IRIS QuietPower 1800 User manual

Brand: IRIS

Model: QuietPower 1800

Category: Power adapters & inverters

Type: User manual

Operator’s Manual

Iris Technology Corporation [CAGE 78535]

PO Box 5838, Irvine, CA 92616-5838

949.975.8410 tel / 949.975.8498 fax

Toll free 866.240.9540 / www.iristechnology.com

Document 287.F701 / 100412 / Rev 12 APR 2010

Supersedes Document 287.F701 / 070901 / Rev 01 SEP 07

QuietPower 1800 (QP-1800)

DC to AC Power Inverter

TM 11460A-OR/1 A

APRIL 2010

PCN 500 114600 00

Iris Technology Operator's Manual

QuietPower 1800 (QP-1800) Doc 287.F701 / 100412

Page 2 of 56 Rev 12 APR 2010

Notice of Copyright

Iris Technology QuietPower Inverter (QP-1800) Owner‟s Manual.

Disclaimer

Unless specifically agreed to in writing, Iris Technology Corporation (Iris):

(a) makes no warranty as to the accuracy, sufficiency, or suitability of any

technical or other information provided in its manuals or other documentation.

(b) assumes no responsibility or liability for loss or damage, whether direct,

indirect, consequential, or incidental, which might arise out of the use of such

information. The use of such information will be entirely at the user‟s risk.

Document Number

TM 11460A-OR/1 A / PCN 500 114600 00

287.F701 / 100412 / Rev 12 APR 2010

Supersedes Document 287.F701 / 070901 / Rev 01 SEP 07

U. S. Government Copyright Release

Iris Technology Corporation grants permission to the U.S. Government to reprint

this technical manual for use as needed. This permission includes but is not

limited to posting on U.S. Government websites. This document is subject to

periodic revision and the user is encouraged to check the Iris Technology

website (www.iristechnology.com) for the most current version of this document.

Trademarks

Any references to copyrighted or trademarked names referred to in this document

are the properties of their respective owners.

Iris Technology Operator's Manual

QuietPower 1800 (QP-1800) Doc 287.F701 / 100412

Page 3 of 56 Rev 12 APR 2010

TABLE OF CONTENTS

TABLE OF CONTENTS ......................................................................................................................................... 3

APPENDICES ..................................................................................................................................................... 5

LIST OF FIGURES ............................................................................................................................................... 5

LIST OF TABLES ................................................................................................................................................. 5

SYMBOLS AND CONVENTIONS ............................................................................................................................ 6

SPECIFIC WARNINGS AND HAZARDS OF THIS DEVICE .......................................................................................... 7

GENERAL SAFETY PRECAUTIONS ..................................................................................................................... 10

EXPLOSIVE GAS PRECAUTIONS ........................................................................................................................ 11

PRECAUTIONS WHEN WORKING WITH BATTERIES............................................................................................. 11

FCC INFORMATION .......................................................................................................................................... 12

DEPARTMENT OF DEFENSE PRODUCT EVALUATION .......................................................................................... 12

SECTION 1

INTRODUCTION

1.1 INTRODUCTION ................................................................................................................................................ 13

1.2 EQUIPMENT IDENTIFICATION AND DESCRIPTION ................................................................................................. 14

1.3 INVERTER KEY FEATURES ................................................................................................................................. 16

1.3.1 INVERTER FUNCTION ........................................................................................................................................ 16

1.3.2 CONTROL PANEL .............................................................................................................................................. 16

SECTION 2

INSTALLATION

2.1 GENERAL ......................................................................................................................................................... 18

2.2 REQUIREMENTS FOR INSTALLATION .................................................................................................................. 18

2.3 INSTALLING THE INVERTER ............................................................................................................................... 18

2.4 LOCATING THE INVERTER ................................................................................................................................. 19

2.5 MOUNTING THE INVERTER ................................................................................................................................ 21

2.5.1 CONTROL PANEL ORIENTATION ......................................................................................................................... 22

2.6 WIRING THE INVERTER ..................................................................................................................................... 22

2.6.1 MAKING DC WIRING CONNECTIONS .................................................................................................................... 22

2.6.2 DC GROUNDING (ON-VEHICLE) .......................................................................................................................... 24

2.6.3 DC GROUNDING (OFF-VEHICLE) ......................................................................................................................... 24

SECTION 3

OPERATION

3.1 GENERAL ......................................................................................................................................................... 25

3.2 PRINCIPLES OF OPERATION .............................................................................................................................. 25

3.3 OUTPUT WAVEFORM ......................................................................................................................................... 25

3.4 CONTROL PANEL .............................................................................................................................................. 26

3.4.1 TO OPERATE THE QUIETPOWER INVERTER: ........................................................................................................ 27

3.5 POWERSAVE MODE .......................................................................................................................................... 27

3.6 INVERTER OPERATING LIMITS AND PROTECTION FEATURES ................................................................................ 28

3.7 PERFORMANCE GRAPHS AND SPECIFICATIONS .................................................................................................. 30

3.7.1 POWER DERATING CURVE ................................................................................................................................. 30

3.7.2 EFFICIENCY CURVE .......................................................................................................................................... 31

3.7.3 TECHNICAL SPECIFICATIONS ............................................................................................................................. 32

3.8 USAGE GUIDELINES FOR THE QP-1800 .............................................................................................................. 33

Iris Technology Operator's Manual

QuietPower 1800 (QP-1800) Doc 287.F701 / 100412

Page 4 of 56 Rev 12 APR 2010

SECTION 4

TEST AND TROUBLESHOOTING

4.1 GENERAL ......................................................................................................................................................... 34

4.2 TESTING .......................................................................................................................................................... 34

4.3 TROUBLESHOOTING ......................................................................................................................................... 35

4.3.1 FAULT CONDITIONS AND INDICATORS ................................................................................................................ 35

4.3.2 TROUBLESHOOTING TIPS .................................................................................................................................. 36

SECTION 5

PREVENTATIVE MAINTENANCE

5.1 GENERAL ......................................................................................................................................................... 37

5.2 INSPECT AND CLEAN ........................................................................................................................................ 37

5.2.1 INSPECTION ..................................................................................................................................................... 37

5.2.2 CLEANING ........................................................................................................................................................ 38

5.3 NATO CABLE REPLACEMENT ............................................................................................................................. 39

5.3.1 NATO CABLE REMOVAL ..................................................................................................................................... 39

5.3.2 NATO CABLE INSTALLATION .............................................................................................................................. 40

5.4 STORAGE ........................................................................................................................................................ 41

5.5 PREPARATION FOR SHIPMENT ........................................................................................................................... 41

SECTION 6

CORRECTIVE MAINTENANCE

6.1 GENERAL ......................................................................................................................................................... 42

6.2 INSPECT AND CLEAN ........................................................................................................................................ 42

6.2.1 INSPECTION ..................................................................................................................................................... 42

6.2.2 CLEANING ........................................................................................................................................................ 43

6.3 FUSE REPLACEMENT ........................................................................................................................................ 44

6.3.1 FUSE REMOVAL ................................................................................................................................................ 44

6.3.2 FUSE INSTALLATION ......................................................................................................................................... 45

SECTION 7

WARRANTY AND SERVICE

7.1 GENERAL ......................................................................................................................................................... 46

7.2 WARRANTY ...................................................................................................................................................... 46

7.3 WARRANTY SERVICE ........................................................................................................................................ 47

Iris Technology Operator's Manual

QuietPower 1800 (QP-1800) Doc 287.F701 / 100412

Page 5 of 56 Rev 12 APR 2010

APPENDIX A

VEHICLE CONSIDERATIONS

A.1 VEHICLE ALTERNATOR ...................................................................................................................................... 48

A.2 MILITARY BATTERIES ........................................................................................................................................ 48

A.3 LOAD AND RUNTIME.......................................................................................................................................... 50

APPENDIX B

TECHNICAL ADDENDUM

B.1 QP-1800 PERFORMANCE WITH VEHICLE AND ENVIRONMENTAL FACTORS ............................................................ 51

B.1.1 TEMPERATURE EFFECTS ON BATTERY PERFORMANCE ....................................................................................... 51

