Ancona AN-4376 User manual

Type
User manual

This manual is also suitable for

© ®
Single Handle Pull-out Kitchen Faucet
STANDARDS
Tools:
Helpful Information
Flow Rate Chart
Rivella
2019-23-09 MAAN4376-1
Gather the necessary tools as shown below to complete the installation of
this faucet. Some may not be needed depending on the model of faucet you
are installing. Check with your local hardware store on the requirements of
your installation situation.
PLUMBERS PUTTY FLASHLIGHT BASIN WRENCH
SAFETY GLASSES SCREWDRIVER
PLIERSCHANNELLOCKS ADJUSTABLE WRENCH
HEX-KEY TAPE
SEALED-TUBE
Please keep the tools for future use!
WARNING:
Attention:
Important
For easy installation, you will need:
- To read all the installation instructions completely before beginning.
- To read all the warning, attention and maintenance information.
- To purchase the proper supply lines.
Tighten connection with two wrenches to prevent
damage to tube body. Be careful not to bend the
stem as this will void the product warranty.
1
2
Ø1.4-1.5"
(3.6-3.8 cm)
2 9/16 - 24 UNEF-2B
M15X1
1.3" (3.5 cm)
1.8"
(4.8 cm)
4.25"
(10.8 cm)
5.2"
(13.3 cm)
Ø 2.2"
(5.8 cm)
4.25"
(10.8 cm)
10.4"
(26.5 cm)
Ø 1.8"
(4.8 cm)
Ø 1.1"
(3 cm)
15.5"
(39.5 cm)
16.25"
(41.3 cm)
7.75"
(19.7 cm)
8.8"
(22.4 cm)
10.3"
(26.3 cm)
12°
Tools might be applied to the following places:
Installation size map Faucet Installation
Position the faucet in order on the counter top as
shown. Don't forget the O-ring. Assemble
gasket assembly and lock nut to faucet threaded
sleeve by hand and tighten the screws with
screwdriver.
Connect the shower hose to quick
connect. CAUTION: MAKE SURE
THE HOSE IS PROPERLY
ENGAGED AND SECURED IN THE
QUICK CONNECT.
Disassemble the weight and put it on
the shower hose. Then fix screws with
screwdriver.
10.7” (27.2 cm)
Checking and Testing
Test Faucet Installation
Maintenance:
3
4
5
Connect to water supply lines with either:
(A) 3/8” O.D. copper tubing (ball nose
risers with the coupling nuts) or;
(B) 3/8” copper tubing (no ball) with
supplied tube head interior connector or;
(C) IPS faucet connectors (1/2”).
Remove the shower by hand. Turn the
faucet handle all the way on, turn on hot
and cold water supply and flush water
lines for one minute. Reinstall shower
by hand.
Check all connections at arrows for
leaks and retighten if necessary. BUT
DON'T OVERTIGHTEN.
A. Move handle into "OFF" position.
B. Turn on water supplies. Check connections for leaks.
C. Remove hand shower and let both hot and cold water
run for one minute. This will help clean any debris that
might otherwise clog the system. Replace hand shower.
D. Operate handle up and down, in cold and hot positions,
to flush water lines thoroughly.
Simply rinse the surface with clear water or
mild liquid detergents (if necessary). Dry the
faucet with a clean soft cotton cloth. Do not
use any cleaning agents containing acids
polish abrasives or harsh cleaners.
A. B. C.
Parts list
Body
Cartridge base
Cartridge sleeve
Cartridge
Fixing cartridge nut
Trim cap
Index
Screw
Handle
O-ring
Washer
Screw cap
Spout
Shower sleeve
Shower head
Pull-out flexible hose
Flexible hose (red)
Flexible hose (blue)
Outlet flexible hose
Non-returnable valve
Quick connect
Base
O-ring
Connector
Washer
Plate
Nut
Threaded pipe
Screw
Pull-out sleeve
Weight
Allen key
Quick connect base
Sponge plate
Deck plate
Gasket
Screw
Plastic nut
Aerator wrench
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
PART NAMENO.
1. Clean it with water and dry it with soft cloth.
2. Clean the product with gentle liquid or glass cleaner.
3. Don't use acid cleaner.
4. Don't clean with abrasive material, abrasive paper or knife.
Cleaning and care
Daily cleaning and care are required in order to keep the product shining and working properly.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4

Ancona AN-4376 User manual

Type
User manual
This manual is also suitable for

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI