2. Bodet
  3. BTX8020
BTX8020

Bodet BTX8020 User manual

  • Hello! I've reviewed the provided document for the Bodet BTX8020 SET and BTX8020 SET Scoreapp scoreboards. This manual details the setup, usage, and technical specifications of these scoreboards, including instructions for different installation methods and control options using either a Scorepad keyboard or the Scoreapp application. I'm ready to answer any questions you might have about these devices.
  • What sports can the BTX8020 SET scoreboard be used for?
    How is the BTX8020 SET scoreboard powered?
    How can the BTX8020 SET Scoreapp scoreboard be controlled?
1
BODET Time & Sport
1 rue du Général de Gaulle
49340 Trémentines I France
Tél: +33 241 71 72 33
Réf.: 608665 B
www.bodet-sport.com
BTX8020 SET
Upon receipt, always check the product for damage during shipment.
If any is found, you may file a damage claim with the carrier
Installation and operating instructions
2
Table of contents
1. Electrical and mechanical safety standards 3
2. Installation 4
2.1 Checking the equipment 4
2.2 Presentation 4
2.3 Mechanical installation 4
2.4 Electrical connection 6
3. Commissioning 7
3.1 BTX8020 SET (Ref. 916 091) 7
3.2 BTX8020 SET Scoreapp (Ref. 916 092) 9
3.3 Dip-switch settings 9
4. Use 9
4.1 BTX8020 SET (Ref. 916 091) 9
4.2 BTX8020 SET Scoreapp (Ref. 916 092) 9
5. Technical features 10
3
1. Electrical and mechanical safety standards
We recommend that you read this manual carefully before installing the product.
Failure to observe these instructions may cause irreversible damage and invalidate the warranty.
BODET shall not be responsible for any damage arising due to non-observance of these instructions.
Identification of pictograms :
Symbol Description
IEC60417 - 1641
Operating instructions
IEC60417 - 6172
Disconnection, all power plugs
IEC60417 - 5019
Protective earth (ground)
IEC60417 - 0434b
Caution
IEC60417 - 5032
Alternating current
IEC60417 - 6414
Waste Electrical and Electronic Equipment
(WEEE)
IEC60417 - 6042
Caution, risk of electric shock
INSTALLING THE PRODUCT
This equipment must be tted and maintained by a qualied person.
Electrical installation :
The scoreboard must be powered through the building’s electrical installation. It is designed for Category II overvoltage. Max. V
peak: 2500V.
Provide a mains power supply protection compliant with CEI 61643 in other cases, if necessary. The electrical installation of this
equipment must comply with the rules laid down in the standards in force in the country where the product is used.
The installation must comply with the IEC 364 standard.
Provide a dierential circuit breaker max. 30mA / phase-neutral of 16A maximum, rapidly accessible upstream from each pow-
er-supply line (permanent power supply for the scoreboard).
This circuit breaker provides power supply protection and disconnecting, and must be cut o in the event of maintenance.
Conductors on the same circuit must be attached to each other close to the terminal block to avoid reduced isolation should one
of the terminals become loose.
The equipment should not be powered up until it has been mounted to the wall. The scoreboard must be closed.
4
2. Installation
2.1 Checking the equipment
BTX8020 SET (Ref. 916091) :
- Scoreboard BTX8020 SET.
- Installation and operating instructions.
BTX8020 SET Scoreapp (Ref. 916092) :
- Scoreboard BTX8020 SET.
- Installation and operating instructions.
- Box Scoreapp (installed inside the scoreboard BTX8020 SET).
2.2 Presentation
A Display per sport: 5 red digits of 20 cm per team.
- Tennis and Padel : sets, games and points.
- Badminton and Squash : sets and points.
- Volleyball and Table tennis : number of sets won and points in the current set.
B Service indicator : 1 red dot Ø36 mm per team or player.
C Stickers A and B for teams or players identication.
CAUTION: The maximum distance for communication by HF control between the keyboard and the
scoreboard is 100 meters in open eld.
2.3 Mechanical installation
Wall mounting
Attach the scoreboard to the wall using 4 screws Ø8 mm and suitable wall plugs (not supplied) using
the 4 keyhole slots located on the rear of the BTX8020 SET scoreboard.
