2. Kichler Lighting
  3. 16236AZT30

Kichler Lighting 16236AZT30, 16236AZT40, 16236AZT50 User manual

  • Hello! I am an AI chatbot trained to assist you with the Kichler Lighting 16236AZT30 User manual. I’ve already reviewed the document and can help you find the information you need or explain it in simple terms. Just ask your questions, and providing more details will help me assist you more effectively!
For warranty informaon please visit: hp://www.kichler.com/warranty
IS-16236-US
We’re here to help 866-558-5706
Hrs: M-F 9am to 5pm EST
Kichler 16236, 16237, 16238 Installaon Guide
LED Slim Wallpack
IMPORTANT: Read before removing xture from carton. Retain for
future reference.
SAFETY: This xture must be wired in accordance with the
NATIONAL ELECTRICAL CODE (NEC) and applicable local codes and
ordinances. A person familiar with the construcon and operaon
of the product and the hazards involved must install this product.
A qualied licensed electrician should complete all work. Proper
grounding is required for safety.
WARNING: Make certain power is OFF before installing or
maintaining xture.
RISK OF INJURY: Fixture may become damaged and/or unstable if
not installed properly.
Cauons:
Installaon Instrucons:Fixture Diagram
NOTE: Turn o electrical supply at the breaker. Follow all local
electrical codes for wiring and grounding requirements.
Tools Required: 1/8” Allen Key, Phillips Screw Driver, Wire
Strippers & Cuers
NOTE: Unpack xture and ensure that there are no damaged parts.
FCC Informaon:
RISK OF FIRE, EXPLOSION AND ELECTRIC SHOCK
• This product should be installed, inspected, and maintained by a qualied
electrician only, in accordance with the NEC (Naonal Electric Code) and all
local codes.
• Turn o electrical power before inspecon, installaon or removal.
• Use only UL (or other NRTL) approved wire for input/output connecons.
Minimum size 18 AWG or 14 AWG for connuous runs.
• Make sure LEDs and drivers are cool to touch when performing maintenance.
Make sure the supply voltage is the same as the rated voltage of the luminaire.
• Do not install in a hazardous atmosphere, except where the ambient
temperature does not exceed the rated operang temperature of the xture.
• Keep ghtly closed when in operaon
Electrical Requirements
The LED driver must be supplied with 120 to
277V, 50/60 Hz and connected to an individual,
properly grounded branch circuit protected by a
20 Ampere circuit breaker. Use min. 90°C supply.
Grounding Instrucons
The grounding and bonding of the overall
system shall be done in accordance with NEC
Arcle 600 and local codes
Black
Line
White
Neutral
Green
Ground
FIXTURE
Figure 1
Direct mount to Juncon Box:
1) Remove the boom quick mounng plate from the xture to
install onto juncon box.
2) Apply xture to mounng surface by fastening mounng plate
to recessed juncon box. Use integral bubble level to ensure
that the plate is level.
3) Connect leads from back of xture to the power supply leads:
Green to green (ground), black to black (hot), white to white
(neutral).
4) Take care to not pinch any wires when connecng the xture to
the mounng plate.
5) Tighten Allen set screws on front of xture to secure to the
mounng plate.
6) For wet locaons, caulk between the rear housing and
mounng surface for a water ght seal.
Using Oponal 16256AZT Wall Mount
Extension Juncon Box:
NOTE: Quick mounng plate not required.
1) Apply extension juncon box to mounng surface (two opons).
a. Recessed juncon box: Fasten extension juncon box
to recessed juncon box.
b. Conduit feed: Fasten extension juncon box to desired
surface and remove appropriate threaded conduit plug
and route conduit and circuit wiring into the extension
juncon box using appropriate methods.
2) Connect leads from back of xture to the power supply leads:
Green to green (ground), black to black (hot), white to white
(neutral).
3) Arrange connected wires into extension juncon box.
4) Aach xture to extension juncon box. Take care to not pinch
any wires when connecng the xture.
5) Tighten Allen set screws on front of xture to secure to the
extension juncon box.
6) For wet locaons, caulk between the rear housing and mounng
surface for a water ght seal.
Using Oponal 16292AZT
Trunnion Mount:
NOTE: Quick mounng plate not required.
1) Connect leads from back of xture to
the power supply leads: Green to green
(ground), black to black (hot), white to
white(neutral).
2) Arrange connected wires into trunnion
juncon box.
3) Aach xture to trunnion extension
juncon box. Take care to not pinch any
wires when connecng the xture.
4) Mount the trunnion with appropriate
fasteners to selected surface. Mounng
slots are ½”.
5) Loosen pivot screws to adjust angle of
xture to desired posion. Reghten pivot
screws.
This device complies with part 15 of the FCC Rules. Operaon is subject to the following two condions:
1) This device may not cause harmful interference, and
2) This device must accept any interference received, including interference that may cause
undesired operaon.
Note: This equipment has been tested and found to comply with the limits for a Class A digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protecon against
harmful interference in a residenal installaon. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the instrucons, may cause harmful
interference to radio communicaons.
However, there is no guarantee that interference will not occur in a parcular installaon. If this
equipment does cause harmful interference to radio or television recepon, which can be determined
by turning the equipment o and on, the user is encouraged to try to correct the interference by one or
more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separaon between the equipment and receiver.
• Connect the equipment into an outlet on a circuit dierent from that to which the receiver is
connected.
• Consult the dealer or an experienced radio/TV technician for help.
Page is loading ...
IS-16236-CB
For warranty informaon please visit: hp://www.kichler.com/warranty
We’re here to help 866-558-5706
Hrs: M-F 9am to 5pm EST
Kichler 16236, 16237, 16238 Installaon Guide
LED Slim Wallpack
IMPORTANT: Read before removing xture from carton. Retain for
future reference.
SAFETY: This xture must be wired in accordance with the
NATIONAL ELECTRICAL CODE (NEC) and applicable local codes and
ordinances. A person familiar with the construcon and operaon
of the product and the hazards involved must install this product.
A qualied licensed electrician should complete all work. Proper
grounding is required for safety.
WARNING: Make certain power is OFF before installing or
maintaining xture.
RISK OF INJURY: Fixture may become damaged and/or unstable if
not installed properly.
Cauons:
Installaon Instrucons:Fixture Diagram
NOTE: Turn o electrical supply at the breaker. Follow all local
electrical codes for wiring and grounding requirements.
Tools Required: 1/8” Allen Key, Phillips Screw Driver, Wire
Strippers & Cuers
NOTE: Unpack xture and ensure that there are no damaged parts.
FCC Informaon:
RISK OF FIRE, EXPLOSION AND ELECTRIC SHOCK
• This product should be installed, inspected, and maintained by a qualied
electrician only, in accordance with the NEC (Naonal Electric Code) and all
local codes.
• Turn o electrical power before inspecon, installaon or removal.
• Use only UL (or other NRTL) approved wire for input/output connecons.
Minimum size 18 AWG or 14 AWG for connuous runs.
• Make sure LEDs and drivers are cool to touch when performing maintenance.
Make sure the supply voltage is the same as the rated voltage of the luminaire.
• Do not install in a hazardous atmosphere, except where the ambient
temperature does not exceed the rated operang temperature of the xture.
• Keep ghtly closed when in operaon
Electrical Requirements
The LED driver must be supplied with 120 to
277V, 50/60 Hz and connected to an individual,
properly grounded branch circuit protected by a
20 Ampere circuit breaker. Use min. 90°C supply.
Grounding Instrucons
The grounding and bonding of the overall
system shall be done in accordance with NEC
Arcle 600 and local codes
Black
Line
White
Neutral
Green
Ground
FIXTURE
Figure 1
Direct mount to Juncon Box:
1) Remove the boom quick mounng plate from the xture to
install onto juncon box.
2) Apply xture to mounng surface by fastening mounng plate
to recessed juncon box. Use integral bubble level to ensure
that the plate is level.
3) Connect leads from back of xture to the power supply leads:
Green to green (ground), black to black (hot), white to white
(neutral).
4) Take care to not pinch any wires when connecng the xture to
the mounng plate.
5) Tighten Allen set screws on front of xture to secure to the
mounng plate.
6) For wet locaons, caulk between the rear housing and
mounng surface for a water ght seal.
Using Oponal 16256AZT Wall Mount
Extension Juncon Box:
NOTE: Quick mounng plate not required.
1) Apply extension juncon box to mounng surface (two opons).
a. Recessed juncon box: Fasten extension juncon box
to recessed juncon box.
b. Conduit feed: Fasten extension juncon box to desired
surface and remove appropriate threaded conduit plug
and route conduit and circuit wiring into the extension
juncon box using appropriate methods.
2) Connect leads from back of xture to the power supply leads:
Green to green (ground), black to black (hot), white to white
(neutral).
3) Arrange connected wires into extension juncon box.
4) Aach xture to extension juncon box. Take care to not pinch
any wires when connecng the xture.
5) Tighten Allen set screws on front of xture to secure to the
extension juncon box.
6) For wet locaons, caulk between the rear housing and mounng
surface for a water ght seal.
Using Oponal 16292AZT
Trunnion Mount:
NOTE: Quick mounng plate not required.
1) Connect leads from back of xture to
the power supply leads: Green to green
(ground), black to black (hot), white to
white(neutral).
2) Arrange connected wires into trunnion
juncon box.
3) Aach xture to trunnion extension
juncon box. Take care to not pinch any
wires when connecng the xture.
4) Mount the trunnion with appropriate
fasteners to selected surface. Mounng
slots are ½”.
5) Loosen pivot screws to adjust angle of
xture to desired posion. Reghten pivot
screws.
This device complies with part 15 of the FCC Rules. Operaon is subject to the following two condions:
1) This device may not cause harmful interference, and
2) This device must accept any interference received, including interference that may cause
undesired operaon.
Note: This equipment has been tested and found to comply with the limits for a Class A digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protecon against
harmful interference in a residenal installaon. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the instrucons, may cause harmful
interference to radio communicaons.
However, there is no guarantee that interference will not occur in a parcular installaon. If this
equipment does cause harmful interference to radio or television recepon, which can be determined
by turning the equipment o and on, the user is encouraged to try to correct the interference by one or
more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separaon between the equipment and receiver.
• Connect the equipment into an outlet on a circuit dierent from that to which the receiver is
connected.
• Consult the dealer or an experienced radio/TV technician for help.
Page is loading ...
/