Adtec HDMI2qam Quick start guide

Brand
Adtec
Model
HDMI2qam
Category
Video servers/encoders
Type
Quick start guide
System
Login
Duration
Network
Time
NTP
Alarm
COM2
Firmware
Front Panel Menus:
Use Mode Button to move through top layer menus.
Use arrows for navigation in submenus.
Use select to enter into edit mode and enter to save selection.
Units ship with the front panel
logged in by default. If you become
logged out and are prompted for a
password, use the following key
sequence for access.
Press <Select> when panel displays
‘User Login -- logged out’
Press <Up arrow>
Press <Select>
Press <Enter>
Press <Right arrow>
Press <Enter>
Quick Start Guide
Getting Started
Thank you for your purchase of the Adtec HDMI2QAM. This quick start
guide should help you with your initial setup. Additional support can be provided
through our Customer Support Department.
Telephone: 615.256.6619
Email: [email protected]
Internet: www.adtecinc.com/supportrequest/
The most recent firmware is available on our support website,
www.adtecinc.com.
Front Panel LEDs:
System LED Status
Power
Power is OFF
Power is ON
Alarm
No System Alarm
Minor Alarm
Major Alarm
Link
No Link Detected
Link Active
Busy
No Network Traffic
Network Traffic Present
EAS
Not Currently Used
2
Dual Channel Encoder
Services
Audio
Modulator
Mod Encoding
Mod Mode
UpCnv Channel
UpCnv Power
CH1 CH2
Short Name
Long Name
Number
Status
Input
Closed Cap
CH1 CH2
Mode
Type
1920x1080 29i 33.77M
1DD 192K 2DD 192K 48
Quick View
Video Resolution Frame Rate Video Bit Rate
Audio Input 1 & 2 Sampling Rate
The front panel will display a ‘Quick View’ of
your incoming streams on the HDMI ports.
This information can be viewed by pressing
the down arrow key when the front panel is
at it’s upmost menu ‘System Banner.’
Top
Menu
Banner
Quick View 1
Quick View 2
Channel 1 & 2
Encode
Not Active
Encoding
Transitioning
Video
No Video
(Audio Only)
Video Present
Format Not Supported
No Video Present
SD
SD Resolution Detected
HD
1080i Resolution Detected
720p Resolution Detected
EAS
Not Currently Used
QAM
A/B/C
Not Currently Used
256
Not Currently Used
128
Not Currently Used
64
Not Currently Used
Channel 2
Channel 1
Encode Video SD HD EAS
A/ B /C 256
QAM
128 64
EAS
Encode Video SD HD EAS
2
QAM
HDMI
To begin, you will need to connect to your HDMI2QAM via
ethernet directly, or by adding the unit to your local area network.
To add the device to a LAN, connect a standard CAT 5
Ethernet cable to your network router and then to the Ethernet port
on the back of the device. The default address for all Adtec devices is
192.168.10.48. If your network is DHCP enabled and you prefer that
over a static IP, you can turn on DHCP for the device via the front
panel, System > Network menu.
To connect directly to the device, make sure that your
computer and the device have IP addresses within the same IP class
range (ex. 192.168.10.48 for the device and 192.168.10.49 for your
computer). If you need to change the IP address of the device, this
can be done via the front panel, System > Network menu. Using a
CAT 5 crossover cable, connect one end to your computer and the
other to the Ethernet port found on the processor section of the back
panel. (Some computers can auto negotiate the connection and a
crossover may not be necessary.)
Adtec Digital Technical Support: 615.256.6619 www.adtecinc.com 10.15.09
Web-Based Control ApplicationGetting Connected
Processor ..........................................................................................
Power AC Power - Standard 3 pin plug (70-240 VAC 50 - 60 Hz)
GigE GigE Interface - Can be used for control and conguration.
COM2 API Serial Communication Interface
COM1 Serial Port Used for Troubleshooting
Ethernet 10/100 base T Ethernet interface
USB 2.0 Not Currently Supported
Video/Audio Input.................................................................................
CVBS Input 1 BNC 75 Ohm Input for CC signal reception
HDMI Input 1 HDMI v 1.3a, DVI v1.0, CEA-861-D / 720p & 1080i only
CVBS Input 2 BNC 75 Ohm Input for CC signal reception
HDMI Input 2 HDMI v 1.3a, DVI v1.0, CEA-861-D / 720p & 1080i only
EAS In CVBS BNC 75 Ohm for NTSC or PAL D1 Video - Not Functional
EAS In Audio L & R Unbalanced left & right audio channels RCA jack - Not Functional
Output ...................................................................................................
ASI Out BNC 50 Ohm, Asynchronous Serial Interface (EN 50083-9)
RF Main F-style RF female jack, Freq: 50 to 862 Mhz, 48 dBmV to 58 dBmV in 0.1 dB
RF Out Monitor F-style RF female jack, -20 dBmV from Main - Not Functional
IF In F-style RF female/jack, Freq: 44 MHz
IF Out F-style RF female/jack, Freq: 44 MHz
EAS Control 9-Pin Interface - Not Functional
Adtec Digital has adopted zero-conguration
networking technology, streamlining the setup and
conguration processes for our products. The use of this
technology enables automatic discovery of Adtec devices
and services on an IP network. Used in tandem with the
web-based control and conguration applications we can
now provide 1-click access to any device.
By using the built-in Bonjour
©
locater in Apple's
©
Safari
©
browser or the plug-ins readily available for IE
©
or
Firefox
©
browsers, users can locate all of the Adtec
devices on a network by referencing the serial number on
the back of the device. Clicking on the unit in the
Bonjour
©
list will re-route you to a login page. If you do
not wish to use Bonjour, you can reach the device’s web
application by pointing your browser to the IP Address of
the device. Ex. http://192.168.10.48.
The left panel of the application will report current status in real-time while the right panel tabs will allow
you to congure your device. Additional hints regarding conguration options can be found by clicking on the
hints buttons
associated with each
eld or group of elds.
?
COM2
COM1
Ethernet
USB 2.0
PROCESSOR
Video/Audio Input
GigE
CVBS Input 2
HDMI Input 2
CVBS Input 2
HDMI Input 2
EAS In CVBS
EAS In Audio L
EAS In Audio R
ASI Out
RF Main
RF Out Monitor
IF In
EAS Control
IF Out
Output
RF Main
  • Page 1 1
  • Page 2 2

Adtec HDMI2qam Quick start guide

Brand
Adtec
Model
HDMI2qam
Category
Video servers/encoders
Type
Quick start guide
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents