Kichler Lighting 16236AZT50 User manual

Brand
Kichler Lighting
Model
16236AZT50
Type
User manual

This manual is also suitable for

For warranty informaon please visit: hp://www.kichler.com/warranty
IS-16236-US
We’re here to help 866-558-5706
Hrs: M-F 9am to 5pm EST
Kichler 16236, 16237, 16238 Installaon Guide
LED Slim Wallpack
IMPORTANT: Read before removing xture from carton. Retain for
future reference.
SAFETY: This xture must be wired in accordance with the
NATIONAL ELECTRICAL CODE (NEC) and applicable local codes and
ordinances. A person familiar with the construcon and operaon
of the product and the hazards involved must install this product.
A qualied licensed electrician should complete all work. Proper
grounding is required for safety.
WARNING: Make certain power is OFF before installing or
maintaining xture.
RISK OF INJURY: Fixture may become damaged and/or unstable if
not installed properly.
Cauons:
Installaon Instrucons:Fixture Diagram
NOTE: Turn o electrical supply at the breaker. Follow all local
electrical codes for wiring and grounding requirements.
Tools Required: 1/8” Allen Key, Phillips Screw Driver, Wire
Strippers & Cuers
NOTE: Unpack xture and ensure that there are no damaged parts.
FCC Informaon:
RISK OF FIRE, EXPLOSION AND ELECTRIC SHOCK
• This product should be installed, inspected, and maintained by a qualied
electrician only, in accordance with the NEC (Naonal Electric Code) and all
local codes.
• Turn o electrical power before inspecon, installaon or removal.
• Use only UL (or other NRTL) approved wire for input/output connecons.
Minimum size 18 AWG or 14 AWG for connuous runs.
• Make sure LEDs and drivers are cool to touch when performing maintenance.
Make sure the supply voltage is the same as the rated voltage of the luminaire.
• Do not install in a hazardous atmosphere, except where the ambient
temperature does not exceed the rated operang temperature of the xture.
• Keep ghtly closed when in operaon
Electrical Requirements
The LED driver must be supplied with 120 to
277V, 50/60 Hz and connected to an individual,
properly grounded branch circuit protected by a
20 Ampere circuit breaker. Use min. 90°C supply.
Grounding Instrucons
The grounding and bonding of the overall
system shall be done in accordance with NEC
Arcle 600 and local codes
Black
Line
White
Neutral
Green
Ground
FIXTURE
Figure 1
Direct mount to Juncon Box:
1) Remove the boom quick mounng plate from the xture to
install onto juncon box.
2) Apply xture to mounng surface by fastening mounng plate
to recessed juncon box. Use integral bubble level to ensure
that the plate is level.
3) Connect leads from back of xture to the power supply leads:
Green to green (ground), black to black (hot), white to white
(neutral).
4) Take care to not pinch any wires when connecng the xture to
the mounng plate.
5) Tighten Allen set screws on front of xture to secure to the
mounng plate.
6) For wet locaons, caulk between the rear housing and
mounng surface for a water ght seal.
Using Oponal 16256AZT Wall Mount
Extension Juncon Box:
NOTE: Quick mounng plate not required.
1) Apply extension juncon box to mounng surface (two opons).
a. Recessed juncon box: Fasten extension juncon box
to recessed juncon box.
b. Conduit feed: Fasten extension juncon box to desired
surface and remove appropriate threaded conduit plug
and route conduit and circuit wiring into the extension
juncon box using appropriate methods.
2) Connect leads from back of xture to the power supply leads:
Green to green (ground), black to black (hot), white to white
(neutral).
3) Arrange connected wires into extension juncon box.
4) Aach xture to extension juncon box. Take care to not pinch
any wires when connecng the xture.
5) Tighten Allen set screws on front of xture to secure to the
extension juncon box.
6) For wet locaons, caulk between the rear housing and mounng
surface for a water ght seal.
Using Oponal 16292AZT
Trunnion Mount:
NOTE: Quick mounng plate not required.
1) Connect leads from back of xture to
the power supply leads: Green to green
(ground), black to black (hot), white to
white(neutral).
2) Arrange connected wires into trunnion
juncon box.
3) Aach xture to trunnion extension
juncon box. Take care to not pinch any
wires when connecng the xture.
4) Mount the trunnion with appropriate
fasteners to selected surface. Mounng
slots are ½”.
5) Loosen pivot screws to adjust angle of
xture to desired posion. Reghten pivot
screws.
This device complies with part 15 of the FCC Rules. Operaon is subject to the following two condions:
1) This device may not cause harmful interference, and
2) This device must accept any interference received, including interference that may cause
undesired operaon.
Note: This equipment has been tested and found to comply with the limits for a Class A digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protecon against
harmful interference in a residenal installaon. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the instrucons, may cause harmful
interference to radio communicaons.
However, there is no guarantee that interference will not occur in a parcular installaon. If this
equipment does cause harmful interference to radio or television recepon, which can be determined
by turning the equipment o and on, the user is encouraged to try to correct the interference by one or
more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separaon between the equipment and receiver.
• Connect the equipment into an outlet on a circuit dierent from that to which the receiver is
connected.
• Consult the dealer or an experienced radio/TV technician for help.
Page is loading ...
IS-16236-CB
For warranty informaon please visit: hp://www.kichler.com/warranty
We’re here to help 866-558-5706
Hrs: M-F 9am to 5pm EST
Kichler 16236, 16237, 16238 Installaon Guide
LED Slim Wallpack
IMPORTANT: Read before removing xture from carton. Retain for
future reference.
SAFETY: This xture must be wired in accordance with the
NATIONAL ELECTRICAL CODE (NEC) and applicable local codes and
ordinances. A person familiar with the construcon and operaon
of the product and the hazards involved must install this product.
A qualied licensed electrician should complete all work. Proper
grounding is required for safety.
WARNING: Make certain power is OFF before installing or
maintaining xture.
RISK OF INJURY: Fixture may become damaged and/or unstable if
not installed properly.
Cauons:
Installaon Instrucons:Fixture Diagram
NOTE: Turn o electrical supply at the breaker. Follow all local
electrical codes for wiring and grounding requirements.
Tools Required: 1/8” Allen Key, Phillips Screw Driver, Wire
Strippers & Cuers
NOTE: Unpack xture and ensure that there are no damaged parts.
FCC Informaon:
RISK OF FIRE, EXPLOSION AND ELECTRIC SHOCK
• This product should be installed, inspected, and maintained by a qualied
electrician only, in accordance with the NEC (Naonal Electric Code) and all
local codes.
• Turn o electrical power before inspecon, installaon or removal.
• Use only UL (or other NRTL) approved wire for input/output connecons.
Minimum size 18 AWG or 14 AWG for connuous runs.
• Make sure LEDs and drivers are cool to touch when performing maintenance.
Make sure the supply voltage is the same as the rated voltage of the luminaire.
• Do not install in a hazardous atmosphere, except where the ambient
temperature does not exceed the rated operang temperature of the xture.
• Keep ghtly closed when in operaon
Electrical Requirements
The LED driver must be supplied with 120 to
277V, 50/60 Hz and connected to an individual,
properly grounded branch circuit protected by a
20 Ampere circuit breaker. Use min. 90°C supply.
Grounding Instrucons
The grounding and bonding of the overall
system shall be done in accordance with NEC
Arcle 600 and local codes
Black
Line
White
Neutral
Green
Ground
FIXTURE
Figure 1
Direct mount to Juncon Box:
1) Remove the boom quick mounng plate from the xture to
install onto juncon box.
2) Apply xture to mounng surface by fastening mounng plate
to recessed juncon box. Use integral bubble level to ensure
that the plate is level.
3) Connect leads from back of xture to the power supply leads:
Green to green (ground), black to black (hot), white to white
(neutral).
4) Take care to not pinch any wires when connecng the xture to
the mounng plate.
5) Tighten Allen set screws on front of xture to secure to the
mounng plate.
6) For wet locaons, caulk between the rear housing and
mounng surface for a water ght seal.
Using Oponal 16256AZT Wall Mount
Extension Juncon Box:
NOTE: Quick mounng plate not required.
1) Apply extension juncon box to mounng surface (two opons).
a. Recessed juncon box: Fasten extension juncon box
to recessed juncon box.
b. Conduit feed: Fasten extension juncon box to desired
surface and remove appropriate threaded conduit plug
and route conduit and circuit wiring into the extension
juncon box using appropriate methods.
2) Connect leads from back of xture to the power supply leads:
Green to green (ground), black to black (hot), white to white
(neutral).
3) Arrange connected wires into extension juncon box.
4) Aach xture to extension juncon box. Take care to not pinch
any wires when connecng the xture.
5) Tighten Allen set screws on front of xture to secure to the
extension juncon box.
6) For wet locaons, caulk between the rear housing and mounng
surface for a water ght seal.
Using Oponal 16292AZT
Trunnion Mount:
NOTE: Quick mounng plate not required.
1) Connect leads from back of xture to
the power supply leads: Green to green
(ground), black to black (hot), white to
white(neutral).
2) Arrange connected wires into trunnion
juncon box.
3) Aach xture to trunnion extension
juncon box. Take care to not pinch any
wires when connecng the xture.
4) Mount the trunnion with appropriate
fasteners to selected surface. Mounng
slots are ½”.
5) Loosen pivot screws to adjust angle of
xture to desired posion. Reghten pivot
screws.
This device complies with part 15 of the FCC Rules. Operaon is subject to the following two condions:
1) This device may not cause harmful interference, and
2) This device must accept any interference received, including interference that may cause
undesired operaon.
Note: This equipment has been tested and found to comply with the limits for a Class A digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protecon against
harmful interference in a residenal installaon. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the instrucons, may cause harmful
interference to radio communicaons.
However, there is no guarantee that interference will not occur in a parcular installaon. If this
equipment does cause harmful interference to radio or television recepon, which can be determined
by turning the equipment o and on, the user is encouraged to try to correct the interference by one or
more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separaon between the equipment and receiver.
• Connect the equipment into an outlet on a circuit dierent from that to which the receiver is
connected.
• Consult the dealer or an experienced radio/TV technician for help.
Page is loading ...
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4

Kichler Lighting 16236AZT50 User manual

Brand
Kichler Lighting
Model
16236AZT50
Type
User manual
This manual is also suitable for
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

in other languages

Related papers

Other documents