Page is loading ...
S PEC F ILE
ET-PKF100S
Ceiling mount bracket
As of October 2008 < 1 >
Specifications Vertical correction angle: +5°, -15°
Horizontal slant correction angle: ±5°
Horizontal turn correction angle: ±5°
Dimensions (W x H x D): 435 x 210 x 245 mm (17-1/8˝ x 8-9/32˝ x 9-21/32˝)
Note: Height (H) include holding brackets.
Weight: 1.9 kg (4.2 lbs)
Parts Attachment plate . . . . . . . . . . . . . . . . . . . . . . . 1
Projector mount bracket . . . . . . . . . . . . . . . . . . 1
Holding bracket A . . . . . . . . . . . . . . . . . . . . . . 1
Holding bracket B . . . . . . . . . . . . . . . . . . . . . . 1
Washer-fitted screws (M4 x 12) . . . . . . . . . . . . 8
Wire rope . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Flat wire clip . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Clamp tube . . . . . . . . . . . . . . . . . . . . . . . . . . . .2
Weights and dimensions shown are approximate. Specifications subject to change without notice.
unit : mm (inch)
NOTE: This illustration is not drawn to scale.
Description
This ceiling mount bracket is to be used when mounting LCD projectors to the low ceiling.
Caution:
• Mounting should be done by a qualified technician.
• Make sure that the mounting (ceiling) area has sufficient strength.
• Read the enclosed mounting instructions thoroughly before starting.
• When the product is no longer going to be used, have it disposed of quickly by a professional
disposal service.
• Do not use an electric screwdriver or impact driver to tighten screws. (Use a torque driver or simi-
lar tool.)
10°
10°
15°
70
Attachement
plate
65 (2-9/16˝)
(2-3/4˝)
25
(31/32˝)
166.5
(6-9/16˝)
432
(17˝)
189
(7-7/16˝)
436 (17-5/32˝)
9.5 (3/8˝)
13 (1/2˝)*
3-Ø9.5 (3/8˝)
20 (2-9/16˝)
From center of
rotation to center
of lens
*
Ø8.5
(11/32˝)
150 (5-29/32˝)
160 (6-5/16˝)
153
(6-1/32˝)
210
(8-9/32˝)
140 (5-1/2˝)
114 (4-1/2˝)
130 (5-1/8˝)
104 (4-3/32˝)
5°
Attachment plateIllustration shows the bracket attached to the
PT-F300NT/F300/FW300NT/FW300.
unit : mm (inch)
NOTE: This illustration is not drawn to scale.
Dimensions
S PEC F ILE
ET-PKF100S
Ceiling mount bracket
As of October 2008 < 2 >
195
10°
10°
Ø49
Ø43
(1-15/16˝)
70
Projector
Attachement plate
369– 449
(14-17/32˝–17-11/16˝)
Adjus table in
20 mm (25/32˝) s teps
65 (2-9/16˝)
(2-3/4˝)
(1-11/16˝)
(7-11/16˝)
176
(6-15/16˝)
432
(17˝)
435 (17-1/8˝)
13 (1/2˝)
3-Ø9.5 (3/8˝)
Ø8.5(11/32˝)
20 (2-9/16˝)
150 (5-29/32˝)
160 (6-5/16˝)
140 (5-1/2˝)
110 (4-11/32˝)
130 (5-1/8˝)
100 (3-15/16˝)
Attachment plateIllustration shows the bracket attached to the
PT-F200NT/F200.
unit : mm (inch)
NOTE: This illustration is not drawn to scale.
Dimensions
/