status for every boot-up to help detect faults early. Monitor hardware status

including CPU temperature, CPU/Memory/Chipset voltage, fan RPM speed for chassis fan, CPU fan & Power

supply fan.

EZ-Boot

Simply press “ESC” to select your bootable device. No more hassle to search the BIOS menu, change and

re-start.

PowerBIOS

Supporting a full range of overclocking setting via BIOS. Various adjustable feature include FSB/Memory/

Chipset voltage tweaking.

Special Features

BIOS Features:

Post Port

An onboard LED-display trouble-shooting device, facilitating user to detect boot-up problems.

QuickSPDIF

On board SPDIF-out connector for quick connection to multi-channel speakers. Not only removes cable

cluttering but also delivers loss-free digital audio to let you enjoy DVD movies and games with crystal clear

sound.

EZ-Button

A handy power-on button located onboard to turn on/off the system easily, especially while debugging or

testing the system.

LEDION

Onboard LED indicators to show the power status CPU, Chipset and DRAM. You know immediately where to

look if the system fails to start.

Thermo Stick (Optional)

Flexible thermometer to let you measure any temperature by software. Ideal for monitoring VGA card,

chipset or even disk drives temperatures.

H/W Features:

Introduction

4

English

roloCkcaJenohP lennahc2 lennahc6 lennahc8

eulBthgiLni-eniLni-eniLni-eniL

emiLtuo-eniLtuo-oeretstnorFtuo-oeretstnorF

kniPni-ciMni-ciMni-ciM

yarGtuo-oeretsediS

kcalBtuo-oeretsraeRtuo-oeretsraeR

egnarOrefoowbuS&retneCrefoowbuS&retneC

1-3 Mainboard Specification

Processor

 Support Socket-AM2 (940-pin) based AMD Athlon-AM2 with 2GTs 16x16 Hyper Transport processors

 Support VMM (Virtualization-Machine-Monitoring)

Chipset

 nVidia nForce 570 SLI

Main Memory

 Four 240-pin unbuffered non-ECC DDRII SDRAM DIMM sockets

 Support single-sided or double-sided 1.8v DDRII-533/667/800 DIMMs with dual channel architecture in

256Mb/512Mb/1Gb technologies

 Supports up to 16GB memory size

Expansion Slots

 Three PCI connectors compliant with PCI v2.3

 Two PCI-E (x1) connectors compliant with PCI Express 1.0a

 Two PCI-E (x16) connectors compliant with PCI Express 1.0a to support SLi technology

USB

 Ten USB connectors compliant with USB2.0 from embedded USB controller (4 connectors at rear panel)

LAN

 Two Gigabit Ethernet from onboard Marvell 88E1116 Gigabit Ethernet PHY

P-ATA IDE

 One IDE interface (up to 2 IDE devices) with UDMA-33/66/100/133 support from embedded IDE controller

S-ATA RAID

 Six S-ATA II ports with up to 300MB/s from chipset with RAID 0, 1, 0+1, 5

More S-ATA (Optional)

 Two S-ATA II ports and One P-ATA port from JMicron's JMB363 PCI-Express to 2S1P controller and e-SATA

support.

I/O

 Onboard EPoX EP1308 LPC bus I/O controller

 Legacy peripheral interface for PS/2 keyboard & mouse, FDD, Parallel, Serial, and IrDA (v1.0 compliant)

 Support Hardware Monitoring for fan speed monitoring and CPU temperature sensing

 Intelligent fan speed control for CPU-fan (PWM) and Chassis-fan for quiet operation

Audio

 8 channel audio from onboard Realtek ALC8xx High Definition audio compliant CODEC

- Support CD-In

- Support Jack detection for fool-proof audio device installation

- Rear panel audio jacks configuration:

Introduction

5

English

BIOS

 Flash EEPROM with Award Plug&Play BIOS

 Support EZ Boot for fast bootable device selection

 Support Magic Health for system hardware status report during system boot-up

 Support Ghost BIOS for BIOS Recovery

Peripheral Interfaces

))

) At Rear Panel

 PS/2 keyboard and mouse ports

 One S/PDIF-Out Coaxial jack

 One S/PDIF-Out Optical

 One RJ45 LAN connector

 Four USB2.0 ports

 Six Audio jacks

))

) Onboard connector and pin-header

 One floppy drive connector

 One ATA-100/133 IDE connector from nVidia nForce 570 SLI

 One ATA-100/133 IDE connector from JMicron’s JMB363 (Optional)

 Six extra USB2.0 ports

 One CD-IN connector

 One IR connector

 One Parallel (printer) connector

 One Serial port (COM1) connector

 Six S-ATA II connectors from nVidia nForce 570 SLI

 Two S-ATA II connectors from JMicron’s JMB363 (Optional)

 Four Fan connectors

Front Panel Controller

 Supports Reset & Soft-Off switches

 Supports HDD & Power LEDs

 Supports PC speaker

 Supports Front Panel Audio connector

Special Features

 Support KBPO function – Keyboard power on, turn on the computer from keyboard

 Support Wake-On-LAN by PME

 Onboard Post Port LED display for system debugging

 PowerBIOS for excellent overclocking features:

- Programmable FSB and PCI-E Clock output frequency with 1MHz fine tuning

- Support BIOS adjustable CPU multiplier, FSB clock, PCI-E x16 clock, DIMM frequency

- Support BIOS adjustable CPU Core voltage, Chipset voltage and DIMM voltage

 Support EZ-Button – A handy power-on button onboard to turn on/off the system easily

 Support LEDION – onboard LED power indicator for CPU, DDR and chipset

 Support Thermo Stick temperature (Optional)

 Support Ghost BIOS - Rescue, recover BIOS in an easy step and no more worry of BIOS being corrupted.

Powerful utilities for Windows

 Support Thunder Probe - A hardware diagnostic software to monitor voltage, temperature and speed of

a variety of hardware. It also includes an ingenious built in fan control feature called Smart Fan.

 Support Thunder Flash - A Windows based innovation tool to provide safe and easy BIOS rescue

function, BIOS flash function and personal start up screen.

Introduction

6

English

1-4 System Block Diagram

Form Factor

 305mm x 245 mm ATX size



Depending on the model you purchased, some components are optional and may not be

available.

Introduction

7

English

Section 2 -- Installation

Always have the power supply unplugged and powered off when

inserting and removing devices within the computer chassis.

2-1 CPU Installation

Step 1

Open the socket by raising the actuation lever.

Step 2

(1) Align pin 1 on the CPU with pin 1 on the CPU socket as shown.

Insert the CPU and make sure it is fully inserted into the socket.

(2) Close the socket by lowering and locking the actuation lever.

Step 3

Insert the heatsink as shown. Press the clips in the direction of the

arrows shown to secure the assembly to the CPU socket.

Step 4

Plug the CPU fan power into the mainboard’s CPU fan connector.

The installation is complete.





The CPU is keyed to prevent incorrect insertion, do not force

the CPU into the socket. If it does not go in easily, check for

mis-orientation.

(1)

(2)





• Thermal compound and qualified heatsink recommended by

AMD are a must to avoid CPU overheat damage.

• Apply heatsink thermal compound/paste to the CPU.

Introduction

8

English

2-2 Rear I/O Fan Installation (Optional)

Step 1 :

First install the I/O shield and the mainboard to the computer

case as shown on the left.

Step 2 :

Place the fan behind the I/O shield and tighten it with the 4

screws included in the package.

Step 3 :

Plug the power to the 3-pin header JFAN2. Fan installation is

now complete.

2-3 Jumper Settings

JCMOS: Clear CMOS data Jumper

If the CMOS data becomes corrupted or you forgot the supervisor or

user password, clear the CMOS data to reconfigure the system back to

the default values stored in the ROM BIOS.

Settings:

1-2: Normal (Default)

2-3: Clear CMOS



 To CMOS Clear data, please follow the steps below.

1. Turn off the system.

2. Change the jumper from “1-2” to “2-3” position for a few

seconds.

3. Replace the jumper back to the “1-2” position.

4. Turn on the system and hold down the <Del> key to enter

BIOS setup.

Introduction

9

English

2-4 System Memory Configuration

The mainboard accommodates Four 240-pin DIMMs.

• Supports up to 16GB of 533/667/800MHz DDRII SDRAM.

• Supports unbuffered DIMM configurations defined in JEDEC DDRII DIMM specification.

DIMM 2

DIMM 4

Dual Channel 2

Dual Channel 1

DIMM 1

Dual Channel interface:

• Dual channel memory access offers increased system performance.

