Ver.120103E
TOTAL SECURITY
SOLUTION
Design and specifications are subject to change without notice.
Supreme Resolution
Day & Night Color Camera
www.microdigital.co.kr
USER MANUAL
www.microdigital.co.kr
#1212, Hoseodae Venture Tower,
319, Gasan-Dong, Geumcheon-Gu, Seoul, Korea
Tel :+82-2-2627-5279 / Fax :+82-2-2627-5295
P/N : 3690-0001A
2 MICRODIGITAL
• This equipment has been tested and found to comply with the limits for a Class A
digital device, pursuant to part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference when the equipment
is operated in a commercial environment. This equipment generates, uses, and
can radiate radio frequency energy and, if not installed and used in accordance
with the instruction manual, may cause harmful interference to radio communica-
tions. Operation of this equipment in a residential area is likely to cause harmful
interference in which case the user will be required to correct the interference at
his own expense.
◆ Information
USER INFORMATION
• Any changes or modifications in construction of this device which are not expressly
approved by the party responsible for compliance could void the user’s authority to
operate the equipment.
• This installation should be made by a qualified service person and should abide
to all local codes.
◆ Warning
CAUTION
RISK OF ELECTRIC SHOCK, DO NOT OPEN NO USER-SERVICEABLE PARTS INSIDE.
REFER FOR SERVICING TO QUALIFIED SERVICE PERSONNEL.
THIS SYMBOL INDICATES THAT DANGEROUS VOLTAGE CONSISTING OF A
RISK OF ELECTRIC SHOCK IS PRESENT WITHIN THIS UNIT.
THIS EXCLAMATION POINT SYMBOL IS INTENDED TO ALERT THE USER
TO THE PRESENCE OF IMPORTANT OPERATING AND MAINTENANCE
(SERVICING) INSTRUCTIONS IN THE LITERATURE ACCOMPANYING THE
APPLIANCE.
This marking on the product, accessories or literature indicates that the product
and its electronic accessories should not be disposed of with other household
waste at the end of their working life. To prevent possible harm to the environ-
ment or human health from uncontrolled waste disposal, please separate these
items from other types of waste and recycle them responsibly to promote the
sustainable reuse of material resources. Household users should contact either
the retailer where they purchased this product, or their local government office,
for details of where and how they can take these items for environmentally safe
recycling. Business users should contact their supplier and check the terms and
conditions of the purchase contract. This product and its electronic accessories
should not be mixed with other commercial wastes for disposal.
CAUTION
MICRODIGITAL 3
• This equipment has been tested and found to comply with the limits for a Class A
digital device, pursuant to part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference when the equipment
is operated in a commercial environment. This equipment generates, uses, and
can radiate radio frequency energy and, if not installed and used in accordance
with the instruction manual, may cause harmful interference to radio communica-
tions. Operation of this equipment in a residential area is likely to cause harmful
interference in which case the user will be required to correct the interference at
his own expense.
◆ Information
USER INFORMATION
• Any changes or modifications in construction of this device which are not expressly
approved by the party responsible for compliance could void the user’s authority to
operate the equipment.
• This installation should be made by a qualified service person and should abide
to all local codes.
◆ Warning
RISK OF ELECTRIC SHOCK, DO NOT OPEN NO USER-SERVICEABLE PARTS INSIDE.
REFER FOR SERVICING TO QUALIFIED SERVICE PERSONNEL.
THIS SYMBOL INDICATES THAT DANGEROUS VOLTAGE CONSISTING OF A
RISK OF ELECTRIC SHOCK IS PRESENT WITHIN THIS UNIT.
THIS EXCLAMATION POINT SYMBOL IS INTENDED TO ALERT THE USER
TO THE PRESENCE OF IMPORTANT OPERATING AND MAINTENANCE
(SERVICING) INSTRUCTIONS IN THE LITERATURE ACCOMPANYING THE
APPLIANCE.
This marking on the product, accessories or literature indicates that the product
and its electronic accessories should not be disposed of with other household
waste at the end of their working life. To prevent possible harm to the environ-
ment or human health from uncontrolled waste disposal, please separate these
items from other types of waste and recycle them responsibly to promote the
sustainable reuse of material resources. Household users should contact either
the retailer where they purchased this product, or their local government office,
for details of where and how they can take these items for environmentally safe
recycling. Business users should contact their supplier and check the terms and
conditions of the purchase contract. This product and its electronic accessories
should not be mixed with other commercial wastes for disposal.
4 MICRODIGITAL
PRECAUTIONS
• Do not install the camera
in extreme temperature
conditions.
Only use the camera under conditions where
temperatures are between -10°C and +50°C.
Be especially careful to provide ventilation
when operating under high temperatures.
• Do not install or use the cam-
era in an environment where
the humidity is high.
It can cause the image quality to be poor.
• Do not install the camera
under unstable lighting
conditions.
Severe lighting change or flicker can cause
the camera to work improperly.
• Do not touch the front lens of
the camera.
This is one of the most important parts of the
camera. Be careful not to leave fingerprints
on the lens cover.
• Do not drop the camera
and protect it from physical
shocks.
It can cause malfunctions to occur.
• Never keep the camera
pointed directly at strong
light.
It can damage the CCD.
• Do not expose the camera to
rain or spill beverage on it.
If it gets wet, wipe it dry immediately. Liquids
can contain minerals that corrode the
electronic components.
• Do not expose the camera to
radioactivity. If exposed to radioactivity the CCD will fail.
Ignoring this information may result
in material loss and/or serious
personal injuries including death.
Indicates “Never Allowed.”
Ignoring this information may
result in material loss and/or a
slight injuries.
Indicates “No Disas-
sembling.”
USER INFORMATION
NOTE
• Exposure to a spotlight or an object emitting strong light may cause smear or blooming.
•
Ensure that the power source complies with normal specifications before supplying it to
the camera.
• Power supply.(Adaptor : DC12V)
- To avoid fire or shock hazard, must use a UL listed power supply.
• Monitor Impedance.
- Set the impedance switch to 75ohm standard position.
- When monitor is set to high impedance mode, the picture becomes blurred. In this
case, just check the position of the monitor impedance switch.
MICRODIGITAL 5
• Do not install the camera
in extreme temperature
conditions.
Only use the camera under conditions where
temperatures are between -10°C and +50°C.
Be especially careful to provide ventilation
when operating under high temperatures.
• Do not install or use the cam-
era in an environment where
the humidity is high.
It can cause the image quality to be poor.
• Do not install the camera
under unstable lighting
conditions.
Severe lighting change or flicker can cause
the camera to work improperly.
• Do not touch the front lens of
the camera.
This is one of the most important parts of the
camera. Be careful not to leave fingerprints
on the lens cover.
• Do not drop the camera
and protect it from physical
shocks.
It can cause malfunctions to occur.
• Never keep the camera
pointed directly at strong
light.
It can damage the CCD.
• Do not expose the camera to
rain or spill beverage on it.
If it gets wet, wipe it dry immediately. Liquids
can contain minerals that corrode the
electronic components.
• Do not expose the camera to
radioactivity. If exposed to radioactivity the CCD will fail.
Ignoring this information may result
in material loss and/or serious
personal injuries including death.
Indicates “Never Allowed.”
Ignoring this information may
result in material loss and/or a
slight injuries.
Indicates “No Disas-
sembling.”
USER INFORMATION
NOTE
• Exposure to a spotlight or an object emitting strong light may cause smear or blooming.
•
Ensure that the power source complies with normal specifications before supplying it to
the camera.
• Power supply.(Adaptor : DC12V)
- To avoid fire or shock hazard, must use a UL listed power supply.
• Monitor Impedance.
- Set the impedance switch to 75ohm standard position.
- When monitor is set to high impedance mode, the picture becomes blurred. In this
case, just check the position of the monitor impedance switch.
6 MICRODIGITAL
CONTENTS
• DESCRIPTION 8 - 10
• SPECIFICATION 11 - 12
• FEATURES 13 - 14
• COMPONENTS 15 - 29
▪ BOX CAMERA
▪ BULLET CAMERA
▪ DOME CAMERA
▪ VANDAL CAMERA
15 - 17
18 - 24
25 - 27
28 - 29
• INSTALLATION 30 - 35
▪ BOX CAMERA
▪ BULLET CAMERA
▪ DOME CAMERA
▪ VANDAL CAMERA
30 - 31
32
33
34 - 35
• OSD OPERATION 36 - 42
▪ BOX CAMERA
▪ BULLET CAMERA
▪ DOME CAMERA
▪ VANDAL CAMERA
36 - 37
37 - 39
40
41
• INSTRUCTIONS 43
• OSD STRUCTURE 44
MICRODIGITAL 7
CONTENTS
• LENS 45
• EXPOSURE 45 - 47
▪ SHUTTER
▪ BRIGHTNESS
▪ AGC
▪ DWDR
▪ RETURN
46
46
46
46
47
• WHITE BALANCE 47 - 48
• BACKLIGHT 49 - 50
• DAY & NIGHT 51 - 52
• DPC 53
• SPECIAL 54 - 59
▪ CAM TITLE
▪ MOTION
▪ PRIVACY
▪ PARK LINE
▪ IMAGE ADJ.
▪ COMM ADJ.
▪ LANGUAGE
▪ VERSION
▪ RETURN
54
55
56
57
57
58
59
59
59
• RESET & EXIT 59
• OSD STRUCTURE-MAIN MENU
8 MICRODIGITAL
DESCRIPTION
Before operating the camera, confirm the camera model and proper input
power voltage. In order to help you understand this manual thoroughly,
we’ll introduce our model description.
◆ MODEL DESCRIPTION
MDC - H8220 - VTD - 30 HU
H 8 2 2 0
Built in Heater / UTC
Number of IR-LED
Day / Night
Filter mechanism
Power source
Number of Pixels
B/W(1) / Color(2)
Case type
Model type
• EX)
CASE TYPE MODEL
TYPE
COLOR PIXEL POWER D/N
LENS
IR/HEATER
/ CASE
1: MINI BULLET
2: MODULE
3: MINI SQUARE
4: BOX
5: ZOOM
6: IR BULLET
7: IN DOOR
DOME
8: OUT DOOR
DOME
(VANDAL)
9: MINI VANDAL
i : IP
H : HD
1: B/W
2: COLOR
1: 270K
2: 410K
6: 1.3M
9: 2.1M
0: DC 12V
1: DUAL
VOLTAGE
(DC 12V/
AC24V)
2: AC230V
C
CTD
CDN
F
FDN
TDN
V
VX
VTD
VDN
WDN
F(E)
V(E)
IR : No. of
IR-LED
H: With Heater
U : UTC
CONTROL
MS : SUFACE
MOUNT TYPE
MF : FLUSH
MOUNT TYPE
IR & HEATER (MDC-6xxx, 7xxx, 8xxx MODEL)
-H -U
Built-in Heater UTC Remote Control
-30 -30H
Built-in IR LED
and CDS Sensor
Built-in IR LED
and CDS Sensor With Heater
MICRODIGITAL 9
DESCRIPTION
Before operating the camera, confirm the camera model and proper input
power voltage. In order to help you understand this manual thoroughly,
we’ll introduce our model description.
Built in Heater / UTC
Number of IR-LED
Day / Night
Filter mechanism
Power source
Number of Pixels
B/W(1) / Color(2)
Case type
CASE TYPE MODEL
TYPE
COLOR PIXEL POWER D/N
LENS
IR/HEATER
/ CASE
1: MINI BULLET
2: MODULE
3: MINI SQUARE
4: BOX
5: ZOOM
6: IR BULLET
7: IN DOOR
DOME
8: OUT DOOR
DOME
(VANDAL)
9: MINI VANDAL
i : IP
H : HD
1: B/W
2: COLOR
1: 270K
2: 410K
6: 1.3M
9: 2.1M
0: DC 12V
1: DUAL
VOLTAGE
(DC 12V/
AC24V)
2: AC230V
C
CTD
CDN
F
FDN
TDN
V
VX
VTD
VDN
WDN
F(E)
V(E)
IR : No. of
IR-LED
H: With Heater
U : UTC
CONTROL
MS : SUFACE
MOUNT TYPE
MF : FLUSH
MOUNT TYPE
IR & HEATER (MDC-6xxx, 7xxx, 8xxx MODEL)
-H -U
Built-in Heater UTC Remote Control
-30 -30H
Built-in IR LED
and CDS Sensor
Built-in IR LED
and CDS Sensor With Heater
Heater
Heater
IR
LED
IR
LED
10 MICRODIGITAL
PRECAUTIONS
DAY / NIGHT FILTER & MECHANISM
C F
DIGITAL DAY / NIGHT DIGITAL DAY / NIGHT
CTD
TRUE DAY / NIGHT (ICR-IR Cut Filter Removable)
V
DIGITAL DAY / NIGHT
VTD
TRUE DAY / NIGHT (ICR-IR Cut Filter Removable)
POWER SOURCE
MDC-xxx0
- DC 12V
MDC-xxx1
- AC 24V / DC 12V, Dual-Power
MDC-xxx2
- AC 230V
DESCRIPTION
DAY / NIGHT
DAY / NIGHT DAY / NIGHT
DAY / NIGHT
LENS
Fixed
Fixed
DC Auto
Iris Lens
AC 230V
AC 24V
DC 12V
DC 12V
DAY / NIGHT
DC Auto
Iris Lens
FILTER CHANGE
FILTER CHANGE
LENS
VARIFOCALVARIFOCAL
LENS
VARIFOCALVARIFOCAL
Signal System NTSC PAL
Scanning Frequency 15,734KHz(H), 59.94Hz(V) 15,625KHz(H), 50.00Hz(V)
Image Sensor 1/3” Interline Transfer Type High Sensitivity CCD
Sync. System Internal
