Gianni Industries EB195TGVGL Installation guide

Brand: Gianni Industries

Model: EB195TGVGL

Type: Installation guide

This manual is also suitable for

Pull in: 0.9A/12V; 0.45A/24V

EB180

EB185

EB190TG

EB195TG

Holding: 0.15A/12V; 0.1A/24V

EB185 / EB195TGEB180/EB190TG

001

941

012

EB180/190 Series Electric Dropbolt Installation Instructions

Features Specifications

Horizontal or vertical installation

Energy saving design

Intelligent electronics

Vandal resistant circuit design

Relock time delay (Selectable from 0, 3, 6, 9 seconds)

Push button trigger input (For TG series)

Models

12/24 VDCOperating Voltage

Current Draw

Bolt Status Sensor Output

Door Position Status Output

Relock Time Delay

Push Button Trigger Input

Intelligent Electronics & Energy Saving Design

All models are designed with intelligent logic circuit allowing the bolt to

keep retracting until the door is properly closed.

A. When the swing-through door is closed, the relock delay time begins

and the reed switch in the lock detects the sensor magnet in the strike

plate.

B. The bolt projects after relock delay time expires and keeps projecting

until the door is closed in the correct position and locked.

C. After the bolt is projected to lock the door, the current draw will drop

to the normal state.

D. The reed switch will automatically switches off at the same time when

the door is locked.

Mortise Mount

Surface Mount (-S Model)

EB180, EB185

EB190TG, EB195TG

EB195TGS EB195TGVGL

Glass Mount (-VGL Model)

B. Pull in

C. Holding D.

Time (seconds)

Current Draw (mA)

Dimensions (Mortise Mount)

Unit: mm

Series

For double or single action doors

201

212

53.5

102

53.5

Mortise Mount Installation (For Hollow Metal Doors)

Please refer to the particular template for each specific

cutting size and location to drill the screw holes.

Installation Instructions

Ensure that the door frame can accommodate the lock

body. Also check if it is possible to place the wires inside

the door frame.

Ensure that the double action door swings back to the correct

position so the dropbolt can lock up immediately.

Check if the regulated power supply or controller provides the

correct current draw (Pull-in current: 0.9A/12VDC, holding

current: 0.3A/12VDC).

Dimensions (Surface Mount)

EB195TGS

EB195TGVGL

(For full glass doors)

Warning:

1. The connection of an incorrect voltage may result in damage

and is not covered by the product warranty.

Mortise cutout in tube

Attach fixing lugs Connect the power

Assemble the lock and test it

Unit: mm

2. Select the appropriate power supply cable to ensure if the

lock receives sufficient power to operate.

3. This product has been designed for use in weather protected

areas and normal circumstances, hence it does not require

any maintenance. DO NOT OIL OR LUBRICATE

4. This product must be used in conjunction with a quality floor

spring or door closer to ensure positive realignment on closing.

Installation Instructions

1. Make sure the installation location and clean the surface of

glass.

2. Take off the sticker on the back of the spacer and attach the

spacer to glass. Each VGL bracket is 14mm width and spacer

is 1mm thickness. Add more spacers if needed according to

glass thickness. Use silicon to secure the VGL bracket firmly.

3. Tighten the set screws with the Allen wrench, secure the dropbolt

to the glass bracket, and then install the cover.

Caution:

1. It is suggested to attach the spacer to the inside of the door.

2. Tighten the set screws lightly to prevent breaking the glass.

Surface Mount Installation (For EB195TGS)

Header

Lock Body

Blind Nut

M6 x40 Screw

Door

Leaf

Door

Leaf

Strike Plate

Header

Blind Nut

Ins

Glass Mount Installation (For EB195TGVGL)

Set Screw

Ins

Set Screw

Glass thickness

is 10 or 12mm

ss Gla

Doo

3 4 5

Installing Blind Nuts

Blind Nut Assembly

Blind nut

Nut

Washer

Hex screw

Drill a 9.4mm hole and hammer the

blind nut assembly into the hole.

Allen wrench

Use a wrench or vice-grip to tightly

hold the nut. Then use the included

Allen wrench to slowly tighten the

screw until it does not turn any

further.

This compresses the blind nut so

that it remains permanently fixed

in the hole.

Remove the installation tool from

the blind nut. Repeat step 2

through 4 for the other blind nuts.

Installation

tool

Trouble Shooting

Problem Possible Cause Solution

Dropbolt is not activated

when the door is closed

Bolt keeps projecting

Bolt cannot retract

The gap between the strike plate

and the dropbolt is large

Low voltage /current

Low voltage/current

Dropbolt is not locked properly

Strike plate is misaligned

Change the sensing range to less than 5mm.

Check the output voltage and the current draw.

(Pull-in current: 0.9A/12VDC)

Check the output voltage and the current draw.

(Pull-in current: 0.9A/12VDC)

Adjust the door closer or the door hinge so that the

door is closed in the correct position.

Use on single action doors If the door hinge

cannot be adjusted.

Move or sway the door to release the bolt to open the door.

Use on single action doors If the door hinge cannot be adjusted.

Connecting Diagrams

Caution:

Make sure that the “+” and “-” wires are connected correctly. Failure to observe polarity will result in a short circuit and is not covered

by product warranty.

EB190TG/EB195TG EB180/EB185

Crimp connectors are provided to make wiring connections easier

and more reliable. To install the connectors:

1. Insert the wires into the connector.

2. Use a crimping tool or pliers to evenly press down on the head

of the connector.

Installing the Crimp Connectors:

Power

supply

Access Control(s)

Bolt status sensor output

Rating: 3A/30VDC

Door position status output

Rating: 0.25A/30VDC

Push Button

Trigger Input (N.O.)

Trigger

Relock Time Setting

0 second 3 seconds 6 seconds 9 seconds

Power

supply

Bolt status sensor output

Rating: 3A/30VDC

Relock Time Setting

0 second 3 seconds 6 seconds 9 seconds

Access Control(s)

Gianni Industries EB195TGVGL Installation guide

Brand: Gianni Industries

Model: EB195TGVGL

Type: Installation guide

This manual is also suitable for

Download PDF

report

Gianni Industries EB195TGVGL Installation guide

This manual is also suitable for

Gianni Industries EB195TGVGL Installation guide

Related papers

Other documents