AB
C
620
560
2000 122
1560
Dimensions in mm
5
Post mounting (ref. 915170)
1- Pour two blocks of concrete for the two posts with the help of the jigs (915196).
Dimensions of two blocks of concrete :
L = 75 cm - I = 75 cm - P = 75 cm
2- Seal the 8 anchor bolts (915178) in each block (4 anchors per block) and then tighten the nuts.
Make sure you carefully check the spacing and height of the anchor bolts.
Nut HU M16
Bent anchor bolt M16
A
Flat washer M16
B
Rigid insulating tube and clips
to be assembled on site
Rigid insulating PVCtube Ø20
Plate edge clips
1560
200 200
Upright post
B
3365
A
220
100
6
3- Attach the panel on the 2 posts with the 4 clamps and the threaded rods (B)
2.4 Electrical connection
Connect the scoreboard’s power supply to a mains outlet.
Mains outlet.
125
113
1560
Dimensions in mm
B
Flange
Threaded rod
Cable cover
7
3. Commissioning
3.1 BTX8020 SET (Ref. 916 091)
The Scorepad keyboard is not included with reference 916 091, it must be ordered separately.
HF INSTALLATION
From the Scorepad keyboard :
1- Scorepad homepage, click .
2- Click the Technician menu (code : 4934).
3- Select the Communication menu.
4- Click one of the previously created congurations.
5- Click Communication type.
6- Select HF.
The link between the Scorepad and the BTX8020 SET scoreboard is made by the 868MHz HF
modem.
For this mode, the installation number and the channel number must be congured.
BTX 8020 SET
No. installation: 1
No. scoreboard: 1
Scorepad
Scoreboard : BTX 8020 SET
No. installation: 1
No. Channel: 1
8
WIRED INSTALLATION
From the Scorepad keyboard :
1- Scorepad homepage, click .
2- Click the Technician menu (code : 4934).
3- Select the Communication menu.
4- Click one of the previously created congurations.
5- Click Communication type.
6- Select Wired.
Connect the Scorepad to the BTX8020 SET scoreboard:
1- Unscrew the 4 cross-headed screws on the right side
of the BTX8020 SET to remove them :
2- Slide the glass to the right.
/!\ Do not press on the glass as this may damage the LEDs.
3- Unscrew the middle LED module on the second line:
4- Connect the keyboard cable to the MDM terminal block (RT+:
white / Brown: RT-):
5- Put back the glass and side panel in place by carrying out steps 1 and 2 in reverse order.
230VAC
916014 :
Keyboard/connection box cable + DIN wall outlet
Scorepad
9
3.2 BTX8020 SET Scoreapp (Ref. 916 092)
The Scoreapp box is factory installed and connected inside the BTX8020 SET
scoreboard.
No installation action is required after connecting the mains power supply to the BTX8020 SET
scoreboard (see paragraph 2.4 Electrical connection).
3.3 Dip-switch settings
The dip-switch setting is only necessary if you want to use two (or more) BTX8020
SET scoreboards.
Refer to the «Bodet scoreboard installation guide» for :
- DIP-switch settings for an installation with several BTX8020 SET scoreboards.
- Test the display of the BTX8020 SET scoreboard(s) and the Scorepad keyboard.
4. Use
4.1 BTX8020 SET (Ref. 916 091)
Use from the Scorepad keyboard.
Download the practised sport’s manual from the following link or by scan-
ning the QR code.
https://www.bodet-sport.com/support/documents-database/scorepad.html
4.2 BTX8020 SET Scoreapp (Ref. 916 092)
Use from the Scoreapp application.
Download the Scoreapp manual from the following link or by scanning
the QR code. (see from page 4).
https://www.bodet-sport.com/support/scoreapp.html
10
5. Technical features
Weight............................................. 20 kg
Construction.................................. Aluminium with protective glass
Protection index............................. IP54 - IK07
Optimal viewing distance.............. From 60 to 90 meters
Reading angle................................. 160°
Power supply.................................. 100-240 VAC 50/60Hz
Consumption.................................. 40 W
Electric protection.......................... Circuit breaker 16A
Operating temperature.................. -20°C to +50°C
/