• For dual channel to operate, both channel must be populated with same amount of memory, preferably

of the same type.

• The four DIMM sockets are divided into two colors to help you identify the channel pairs <Figure 1>. Each

dual channel pair has the same color, e.g. DIMM1 and DIMM2. To obtain best performance, simply

mount DIMM sockets of the same color.

Memory configurations supported:

* SS: Single-Sided DIMM, DS: Double-Sided DIMM

MMID1

)tib-46(

MMID2

)tib-46(

MMID2

)tib-821(

MMID4

)tib-821(

1#MMIDSD/SSSD/SSSD/SSSD/SS

2#MMIDSD/SSSD/SS

3#MMIDSD/SSSD

/SSSD/SSSD/SS

4#MMIDSD/SSSD/SS

To install, align the notch on the DIMM module with the connector.

Press straight down as shown in the figure until the white clips close and the module fits tightly into the

DIMM socket.

Memory Installation :

Notch

Introduction

10

English

2-5 Rear IO Port

The I/O back panel for this mainboard is shown below. When installing the mainboard into the computer case, use the

bundled I/O shield to protect this back panel.

2-6 Internal Connectors

6

1

2

8

7

9

1016

3

1 4

3

5

12

13

15

14

11

USB2.0 x 4 ports

PS/2

Mouse

S/PDIF-out

Coaxial Jack

S/PDIF-out Optical

RJ45

LAN

7.1 Audio Channel

RJ45

LAN

PS/2

Keyboard

Introduction

11

English

Connectors Figure Descriptions

1

Ground

+12V

Sense

JCPU_FAN

JPWR_FAN

JSYS_FAN

JFAN2

CPU / Power / Chassis /IO Fan Power Connectors

JCPU_FAN: Connect the CPU fan to this connector.

JPWR_FAN: Use this connector if you are installing an

additional fan in the unit.

JSYS_FAN: The chassis fan will provide adequate airflow

throughout the chassis to prevent overheating

the CPU.

JFAN2: If you are installing the rear I/O fan in the unit,

connect to this fan connector.

2

FDD

Floppy Drive Connector

IDE1

Primary IDE

1

Primary IDE Connector

Connects to the IDE device, i.e. HDD and CD-ROM device.

4

PW1

PW12

PW1: 24-pin ATX Power Connector

PW12: 4-pin ATX12V Power Connector

The plugs of the power cables are designed to fit in only one

orientation.

5

CFPA

The PW1 and PW12 Power Connector must

be used simultaneously.

When using two IDE drives on the same

connector, one must be set to Master mode

and the other to Slave mode. Refer to your

disk drive user’s manual for details.

6

CD-IN: CD Audio-in connectors

This connector is used to receive audio from a CD-ROM drive,

TV tuner or MPEG card.

CD-IN

1

3

1

-12V3.3V

Ground+5V

PS-ON+5V

-5VPW-OK

+5V5VSB

+5V

Ground

+12V

3.3V

+12V+12V

23

11

4

2

3.3V3.3V

GroundGround

24

CD_IN_Left

1

CD_IN_Right

CD_Reference

CUSB3

CUSB4

CUSB5

CUSB3/CUSB4/CUSB5: Six USB2.0 header

This mainboard includes 6 additional onboard USB ports.

To use these additional USB ports, a USB bracket is required.

Please contact your retailer for details.

7

Ground

+12V

Sense

Control

CFPA: Front Panel Audio Connector

This audio connector connects to the audio jacks located on the

front panel. Refer to your case manual to match the pin-out

names.

10

2

91

MIC_In

Front Line-out-R

GND

NC

Key

+5V

NC

Front Line-out-L

IDE2

Secondary IDE

(Optional)

3

Secondary IDE Connector

Connects to the HDD device only.

Introduction

12

English

8

CFP

CFP: Case Front Panel Connector

 HD_LED

This LED indicates hard drive activity.

 PWR_LED

Connects to the power indicator on the PC case.

 RST

Connects to the RESET switch on the PC case.

 PW_ON

Connects to the Power button on the PC case, to turn on

the system. To turn off the system, press the power

button for 4 seconds.

CIR

CSPK

CIR: IR connector

For connection to an IrDA receiver unit.

CSPK: Speaker

Connects to the case’s speaker for PC beeps.

1

GND

A-B-

B+

GND

A+

GND

SATA1 ~ SATA6: Six S-ATA II Connectors

These connectors enable you to connect Serial ATA HDDs or

optical drives type.

9

Thermo Stick:

Flexible thermometer to let you measure any temperature by

software. Ideal for monitoring VGA card, chipset or even disk

drives temperatures.

THM-ST

(Optional)

13

CP80P: Post Port Debug LED

Provides two-digit POST code to show why the system fail to

boot. Allows quick and easy optimization.

The LED will display the CPU temperature when you run the

bundled Thunder Probe software.

CP80P

14

SATA7

SATA8

(Optional)

SATA7 ~ SATA8: Two S-ATA II Connectors

These connectors enable you to connect Serial ATA HDDs or

optical drives type with e-SATA.

10

LPT1: Parallel Port (printer) Connector

The parallel port can be used for printers and other parallel

device.

LPT1

12

1

GND

A-B-

B+

GND

A+

GND

EZ-Button — RESET, PW-ON:

These onboard buttons lets you turn on/off the system

easily, it is especially handy for debugging or testing the

system.

EZ-Button

15

Connectors Figure Descriptions

SATA1

SATA6

LEDION:

Onboard LED indicators to show the power status of CPU,

Chipset and DRAM. You know immediately where to look if the

system fails to start.

LEDION

11

Introduction

13

English

3-1 Main Menu

The ROM BIOS contains a built-in Setup program which allows user to modify the basic system configuration and

hardware parameters. The modified data is stored in a battery-backed CMOS, so that data will be retained even

when the power is turned off. In general, the information saved in the CMOS RAM will stay unchanged unless there

is a configuration change in the system, such as hard drive replacement or a device is added.

It is possible for the CMOS battery to fail causing CMOS data loss. If this happens you will need install a new CMOS

battery and reconfigure your BIOS settings.

To enter the Setup Program :

Power on the computer and press the <Del> key during the POST (Power On Self Test). The BIOS CMOS SETUP

UTILITY opens.

The main menu displays all the major selection items. Select the item you need to reconfigure. The selection is made

by moving the cursor, press any direction (arrow key ) to the item and pressing the ‘Enter’ key. An on-line help

message is displayed at the bottom of the screen as the cursor is moved to various items which provides a better

understanding of each function. When a selection is made, the menu of the selected item will appear so that the user

can modify associated configuration parameters.



 The BIOS setup screen and description are for reference only, and may not exactly match

what you see on your screen. The contents of BIOS are subject to change without notice.

Please visit our website for BIOS updates.

Section 3 -- BIOS Setup

Connectors Figure Descriptions

1

9

2

10

CTS

Ground

TXD

RI

RTS

RXD

DTR

DCD

DSR

COM1: Serial Port Connector

The serial port can be used with modems, serial printers,

remote display terminals, and other serial device.

COM1

16



 For more information regarding BIOS settings refer to the complete manual in the

bundled CD.

Introduction

14

English

3-2 Standard CMOS Setup

Choose “STANDARD CMOS FEATURES” in the CMOS SETUP UTILITY Menu. Standard CMOS Features Setup allows the

user to configure system settings such as the current date and time, type of hard disk drive installed, floppy drive

type, and display type. Memory size is auto-detected by the BIOS and displayed for your reference. When a field is

highlighted (use direction keys to move the cursor and the <Enter> key to select), the entries in the field can be

changed by pressing the <PgDn> or the <PgUp> key.

Notes:

• If the hard disk Primary Master/Slave and Secondary Master/Slave are set to Auto, the hard disk size and

model will be auto-detected.

• The “Halt On:” field is used to determine when the BIOS will halt the system if an error occurs.

3-3 Advanced BIOS Features

Selecting the “ADVANCED BIOS FEATURES” option in the CMOS SETUP UTILITY menu allows users to change system

related parameters in the displayed menu. This menu shows all of the manufacturer’s default values for the board.

Pressing the [F1] key displays a help message for the selected item.

Removable Device Priority

This item allows you to select the hard disk boot priority.

Options: Floppy, LS120, ZIP100, USB-FDD0, USB-FDD1, USB-ZIP0, USB-ZIP1.

Hard Disk Boot Priority

This item allows you to select the hard disk boot priority.

Options: Pri. Master, Pri. Slave, Sec. Master, Sec. Slave, USBHDD0, USBHDD1, USBHDD2, Bootable Add-in cards.

CD-ROM Boot Priority

This item allows you to select the CD-ROM boot priority.

Options: Pri. Master, Pri. Slave, Sec. Master, Sec. Slave, USB-CDROM0, USB-CDROM1.

Introduction

15

English

Init Display First

This item is used to select whether to initialize the PCI-E or PCI first when the system boots.

Options: PCI Slot, PCIEx.

First /Second/Third Boot Device

The BIOS attempts to load the operating system from the devices in the sequence selected in these items.

Options: Floppy, LS120, Hard Disk, CDROM, ZIP100, USB-FDD, USB-ZIP, USB-CDROM, Legacy LAN, Disabled.

Boot Other Device

When enabled, the system searches all other possible locations for an operating system if it fails to find one in the

devices specified under the first, second, and third boot devices.

Options: Enabled, Disabled.

Boot Up Floppy Seek

If this item is enabled, it checks the size of the floppy disk drives at start-up time. You don’t need to enable this item

unless you have a legacy diskette drive with 360K capacity.

Options: Enabled, Disabled.

Boot Up NumLock Status

This controls the state of the NumLock key when the system boots.

On: The keypad acts as a 10-key pad.

Off: The keypad acts like cursor keys.

Security Option

This category allows you to limit access to the System and Setup, or just to Setup.

System: The system will not boot and access to Setup will be denied unless the correct password is

entered at the prompt.

Setup: The system will boot, but access to Setup will be denied unless the correct password is

entered at the prompt.

APIC Mode

This item allows you to enable APIC (Advanced Programmable Interrupt Controller) functionality.

Options: Enabled, Disabled.

HDD S.M.A.R.T. Capability

The S.M.A.R.T. (Self-Monitoring, Analysis, and Reporting Technology) system is a diagnostics technology that

monitors and predicts device performance. S.M.A.R.T. Software resides on both the disk drive and the host

computer. If a device failure is predicted, the host software, through the Client WORKS S.M.A.R.T applet, warns the

user of the impending condition and advises appropriate action to protect the data.

Options: Enabled, Disabled.

Full Screen LOGO Show

This item allows you determine Full Screen LOGO display during POST.

Options: Enabled, Disabled.

Introduction

16

English

3-4 POWER BIOS Features

This page lets you adjust various parameters to obtain improved performance for overclocking.

Warning:

Overclocking requires expert knowledge and risks permanent damage to system components.

We recommend you leave these parameters at their default values for proper operation.

CPU Frequency

Enables you to increment the CPU’s clock generator at 1 MHz step. This works together with CPU Clock Ratio (below)

to set the CPU operating frequency.

CPU Clock Generator x CPU Clock Ratio = CPU Frequency

For example, if you have a processor that is rated at 2.4GHz and the clock generator is 200MHz, then 200MHz x 12

= 2.4GHz

Options: 200 to 450 in 1MHz increments.





Overclocking failure will cause no display on the monitor. To overcome this switch off the power supply

and switch on again. Restart the system, press and hold <

Insert>

key. This will revert the BIOS to

default or initial setting.

PCIE Clock

Enables you to subtle tune the PCIE frequency at increments of 1MHz step.

Options: 100 to 145 in 1MHz increments.

CPU Clock Ratio

Use this item to select a multiplier to set the CPU frequency. See CPU Frequency item above for explanation. If your CPU

multiplier is locked this option will be unavailable.

AMD K8 Cool’n’Quiet

Reduce the noise and heat from you PC when AMD’s Cool’n’Quiet

TM

technology is Auto.

Options: Auto, Disabled.

CPU Voltage

This item allows you to adjust the CPU Vcore voltage.

Options: Auto, -0.200V to +0.500V in 0.025V increments. We recommend that you leave this at the default value.

Chipset Voltage

This item allows you to adjust the Chipset voltage.

Options: +1.5V to +1.8V in 0.1V increments. We recommend that you leave this at the default value.

DIMM Voltage

This item allows you to adjust the DIMM slot voltage.

Options: Auto, +1.8V to +2.5V in 0.1V increments. We recommend that you leave this at the default value.

Page is loading ...

Nvidia nForce 570 SLI User manual

Nvidia nForce 570 SLI User manual

in other languages

Related papers

Other documents