Hanasis HW-3000 User manual

HW-3000

※ Please read and learn the manual carefully for your safety and proper way of use.

HW-3000 preview

Do not block the ports(holes), Vents, etc, of the system and do not insert objects.

Damage to a component within the system may cause electric shock or fire.

Do not touch the system plug or power cord with wet hands. There is a danger of electric shock.

Do not exceed the standard capacity(Voltage/current) of a multiplug or power outlet extension when using it for the product.

There is a danger of electric shock or fire hazard.

Do not unplug the power cord by pulling the cable only. If the cord is damaged, it may cause electric shock.

Connect the power cord to the AC adaptor firmly. Use only the AC adaptor supplied with the product.

Otherwise, there is a danger of fire due to an incomplete contact.

Do not use the system in a humid location such as a bathroom or sauna.

Please use the system within the recommended temperature and humidity range(10~32˚C, 20~80% RH).

Avoid direct sunlight when the system is in an air-tight location such as inside a vehicle.

There is a danger of a fire hazard. The system may overheat and also present opportunity to thieves.

Safety precautions

HW-3000 preview

Specification & options

Locations

For your security and to prevent damage, please read the following safety instructions carefully.

Failing to follow instructions marked with this symbol may cause personal injury and even fatality.

Safety precautions

HW-3000 preview

Specification & options

Locations

Thank you for purchasing Hanasis's POS.

(Product specifications may differ according to region and may be changed without prior notice)

■ System preview

3000

Class-A digital device

A digital device that is marketed for use in a commercial, industrial or business environment,

exclusive of a device which is marketed for use by the general public or is intended to be used in the home.

This product is developed and tested on the basis of our reliability and outstanding technology.

This product has applied exclusive and emotional design and also provides wide expandability such as barcode scanner or NFC.

This product has applied low power atom platform design, 15” Window(TFT) touch screen and 9.7” dual monitor expandability.

This will allow users to save maintainance cost and will provide comfortable user experience.

This product is designed for users to fix easily by using hand screws in system main body and stand, and also by decreasing the number of screws.

This product has acquired domestic and international standard, applied a technology patent that is created by Hanasis.

registered trademark

The symbol mark is the foundation element that symbolizes the Hanasis corporation and it is also a symbol of communication at both home and abroad.

The basic concept is a leading IT industry. It embodies Hanasis's corporate goal to link world faster by using advanced IT technology.

The symbol mark express Hanasis's industry representative. The symbol expresses the image of network envrionment and advanced technology in dynamic way.

Safety precautions

HW-3000 preview

Specification & options

Locations

(Product specifications may differ according to region and may be changed without prior notice.)

◆ Specification ◆ Options

OS

Wall Mount

Touch Panel

Dual Display

iButton

MSR

Barcode Scanner

Color Product

Smart IC Card

Microsoft

®

Windows7, POSReady7 / 2009, windows XP

Fixed Type , Swivel Type

(75x75, 100x100mm VESA)

15", 5-Wire Resistive (Bezel type / Bezelless type)

9.7”, TFT-LCD, 1024x768, LED panel (Touch)

15”, TFT-LCD, 1024x768, LED panel

Probe(USB), Dallas key

ISO Track2 , Track 1&2 , Track 1&2&3

USB Module(Internal) type, 1D, 2D

IC Card Reader(USB), EMV Level#1

White Black

Processor(CPU)

Chipset

Memory

HDD

Display

VGA / DVI

HDMI

LAN

Serial(RS-232C)

Parallel(LPT)

PS/2

USB

Audio

Speaker

Expansion Interface

Cooler & FAN

Power Adaptor

Dimension(mm)

Weight

Intel

®

Intel

®

Celeron® 1037U Dual-Core (1.8GHz, 2M Cash)

NM70

2GB DDR3 1333MHz, SoDIMM (Up to 8GB)

2.5”, SATA-III 320GB~ or SSD 32GB~

m-SATA (32GB~)

15", 1024 X 768, 24Bit

Luminance : 250 cd/㎡, Backlight : LED

1EA VGA (DSUB15) Intel® HD Graphics 2500

-

2 EA (Intel® Gigabit LAN)

4 EA (DSUB-9p x 3EA / RJ-45 x 1EA)

-

2 EA (Keyboard / Mouse)

4 EA (I/O) (USB2.0)

2 EA (Front) (USB2.0)

2 EA (Line-Out / MIC-In) Realtek ALC269 HD2.1 Audio

1 EA (1W)

1 EA PCIe Socket

1 EA Full Size Mini PCIe Socket (m-SATA)

Fanless

60[W] Adaptor

Input AC 100~240V/50~60HZ, DC 12V/5A

364(W) x 332(H) x 200(D) (Normal Angle, With Stand)

7.3kg

NFC

Serial Module(Interal) type, SSCPRO NFM1V0

Safety precautions

HW-3000 preview

Specification & options

Locations

ㆍParts description

ㆍI/O port

ㆍRating label zone

(Product specifications may differ according to region and may be changed without prior notice.)

Power supply lamp

Error lamp

Reset button

Card reader(MSR)

Exteral USB(2port)

HDD lamp

LAN lamp

Dual(touch) monitor

Cover cable

NFC reader(Option)

Barcode scanner(Option)

Camera(Option)

Cable vent

Cable space

(9.7” / 15”)

Power button & Power supply lamp

1. Card reader (MSR) : Device that recognizes credit cards.

※ power supply lamp : green light / error lamp : red light / reset button : Use when initializing the Card reader.

2. HDD lamp : The light will be turned on when the hard disk is reading or writting data.

3. LAN lamp : The light will be turned on when connected to the internet.

4. Power supply lamp : The light will be turned on when the system is on.

5. 9.7” / 15” Dual(touch) monitor : Option

6. Barcode scanner / NFC reader : Option

7. Cover cable : Disassemble the cover and then you can connect the I/O port.

8. Cable space / vent : Disassemble the cover and then you can reorganize the cables that are connected.

Safety precautions

HW-3000 preview

Specification & options

Locations

ㆍParts description

ㆍI/O port

ㆍRating label zone

1. PS/2 (MOUSE)

2. PS/2 (KBD)

3. D-SUB 9PIN serial(COM)

4. D-SUB 15PIN VGA

5. RJ-45 LAN

6. USB 2.0

7. AUDIO port (LINE-OUT)

8. MIC port (MIC-IN)

9. DIN 4PIN 12V DC-IN

10. 12V DC-OUT

11. RJ-45 8PIN COM

12. RJ-45 8PIN MSR86%W\SH

13. HDD

PS/2 type of mouse

PS/2 type of keyboard

Equiments that use serial port such a barcode scanner and printer

Dual(touch) monitor

Internet connection

USB keyboard, USB mouse, NFC reader etc.

External speakers

External mic

Adaptor jack that provides system power

Dual(touch) monitor power jack

Equiments that use serial port

0DJQHWLF6WULSH5HDGHU

SSD or 2.5” HDD

(standard)

OUT(12V)

COM4 MSR(USB)

IN(12V)

POWER

HDD Tray

LAN

COM1

COM2 COM3

USB

VGA

LINE-OUT

MIC-IN

MOUSE

KBD USB

LAN

Safety precautions

HW-3000 preview

Specification & options

Locations

ㆍParts description

ㆍI/O port

ㆍRating label zone

Before you setup the product(HW-3000).

Remove the protective tape before setup.

Connecting DC Power

Supply Cable & System on

Remove the protective tape

Adjusting Viewing Angle

Protective Tape

Connecting DC Power

Supply Cable & System on

Remove the protective tape

Adjusting Viewing Angle

5˚

For optimal viewing it is recommended to look at the full face of the monitor, then adjust the monitor's angle to your own preference.

You are able to adjust the monitor's angle from 5°to 50°.

50˚

Connect the power cord to the AC adaptor firmly. Use only the AC adaptor supplied with the product.

Otherwise, there is a danger of fire due to an incomplete contact. Do not touch the system plug or power cord with wet hands

Remove the protective tape

Adjusting Viewing Angle

cover cable

stand

side cover

grab

stand

side cover

OUT(12V)IN(12V)

POWER

① Separate the Cover Rear Stand, as shown in drawing.

② Separate the Cover Cable.

③ Connect the Adaptor Cable.

④ Press Power button to turn the system on.

Please always check the directions.

Connecting DC Power

Supply Cable & System on

MSR

Winclon (Backup)

Kitchen Printer

Winclon (Restore)

POS Driver & Utility

Touch Screen

Do not apply a severe impact to the touch screen or press the screen with a sharp object such as a ball-point pen.

This may damage the touch screen.

■ Touch Point Setup

When you use the touch screen for the first time or the pointer does not precisely match your touch, calibrate the touch screen

in the ‘eGalaxTouch’. The calibration process for the touch screen may differ depending on the operating system and may not be available in

some operating systems. The following descriptions assume the Windows POSReady2009 operating system.

① Click Start→All Programs→eGalaxTouch→Configure Utility

② Click the 'Tools' tab and ‘4Points Calibration’

③ When the Calibration window appears, touch the point represented by the “+”.

④ The “+” is displayed from the bottom left to the top left of the screen sequentially.

⑤ The touch screen input points are calibrated.

MSR

Winclon (Backup)

Kitchen Printer

Winclon (Restore)

POS Driver & Utility

Touch Screen

Learn the proper way of using card reader before using the product.

When the card is inappropriately recognized, the red ligth will be turned on with the beep sound.

① grab your credit card as the picture shows.

※ make sure the magnetic side of the card towards out side.

② Push your credit card in the direction of the arrow.

③ Slide down your credit card gently in the direction of the arrow.

■ Proper way of using the card reader

1

2

3

MSR

Winclon (Backup)

Kitchen Printer

Winclon (Restore)

POS Driver & Utility

Touch Screen

In order to connect POS device with kitchen printer, please regard to the following connection drawing.

You must use the interchangable gender that is provided by Hanasis.

■ cable connection specification for kitchen printer serial cable

[SRP-350] [SRP-330] [TM-T83] [SRP-350] [TM-T83]

1: N.C

2: DSR

3: TXD

4: RXD

5: RTS

6: CTS

7.GND

8: DTR

POS(COM4)

1: N.C

2: DSR

3: TXD

4: RXD

5: RTS

6: CTS

7.GND

8: DTR

interchangable gender

(RJ45-DB25)

1

8

1

interchangable gender

Extension Cable

Extension cable insert

※ The interchangable gender will only be enclosed with

the kitchen bell when you order a Kitchen printer.

Connect the printer

MSR

Winclon (Backup)

Kitchen Printer

Winclon (Restore)

POS Driver & Utility

Touch Screen

You need to connect key board before you turn the power on.

Back up your current Window user environment into restore field.

It is much easier to operate if you know where the data is being backed up.

■ HDD Backup

① Connect the keyboard and mouse to the system.

After turning on the system, follow the on-screen instructions:

press <F11> when the “F11 to WinClon ...” message appears on the screen within 2 to 4 seconds (PC POST process).

② When WinClon appears on the screen, press <F10> key on your keyboard or click the mouse to select “Backup”.

③ After entering the password, press the <OK> button to continue the backup. (Password: pos)

pos

Backup file location

(The programs may vary depending on different model.)

■ HDD Backup (The programs may vary depending on different model.)

MSR

Winclon (Backup)

Kitchen Printer

Winclon (Restore)

POS Driver & Utility

Touch Screen

If you recover the Hard disk, all the data of the system will be deleted.

Please save all the important data in the external storage before you start recovering.

You can recover quickly despite when you are not able to boot from the OS or when having any problems.

Keyboard and mouse must be connected.

① Connect the keyboard and mouse to the system.

After turning on the system, follow the on-screen instructions:

press <F11> when the “F11 to WinClon ...” message appears on the screen within 2 to 4 seconds (PC POST process).

② When WinClon appears on the screen, press <F2> key or <F3> on your keyboard or

click the mouse to select “Recover recent state” or “Recover initial state”.

③ After entering the password, press the <OK> button to continue the restore. (Password: pos)

※ Recover recent state” is restored to the most recent backup of Windows.

※ Recover initial state” is restored to the factory default state.

pos

MSR

Winclon (Backup)

Kitchen Printer

Winclon (Restore)

POS Driver & Utility

Touch Screen

All the drivers and data that are provided with your purchase are in the D drive of Hard disk.

▶It is the contents from the D:\Utility.

There are install files in each folders.

Drivers

Utility

Manual

MSR

HDD AlignTool

AdobeReader

■ MSR separation

OM4 MSR(USB)

HDD Tray

Cover cable

When reassembling the card reader, you must assemble tightly otherwise the card will not be recognized by the reader.

① Separate the cover cable by pushing it upwards.

② Disconnect MSR connector.

③ Remove 2 hand screws.

④ Separate the MSR by pushing it in the direction of the arrow.

Screw

Stand

Rear Cover

HDD

EMI

9.7” Dual monitor

15” Dual monitor

Wall mount

NFC

Barcode Scanner

MSR

The stand is heavy so please be careful with it. When reassembling, for your safety,

you must put the lever in the correct insertion point.

■ Stand separation

① Lift the lever(ⓐ).

② Pull the stand in the direction of the arrow indicated.

③ Lift up and remove the stand.

Lever

Insertion Point

Stand

Rear Cover

HDD

EMI

9.7” Dual monitor

15” Dual monitor

Wall mount

NFC

Barcode Scanner

MSR

Care must be taken when removing the HDD and bracket to avoid injury.

Save all your data before clicking on Shut down. Disconnect the Adaptor cable from the system.

① Separate the Cover Cable.

② Rotate(Counter Clockwise) the Hand screw.

③ Pull the HDD out of the system.

④ Separate the HDD from the Bracket HDD.

⑤ Replace the new HDD into the Bracket HDD and assemble in reverse order.

■ Hard Disk Drive Replacement

Cover cable

Stand

Rear Cover

HDD

EMI

9.7” Dual monitor

15” Dual monitor

Wall mount

NFC

Barcode Scanner

MSR

Page is loading ...

Hanasis HW-3000 User manual

Hanasis HW-3000 User manual

Other documents