Ancona AN-4340 User manual

Type
User manual

This manual is also suitable for

The Ancona AN-4340 is a lavatory bathroom faucet that is designed for easy installation and features a sleek, modern design that will complement any bathroom décor. The faucet has a 1.2 gpm/4.5 L/min flow rate and comes with all the necessary hardware for installation, including a basin wrench, screwdriver, and adjustable wrench. The faucet also features a sealed-tube hex-key for easy maintenance and a variety of connection options, including 1/2” IPS faucet connections and 3/8" O.D. ball-nose risers.

The Ancona AN-4340 is a lavatory bathroom faucet that is designed for easy installation and features a sleek, modern design that will complement any bathroom décor. The faucet has a 1.2 gpm/4.5 L/min flow rate and comes with all the necessary hardware for installation, including a basin wrench, screwdriver, and adjustable wrench. The faucet also features a sealed-tube hex-key for easy maintenance and a variety of connection options, including 1/2” IPS faucet connections and 3/8" O.D. ball-nose risers.

© ®
Deck Lavatory Bathroom Faucet
STANDARDS
Tools:
PLUMBERS PUTTY FLASHLIGHT BASIN WRENCH
SAFETY GLASSES SCREWDRIVER
PLIERSCHANNELLOCKS ADJUSTABLE WRENCH
TAPE
Attention:
Helpful Information
Important
Arezzo
2020-03-13 MAAN4340-2
SEALED-TUBE
ASME A112.18.1/CSA B125.1
ASME A112.18.2/CSA B125.2
LISTED IAPMO/cUPC
Gather the necessary tools as shown below to complete the installation of
this faucet. Some may not be needed depending on the model of faucet you
are installing. Check with your local hardware store on the requirements of
your installation situation.
For easy installation, you will need:
- To read all the installation instructions completely before beginning.
- To read all the warning, attention and maintenance information.
- To purchase the proper supply lines.
Tighten connection with two wrench to prevent
damage to tube body. Be careful not to bend the
stem as this will void the product warranty.
Connect to water supply lines with either
risers with the coupling nuts or
A. B.
1.2 gpm/4.5 L/min
HEX-KEY
Please keep the tools for future use!
WARNING:
Faucet Installation
1
2
Tools might be applied to the following places:
Installation size map
Place the faucet and gasket on the basin.
Underneath the basin, assemble the washer and
lock nut, and tighten the lock nut by hand.
If the basin is uneven, please use silicone
under the gasket.
Connect the supply lines to the faucet
and secure the nuts with an adjustable
wrench.
Warning: Supply line #1 is for hot
water, supply line #2 is for cold
water, don't mix up.
HOT
COLD
9.9 in. (25.2 cm)
1.6 in.
(4.2 cm)
3.75 in. (9.6 cm)
1.1 in.
(3 cm)
Max.
3.8 in.
(9.7 cm)
1/2-14NPSM
6.1 in. (15.5 cm)
6.8 in.
(17.5 cm)
4 in. (10.2 cm)
2.2 in. (5.6 cm)
0.8 in.
(2.1 cm)
5.75 in. (14.7 cm)
4.3 in. (11.1cm)
4.6 in.
(11.9 cm)
1.9 in. (4.9 cm)
2
1
1/2”( 13mm) IPS
Checking and Testing
Maintenance:
3
4
5
Remove the aerator by hand. Turn
the faucet handle all the way on,
turn on hot and cold water supply
and flush water lines for one
minute. Reinstall aerator by hand.
Check all connections at arrows for
leaks, retighten if necessary.
BUT DON’T OVERTIGHTEN
Simply rinse the surface with clear water or
mild liquid detergents (if necessary). Dry the
faucet with a clean soft cotton cloth. Do not
use any cleaning agents containing acids
polish abrasives or harsh cleaners.
You can use 1/2” IPS faucet
connections A, or use the coupling
nuts with 3/8" O.D. ball-nose risers B.
A B
1. Clean it with water and dry it with soft cloth.
2. Clean the product with gentle liquid or glass cleaner.
3. Don't use acid cleaner.
4. Don't clean with abrasive material, abrasive paper or knife.
Parts listCleaning and care
Daily cleaning and care are required in order to keep the product shining and working properly.
NO. PART NAME
Handle assembly1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
Lock nut
Washer
Plate
Cartridge (hot water)
Shank
Gasket
Lock nut
O-ring
Screw
Allen key
Lift rod
Spout
Washer
Aerator collar
Inlet pipe
1
14
15
16
2
3
4
5
6
7
8
9
10
11
12
13
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4

Ancona AN-4340 User manual

Type
User manual
This manual is also suitable for

The Ancona AN-4340 is a lavatory bathroom faucet that is designed for easy installation and features a sleek, modern design that will complement any bathroom décor. The faucet has a 1.2 gpm/4.5 L/min flow rate and comes with all the necessary hardware for installation, including a basin wrench, screwdriver, and adjustable wrench. The faucet also features a sealed-tube hex-key for easy maintenance and a variety of connection options, including 1/2” IPS faucet connections and 3/8" O.D. ball-nose risers.

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI