2. Office
  3. Smart card readers
  4. Durabook
  5. R11
R11

Durabook R11 User manual

  • Hello! I have reviewed the provided user manual for the Smart Card Module. This document provides detailed step by step instructions on how to install the expansion module to your R11 Rugged Tablet, including information about screws, gaskets and other parts. I'm ready to answer any questions you may have about this device or the installation process.
  • What should I do if any item is damaged?
    What should be removed before installing any expansion modules?
    What is torque for the screws?
©2021 Twinhead International Corp and/or its affiliates. All rights reserved.
1
R11 Rugged Tablet
Expansion Modules
Smart Card
P/N: 62+030990+20
Expansion Modules Smart Card
2
Package Contents
If any of following items is damaged, please contact your retailer.
Smart Card Module Cover
Gasket
Module Bracket
Module FPC
Smart Card Board
Smart Card Reader
Sponges
Screw & O RING
(4+2+3+2)
Expansion Modules Smart Card
3
Smart Card Module Screws
Screw Type
Quantity
Torque
2 (cover to lower
case)
2.0 ± 0.3 Kgf-cm
4 (cover to lower
case)
2.0 ± 0.3 Kgf-cm
3 (module to its
bracket)
2.0 ± 0.3 Kgf-cm
2 (bracket to lower
case)
2.0 ± 0.3 Kgf-cm
NOTE
The pictures are for reference only, actual items may slightly differ.
Installation
This section will guide you on how to install the expansion modules to your tablet
PC.
Note: Make sure to remove the battery before installing any type of expansion
modules. For more information on how to remove/install the battery, please refer
to the tablet PC service guide.
Installing the Smart Card Module
To install the smart card module, follow the steps below:
1. Remove the screw securing the mylar on the DDR door.
Expansion Modules Smart Card
4
2. Remove the mylars from the DDR door.
3. Attach the expansion sponge and four sponges to the DDR door.
4. Connect the smart card module FFC to the mainboard connector. Then secure
the latch.
Expansion Modules Smart Card
5
5. Route the smart card module FFC through the opening on the bracket. Then
by aligning with the screw holes, install the smart card module bracket onto
its slot on the lower case.
6. Attach the 2 screws to secure the smart card module bracket to the lower
case.
7. Connect the smart card module FFC to the smart card board connector. Then
secure the latch.
Expansion Modules Smart Card
6
8. Attach the tape to secure the smart card module FFC in place.
9. Attach the tape to secure the smart card module FFC position on the bracket.
10. By aligning with the guide pins, install the smart card board onto the smart
card module bracket.
Expansion Modules Smart Card
7
11. By aligning with the screw holes, place the smart card reader on the top of
the installed smart card board.
12. Attach the 3 screws to secure the smart card module assembly onto its
bracket.
13. By aligning with the screw holes, place the gasket onto the smart card
module bracket.
Expansion Modules Smart Card
8
14. By aligning with the screw holes, place the smart card module cover on the
top of the installed gasket.
15. Attach the 6 screws to secure the smart card module cover to the lower case.
➢ M2.6X6L & O RING (marked with blue-white circle): 4 screws
➢ ISOT-M2.6X4L (marked with orange-white circle): 2 screws
16. Install the battery.
Expansion Modules Smart Card
9
Smart Card Module Screws
Screw Type
Quantity
Torque
2 (cover to lower
case)
2.0 ± 0.3 Kgf-cm
4 (cover to lower
case)
2.0 ± 0.3 Kgf-cm
3 (module to its
bracket)
2.0 ± 0.3 Kgf-cm
2 (bracket to lower
case)
2.0 ± 0.3 Kgf-cm
Twinhead International Corp.
11F, No.550, Ruiguang Rd., Neihu, Taipei 11492, Taiwan, R.O.C.
/