Total Pixels Number 811(H) X 508(V), 410K pixels 795(H) X 596(V), 470K pixels
Effective Pixels Number 768(H) x 494(V), 380K pixels 752(H) x 582(V), 440K pixels
Horizontal Resolution More than Color 600 TV Lines
Video Output Level 1.0Vp-p, 75ohm (Video 0. 714Vp-p Sync. 0.286Vp-p)
S/N Ratio More than 52dB (AGC OFF)
Dynamic Range 52dB(*128)
DAY / NIGHT COLOR / AUTO / BW / EXTERNAL
2 DNR ON / OFF
D-WDR ON / OFF
AGC OFF / LOW / MIDDLE / HIGH
BLC BLC / HLC / OFF
AWB ATW1 / ATW2 / AWC -> SET / MANUAL
Mirror ON / OFF (Horizontal Image Inversion)
Park Line ON / OFF
Privacy Function ON / OFF (8 Zone)
Motion Detection ON / OFF (4 Zone Selectable)
Sharpness 0~31 (Level Selectable)
Electronic Shutter 1/60sec ~ 1/100,000sec 1/50sec ~ 1/100,000sec
OSD Built-In OSD Controller
Operating Temperature (-)30°C ~ (+)50°C, (-)40°C ~ (+)50°C (Built-In Heater Model)
Operating Humidity 90% RH max
Power Voltage DC12V ± 10%
MICRODIGITAL 11
DAY / NIGHT FILTER & MECHANISM
C F
DIGITAL DAY / NIGHT DIGITAL DAY / NIGHT
CTD
TRUE DAY / NIGHT (ICR-IR Cut Filter Removable)
V
DIGITAL DAY / NIGHT
VTD
TRUE DAY / NIGHT (ICR-IR Cut Filter Removable)
POWER SOURCE
MDC-xxx0
- DC 12V
MDC-xxx1
- AC 24V / DC 12V, Dual-Power
MDC-xxx2
- AC 230V
Signal System NTSC PAL
Scanning Frequency 15,734KHz(H), 59.94Hz(V) 15,625KHz(H), 50.00Hz(V)
Image Sensor 1/3” Interline Transfer Type High Sensitivity CCD
Sync. System Internal
Total Pixels Number 811(H) X 508(V), 410K pixels 795(H) X 596(V), 470K pixels
Effective Pixels Number 768(H) x 494(V), 380K pixels 752(H) x 582(V), 440K pixels
Horizontal Resolution More than Color 600 TV Lines
Video Output Level 1.0Vp-p, 75ohm (Video 0. 714Vp-p Sync. 0.286Vp-p)
S/N Ratio More than 52dB (AGC OFF)
Dynamic Range 52dB(*128)
DAY / NIGHT COLOR / AUTO / BW / EXTERNAL
2 DNR ON / OFF
D-WDR ON / OFF
AGC OFF / LOW / MIDDLE / HIGH
BLC BLC / HLC / OFF
AWB ATW1 / ATW2 / AWC -> SET / MANUAL
Mirror ON / OFF (Horizontal Image Inversion)
Park Line ON / OFF
Privacy Function ON / OFF (8 Zone)
Motion Detection ON / OFF (4 Zone Selectable)
Sharpness 0~31 (Level Selectable)
Electronic Shutter 1/60sec ~ 1/100,000sec 1/50sec ~ 1/100,000sec
OSD Built-In OSD Controller
Operating Temperature (-)30°C ~ (+)50°C, (-)40°C ~ (+)50°C (Built-In Heater Model)
Operating Humidity 90% RH max
Power Voltage DC12V ± 10%
SPECIFICATION
12 MICRODIGITAL
MODEL TYPE LENS
MDC-4xxx
CC / CS MOUNT
CTD C / CS MOUNT (ICR-IR Cut Filter Removable Mechanism)
MDC-6xxx
VTD
20, 20H, 24H, 42 Filter Changeable Vari-Focal 2.8~11.0mm DC Auto Iris Lens
35H, 45, 40H, 32 Filter Changeable Vari-Focal 6.0~50.0mm DC Auto Iris Lens
36H, 48 Filter Changeable Vari-Focal 3.5~16.0mm DC Auto Iris Lens
32U, 40HU Filter Changeable Vari-Focal 6.0~50.0mm 2 Motor Drive Lens
24HU, 42U Filter Changeable Vari-Focal 2.8~12.0mm 2 Motor Drive Lens
MDC-7xxx
F Built-In Fixed 3.6mm Board Lens
V Vari-Focal 2.8~11.0mm DC Auto Iris Lens