B.1.2 AGE AND CONDITION OF THE VEHICLE BATTERY ................................................................................................. 52

B.1.3 CONDITION AND INTEGRITY OF THE VEHICLE CABLING ........................................................................................ 52

B.1.4 LOOSE CONNECTIONS ...................................................................................................................................... 52

B.2 OPERATION WITH SURGE SUPPRESSION POWER STRIPS ..................................................................................... 52

B.3 OPERATION WITH DOWNSTREAM EMC COMPONENTS .......................................................................................... 52

B.4 FREQUENTY ASKED QUESTIONS (FAQS). ............................................................................................................ 53

LIST OF FIGURES

FIGURE 1: FRONT PANEL OF THE QP-1800 ........................................................................................................ 17

FIGURE 2: REAR PANEL OF THE QP-1800 .......................................................................................................... 17

FIGURE 3: APPROVED MOUNTING ORIENTATIONS OF THE QP-1800 ..................................................................... 21

FIGURE 4: CONTROL PANEL ROTATION AND ATTACHMENT .................................................................................. 22

FIGURE 5: INVERTER NATO CABLE .................................................................................................................... 22

FIGURE 6: VEHICLE GROUNDING REQUIREMENTS FOR THE QP-1800 ................................................................... 24

FIGURE 7: QUIETPOWER INVERTER TRUE SINE WAVE OUTPUT ............................................................................ 25

FIGURE 8: QP-1800 CONTROL PANEL ................................................................................................................ 26

FIGURE 9: OUTPUT POWER (W) DERATING CURVE .............................................................................................. 30

FIGURE 10: EFFICIENCY (%) AND HEAT DISSIPATION (W) .................................................................................... 31

FIGURE 11: INVERTER COVER REMOVAL ........................................................................................................... 45

FIGURE 12: FUSE REMOVAL AND REPLACEMENT. ............................................................................................... 45

FIGURE 13: RUNTIME HOURS VS AMPS OVER TEMPERATURE .............................................................................. 51

FIGURE 14: ENERGY FLOW ............................................................................................................................... 54

LIST OF TABLES

TABLE 1: QUIETPOWER SYSTEM AND COMPONENT PARTS LIST ........................................................................... 14

TABLE 2: OPERATING LIMITATIONS .................................................................................................................... 28

TABLE 3: SYSTEM TRIP VOLTAGES .................................................................................................................... 28

TABLE 4: TECHNICAL SPECIFICATIONS ............................................................................................................... 32

TABLE 5: FAULT CONDITIONS AND INDICATORS .................................................................................................. 35

TABLE 6: TROUBLESHOOTING TIPS .................................................................................................................... 36

TABLE 7: INSPECTION (EXTERNAL) .................................................................................................................... 37

TABLE 8: CLEANING (EXTERNAL) ....................................................................................................................... 38

TABLE 9: INSPECTION (INTERNAL) ..................................................................................................................... 42

TABLE 10: CLEANING (INTERNAL) ...................................................................................................................... 43

TABLE 11: COMPARISON OF MILITARY BATTERY SPECIFICAITONS ........................................................................ 49

TABLE 12: SAMPLE LOAD AND RUNTIME TABLE .................................................................................................. 50

Iris Technology Operator's Manual

QuietPower 1800 (QP-1800) Doc 287.F701 / 100412

Page 6 of 56 Rev 12 APR 2010

Symbols and Conventions

The following conventions are used in this manual to communicate hazards to the operator, device or associated

equipment that may occur with improper installing, operating, maintaining and servicing this equipment. These

symbols are also used to make the operator aware of the inherent and potential hazards associated with this type of

equipment.

- NOTE -

Provides useful additional information for the user.

CAUTION

The hazard may result in minor or moderate damage to equipment and

may render it inoperative.

WARNING

A POTENTIALLY HAZARDOUS SITUATION WHICH, IF NOT AVOIDED, COULD

RESULT IN DEATH OR SERIOUS INJURY.

Iris Technology Operator's Manual

QuietPower 1800 (QP-1800) Doc 287.F701 / 100412

Page 7 of 56 Rev 12 APR 2010

Specific Warnings and Hazards of this Device

The following are specific warning, cautions and hazards related to the installation, use,

maintenance and service of this device.

WARNING

FIRE AND SHOCK HAZARD. MAKE SURE THE CABLE IS

DISCONNECTED FROM 24 VDC POWER SOURCE PRIOR TO INSTALLING

CABLE ONTO INVERTER TERMINALS. FAILURE TO DISCONNECT

CABLE FROM 24 VDC POWER SOURCE (NATO PLUG) FIRST MAY

RESULT IN FIRE, SEVERE ELECTRIC SHOCK, OR DEATH.

WARNING

BEFORE MAKING CONNECTIONS, ROUTE THE POSITIVE AND

NEGATIVE BATTERY WIRES DIRECTLY TO THE DC CONNECTION

TERMINALS ON THE QUIETPOWER INVERTER FIRST.

WARNING

SHOCK HAZARD. MAKE SURE GROUND CONNECTIONS ARE

MAINTAINED BETWEEN THE INVERTER, VEHICLE, AND GROUND ROD

(IF APPLICABLE). FAILURE TO DO SO COULD RESULT IN A POTENTIAL

SHOCK HAZARD.

WARNING

DO NOT DISASSEMBLE THE QUIETPOWER INVERTER. ONLY

QUALIFIED ELECTRONICS MAINTENANCE TECHNICIANS ARE

PERMITTED TO REPLACE THE FUSE. ATTEMPTS TO SERVICE THE

INVERTER BY UNQUALIFIED PERSONNEL MAY RESULT IN A RISK OF

ELECTRIC SHOCK OR FIRE. REFER TO SECTION 7, WARRANTY AND

SERVICE, FOR INSTRUCTIONS ON SERVICING THE INVERTER.

Iris Technology Operator's Manual

QuietPower 1800 (QP-1800) Doc 287.F701 / 100412

Page 8 of 56 Rev 12 APR 2010

WARNING

MAKE SURE INVERTER IS ELECTRICALLY DISCONNECTED FROM 24

VDC POWER SOURCE (NATO PLUG) PRIOR TO SERVICING. FAILURE

TO DISCONNECT INVERTER FROM 24 VDC POWER SOURCE (NATO

PLUG) FIRST MAY RESULT IN FIRE, SEVERE ELECTRIC SHOCK, OR

DEATH.

WARNING

DO NOT DISASSEMBLE THE QUIETPOWER INVERTER. ONLY

QUALIFIED ELECTRONICS MAINTENANCE TECHNICIANS ARE

PERMITTED TO REPLACE THE FUSE. ATTEMPTS TO SERVICE THE

INVERTER BY UNQUALIFIED PERSONNEL MAY RESULT IN A RISK OF

ELECTRIC SHOCK OR FIRE. REFER TO SECTION 7, WARRANTY AND

SERVICE, FOR INSTRUCTIONS ON SERVICING THE INVERTER.

CAUTION

Review the Important Safety Instructions found at the beginning of this

manual and read this entire section, paying particular attention to the

CAUTION and WARNING statements, before proceeding with the

installation.

CAUTION

It is recommended that you read the entire wiring instruction Section first

before attempting to wire the Inverter

CAUTION

Make sure cable is connected properly: positive (+), red wire to left post

and negative (-), black wire to right post. Connecting cable improperly

may result in internal damage to inverter.

Iris Technology Operator's Manual

QuietPower 1800 (QP-1800) Doc 287.F701 / 100412

Page 9 of 56 Rev 12 APR 2010

CAUTION

Do not disassemble the QuietPower inverter. Only qualified electronics

maintenance technicians are permitted to replace the fuse. Attempts to

service the inverter by unqualified personnel may result in a risk of

electric shock or fire. Refer to section 7, warranty and service, for

instructions on servicing the inverter.

CAUTION

Do not use harsh or abrasive cleaners on the QuietPower inverter or

NATO cable. Do not use petroleum-based products of any kind. Damage

can result if these precautions are not followed. Use only a non-abrasive

cloth dampened with soap and water to clean inverter and NATO cable.

Do not attempt to flush the unit with liquids of any kind.

CAUTION

If you are installing the NATO Cable for the first time, install the red

terminal cover on the red lead and the black terminal cover on the black

lead.

Iris Technology Operator's Manual

QuietPower 1800 (QP-1800) Doc 287.F701 / 100412

Page 10 of 56 Rev 12 APR 2010

General Safety Precautions

The following are general safety precautions that are not related to any specific procedures and

therefore do not appear elsewhere in this publication. These are recommended precautions

that personnel must understand and apply during many phases of operation and maintenance.

 Keep away from live circuits. Operating personnel must at all times observe all safety

regulations. Do not replace components or make adjustments inside the equipment with

the voltage supply turned on. Under certain conditions, dangerous potentials may exist

when the power control is in the OFF position. To avoid casualties, always remove

power and discharge. Ground a circuit before touching it.

 Do not service or adjust alone. Under no circumstances should any person reach into

or enter the enclosure for the purpose of servicing or adjusting the equipment except in

the presence of someone who is capable of rendering aid.

 Resuscitation. Personnel working with or near high voltages should be familiar with

modern methods of resuscitation. Such information may be obtained from the Red

Cross (www.redcross.org).

 Save these instructions. This Owner‟s Manual contains important safety and operating

information for the QuietPower Inverter.

 The QuietPower Inverter has a Ground Fault Circuit Interrupter (GFCI) and a Circuit

Breaker for your safety. These features are critical to the safe operation of this system

and must not be disabled.

 Do not expose the QuietPower Inverter to rain, snow, spray, bilge or dust. To

reduce risk of fire hazard, do not cover or obstruct the ventilation openings. Do not

install the QuietPower Inverter in a zero-clearance compartment. Overheating may

result.

 Do not use attachments not recommended or sold by Iris Technology. Doing so

may result in a risk of fire, electric shock, or injury to persons.

 The QuietPower Inverter is designed to connect to a military vehicle 24 VDC power

system through an available and/or supplied NATO Cable.

 Do not operate the QuietPower Inverter with damaged wiring. To avoid a risk of fire

and electric shock, make sure that existing wiring is in good electrical condition.

 Do not operate the QuietPower Inverter if it has received a sharp blow, been

dropped, or otherwise damaged in any way. If the QuietPower Inverter has been

damaged, refer to Section 7, Warranty and Service.

 Do not disassemble the QuietPower Inverter. Only qualified electronics maintenance

technicians are permitted to replace the fuse. Attempts to service the inverter by

unqualified personnel may result in a risk of electric shock or fire. Refer to Section 7,

Warranty and Service, for instructions on servicing the inverter.

 To reduce risk of electrical shock, disconnect the DC power from the QuietPower

Inverter before attempting any maintenance or cleaning or working on any

equipment and circuits connected to the QuietPower Inverter. Turning off controls

will not reduce this risk.

Iris Technology Operator's Manual

QuietPower 1800 (QP-1800) Doc 287.F701 / 100412

Page 11 of 56 Rev 12 APR 2010

Explosive Gas Precautions

 This equipment contains components which can produce arcs or sparks. To

prevent fire or explosion do not install in compartments containing batteries or flammable

materials or in locations which require ignition protected equipment. This includes any

space containing gasoline-powered machinery, fuel tanks, or joints, fittings, or other

connection between components of the fuel system.

 Working in the vicinity of a lead-acid battery is dangerous. Batteries generate

explosive gasses during normal battery operation.

 To reduce the risk of battery explosion, follow these instructions and those

published by the battery manufacturer and the manufacturer of the equipment in

which the battery is installed.

Precautions When Working With Batteries

 Do not work alone. Someone should be within range of your voice or close enough to

come to your aid when you work near a lead-acid battery.

 Have plenty of fresh water and soap nearby in case battery acid contacts skin,

clothing, or eyes.

 Wear complete eye protection and clothing protection. Avoid touching eyes while

working near batteries.

 Wear eye protection to keep corrosion from coming in contact with eyes, when

cleaning battery terminals and before making connections.

 If battery acid contacts skin or clothing, wash immediately with soap and water. If

acid enters eye, immediately flood eye with running cold water for at least 20 minutes

and get medical attention immediately.

 NEVER smoke or allow a spark or flame in vicinity of battery or engine.

 Do not drop a metal tool on the battery, nor allow metal to contact the battery

terminals or vehicle chassis. The resulting spark or short-circuit on the battery or other

electrical part may cause an explosion.

 Remove personal metal items such as rings, bracelets, necklaces, and watches

when working with a lead-acid battery. A lead-acid battery produces a short-circuit

current high enough to weld a ring or the like to metal, causing a severe burn.

Iris Technology Operator's Manual

QuietPower 1800 (QP-1800) Doc 287.F701 / 100412

Page 12 of 56 Rev 12 APR 2010

FCC INFORMATION

This equipment has been tested and found to comply with the limits for a Class B digital device,

pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable

protection against harmful interference in a residential installation. This equipment generates,

uses, and can radiate radio frequency energy and, if not installed and used in accordance with

the instructions, may cause harmful interference to radio communications. However, there is no

guarantee that the interference will not occur in a particular installation. If this equipment does

cause harmful interference to radio or television reception, which can be determined by turning

the equipment off and on, the user is encouraged to try to correct the interference by one or

more of the following measures:

 Reorient or relocate the receiving antenna.

 Increase the separation between the equipment and receiver.

 Connect the equipment into an outlet on a circuit different from that to which the receiver

is connected.

 Consult the dealer or an experienced radio/TV technician for help.

Department of Defense Product Evaluation

This equipment has been tested extensively by the Department of Defense (DoD) and is

approved and recommended for use in wheeled military vehicles. Contact Iris Technology for

details about obtaining a copy of these data (Restricted Distribution, FOUO).

Iris Technology Operator's Manual

QuietPower 1800 (QP-1800) Doc 287.F701 / 100412

Page 13 of 56 Rev 12 APR 2010

Section 1

Introduction

1.1 Introduction

Thank you for your purchase of the QuietPower 1800 Inverter. As a high quality, true sine wave

output inverter, you can expect the QuietPower Inverter to deliver exceptional performance and

give you years of dependable operation. The true sine wave AC output from the QuietPower

Inverter ensures all AC loads operating from the unit perform efficiently and correctly. Since

these loads were designed to operate from true sine wave voltage, you can expect these loads

to operate the same as if operating from grid/utility supplied power. In some cases, the true

sine wave output from the QuietPower Inverter is superior to the power supplied by your utility

company.

To get the most out of your QuietPower Inverter, carefully read and follow the instructions in this

guide. Pay special attention to the Important Safety Instructions in this guide and to the

WARNING and CAUTION statements found throughout the guide and on the product. Please

retain all packaging.

Should you have any questions before, during, or after installation, please call Iris Technology's

Customer Service Department for help.

Customer Service (Toll Free): (866) 240-9540

Customer Service (Local): (949) 975-8410

Customer Service (Fax): (949) 975-8498

Customer Service (Email): support@iristechnology.com

Record the following information for use when contacting Iris for servicing of the unit.

QuietPower Serial #: ___________________________ (Required)

Date of purchase: ___________________________ (If Available)

Contract reference: ___________________________ (If Available)

Iris Technology Operator's Manual

QuietPower 1800 (QP-1800) Doc 287.F701 / 100412

Page 14 of 56 Rev 12 APR 2010

1.2 Equipment Identification and Description

Table 1 lists the QuietPower systems and components that can be ordered. The parts you

receive depend on the part number ordered. Three different systems can be ordered, as well as

individual components. All inverter options ship with an Operator‟s Manual and Installation Kit.

The current revision of the Operator‟s Manual is downloadable from www.iristechnology.com.

Table 1: QuietPower System and Component Parts List

Iris PN / NSN

Image

Description / Components

287A120

6130-01-552-6350

QP-1800 Inverter System

NATO Cable (12 ft)

Transportation Case

287A107

6130-01-496-6456

QP-1800 Inverter

NATO Cable (12 ft)

287A101

6130-01-496-6448

QP-1800 Inverter

287A106

6150-01-497-2515

NATO Cable (12 ft)

287A108

7050-01-551-0600

Transportation Case

Outside dimensions:

22.1” x 17.9” x 10.4”

(560 x 455 x 265 mm)

Iris Technology Operator's Manual

QuietPower 1800 (QP-1800) Doc 287.F701 / 100412

Page 15 of 56 Rev 12 APR 2010

Iris PN / NSN

Image

Description / Components

287F701

QP-1800 Operator‟s Manual

TM 11460A-OR/1 A

PCN 500 114600 00

287A109

Installation Kit

Replacement Fuse (1)

Battery Terminal Covers (2)

Vibration Isolators (4)

287A125

Vehicle Mounting Plate

for use with HMMWV

2870128 (EA)

5920-01-562-3354

Replacement Fuse

Littlefuse Mega 125 (125 A)

PN / MEG 125 (EA)

Fuse replacement requires a

Qualified Electronics Technician

2870140 (SET)

2870136 (BK)

2870137 (RD)

Battery Terminal Cover (SET)

Straight Clamp, 3/0 AWG

BK (Negative) PN / 4271 (EA)

RD (Positive) PN / 4272 (EA)

2870140 (SET)

2870110 (EA)

Vibration Isolators (SET)

Neoprene Cylindrical Mount

M/F, 1/4"-20, 1" Ht, 1" Wd

Iris Technology Operator's Manual

QuietPower 1800 (QP-1800) Doc 287.F701 / 100412

Page 16 of 56 Rev 12 APR 2010

1.3 Inverter Key Features

The QuietPower Inverter utilizes advanced high frequency switching technology in the power

conversion process. The circuits are similar to those used in power supplies for computers and

other electronic equipment. This technology offers several benefits:

 Light weight: for easy installation

 Pure sine wave output: for reduced interference

 High surge capability: for „hard-to-start” AC loads

 High frequency switching: for nearly silent operation

Refer to paragraph 3.7, Performance Graphs and Specifications, for complete specifications.

1.3.1 Inverter Function

When connected properly and the power switch is turned to the „I‟ (On) position, the QuietPower

Inverter draws power from the 24 VDC (nominal) battery and/or vehicle electrical bus and

delivers a true sine wave 115 VAC (nominal @ 15 A) output. As long as the input voltage is

maintained within the operating range of the unit, the QuietPower will continue to deliver AC

power to the loads connected. High and low battery shutdowns will engage if the battery

voltage falls out of the specified range of operation (20-32 VDC).

1.3.2 Control Panel

The Control Panel provides Off/On („O/I‟) control and displays operating information so you can

monitor the status of the Inverter and your batteries.

This panel can be removed and re-attached in different orientations so the display information is

directed at you in the most convenient fashion for all recommended mounting configurations.

The procedure to rotate the panel is found in section 2.5.

Iris Technology Operator's Manual

QuietPower 1800 (QP-1800) Doc 287.F701 / 100412

Page 17 of 56 Rev 12 APR 2010

Figure 1: Front Panel of the QP-1800

Figure 2: Rear Panel of the QP-1800

Circuit

Breaker

GFCI

(Ground Fault

Circuit Interrupter)

Off/On

(O/I)

Control

Panel

LCD

Display

Duplex (AC)

Outlet

Serial

Number

Ground

Lug

Isolators (4)

(Not Shown)

Input

Terminals (2)

Iris Technology Operator's Manual

QuietPower 1800 (QP-1800) Doc 287.F701 / 100412

Page 18 of 56 Rev 12 APR 2010

Section 2

Installation

CAUTION

Review the Important Safety Instructions found at the beginning of this

manual and read this entire section, paying particular attention to the

CAUTION and WARNING statements, before proceeding with the

installation.

2.1 General

This section contains instructions for installing the QuietPower Inverter. After installing the unit

and making wiring connections, DO NOT turn the unit on. Proceed to Section 3, Operation,

which provides operating instructions.

2.2 Requirements for Installation

You will need the following tools and hardware to properly install the QuietPower Inverter:

 Wrench for DC terminals (½” or 13 mm)

 Wrench for Vibration Isolators (optional, 7/16”)

2.3 Installing the Inverter

Install the inverter as follows:

1. Find a suitable location to install the QuietPower Inverter. Refer to paragraph 2.4,

Locating the Inverter, for more information.

2. Install the inverter. Refer to paragraph 2.5, Mounting the Inverter, for more

information.

Iris Technology Operator's Manual

QuietPower 1800 (QP-1800) Doc 287.F701 / 100412

Page 19 of 56 Rev 12 APR 2010

WARNING

FIRE AND SHOCK HAZARD. MAKE SURE THE CABLE IS

DISCONNECTED FROM 24 VDC POWER SOURCE PRIOR TO INSTALLING

CABLE ONTO INVERTER TERMINALS. FAILURE TO DISCONNECT

CABLE FROM 24 VDC POWER SOURCE (NATO PLUG) FIRST MAY

RESULT IN FIRE, SEVERE ELECTRIC SHOCK, OR DEATH.

CAUTION

Make sure cable is connected properly: positive (+), red wire to left post

and negative (-), black wire to right post. Connecting cable improperly

may result in internal damage to inverter.

3. Install the NATO Cable to the inverter first and then to the 24 VDC power source.

Refer to paragraph 2.6, Wiring the Inverter, for more information.

4. Before turning the inverter on, refer to Section 3, Operation.

Iris Technology makes available a vehicle mounting plate for use with the Expanded-Capacity

HMMWV Fleet or HMMWV (ECV) which have Air Conditioning installed (PN 287A125). This

plate allows for direct bolt-on attachment without vehicle modification. A DoD/USMC

Modification Instruction (MI) exists that details the instructions for mounting this plate for

HMMWV (ECV) installation. (MI 11460A-OI/1)

2.4 Locating the Inverter

The QuietPower Inverter utilizes complex electronic circuits and although design precautions

have been made for protection of these circuits, they can be susceptible to damage from use in

extreme environments. The QuietPower Inverter should only be installed in a location that

meets the following requirements:

 Dry: do not allow water or other fluids to drip or splash on the QuietPower Inverter. Do

not mount the QuietPower Inverter in an area subject to splashing or dripping water or

bilge.

 Cool: normal ambient air temperature should be between -20°C (-4° F) and +60° C

(+140° F) - the cooler the better within this range. Refer to the operating temperature

information in paragraph 3.7.3.

 Ventilated: allow at least 5 inches (13 cm) of clearance around unit. Ensure the

ventilation openings on the unit are not obstructed. If mounting in a compartment,

ventilate with louvers or cut-outs.

Iris Technology Operator's Manual

QuietPower 1800 (QP-1800) Doc 287.F701 / 100412

Page 20 of 56 Rev 12 APR 2010

 Safe: DO NOT install the QuietPower Inverter in the same compartment as batteries or

in any compartment capable of storing flammable liquids such as gasoline. DO NOT

install the QuietPower Inverter in an engine compartment or other location where ignition

protected equipment is required.

 Dust-free: DO NOT install the QuietPower Inverter in a dusty environment where dust,

wood particles or other filings/shavings are present. These can be pulled into the unit

when the cooling fan is operating.

 Avoid the use of AC extension cord(s) wherever possible. If extension cords must

be used, they must be three (3) conductor cords (grounded) and must be suitable for the

circuit current (20A).

 Install QuietPower Inverter close to battery/batteries: avoid excessive cable lengths

but DO NOT install the QuietPower Inverter in the same compartment as batteries. Use

the recommended wire lengths and sizes (refer to paragraph 2.6, Wiring the Inverter).

DO NOT mount the QuietPower Inverter where it will be exposed to the gases produced

by the battery. These gases are very corrosive and prolonged exposure will damage the

QuietPower Inverter.

 Protected from battery acid: Never allow battery acid to drip on the QuietPower

Inverter or its wiring when reading specific gravity or filling the battery.

The remainder of this page is intentionally left blank

Page is loading ...

IRIS QuietPower 1800 User manual

Brand: IRIS

Model: QuietPower 1800

Category: Power adapters & inverters

Type: User manual

Download PDF

report

IRIS QuietPower 1800 User manual

IRIS QuietPower 1800 User manual

Related papers

Other documents