VTD Filter Changeable Vari-Focal 2.8~11.0mm DC Auto Iris Lens
MDC-8xxx V Vari-Focal 2.8~11.0mm DC Auto Iris Lens
VTD Filter Changeable Vari-Focal 2.8~11.0mm DC Auto Iris Lens
MODEL TYPE Min. ILLUMINATION
MDC-4xxx
C0.2 (Color) / 0.05 (BW) / Lux
CTD 0.2 (Color) / 0.03 (BW) / Lux
(ICR-IR Cut Filter Removable Mechanism)
MDC-6xxx
F 0.4 (Color) / Lux at F1.2, 0 Lux at IR LEDs On
VTD 0.3 (Color) / 0.03 (BW) / Lux at F1.4, 0 Lux at IR LEDs On
(ICR-IR Cut Filter Removable Mechanism)
MDC-7xxx
F 0.4 (Color) / Lux at F1.2
V 0.2 (Color) / 0.05 (BW) / Lux at F1.4
VTD 0.3 (Color) / 0.03 (BW) / Lux at F1.4
(ICR-IR Cut Filter Removable Mechanism)
MDC-8xxx
V 0.2 (Color) / 0.05 (BW) / Lux at F1.4
VTD 0.3 (Color) / 0.03 (BW) / Lux at F1.4 0 Lux at IR LEDs On
(ICR-IR Cut Filter Removable Mechanism)
SPECIFICATION
LENS
Min. ILLUMINATION
1/3” Interline Transfer Type High Sensitivity Color CCD
600TV Lines
The combination of a 1/3” Interline Transfer Type High Sensitivity Color CCD
and DNR DSP provides an excellent resolution of 600 TV lines.
Min. Illumination
With an incredibly Minimum Illuminatio of Amazing 0.0001Lux can Capture
Good Images Even in Extremely Low Light Conditions and Related Noises
are Significantly Reduced by the Ultra Advanced DNR(Digital Noise Reduc-
tion) Technology.
D-WDR (Digital Wide Dynamic Range)
D-WDR is a powerful and ultra advanced technology that captures clear and
superior high Resolution pictures even where images appear dark because
there is a strong back light present.
High Light Compensation (HLC) Function
High Light Compensation Function is Especially Effective to Read the Number
Plate of the Vehicles in the Street or Parking Lot at Night Time. Especially
Users Can Adjust and Select the Special Required Area to Observe the Target
Object Under the Strong Spots of Light Exist.
2D Filtering Method of Newly Advanced DNR Function
2D filtering enhances Digital Noise reduction at low light levels. 2D Filtering
of the Video Signal Optimized the Signal to Noise ratio, giving vastly improved
low light visibility
DAY / NIGHT
The camera identifies whether it is day or night and automatically switches
to the appropriate mode, depending on its environment. By day, the camera
switches to color mode in order to maintain optimal color. At night, it switches
to B/W mode so as to obtain better picture definition.
DPC (Dead Pixel Compensation [Max 64points])
When the camera becomes hot after operating a couple of days, white
spots are shown on the screen especially at low light condition and they are
recorded together with normal image. By using thise function, white spots
are removed and you can get clean images.
600 TV LINE
DAY / NIGHT
2DNR
1/3” IT
CCD
HLC
▶Specifications are subject to change without prior notice due to improvement
MICRODIGITAL 13
MODEL TYPE LENS
MDC-4xxx
CC / CS MOUNT
CTD C / CS MOUNT (ICR-IR Cut Filter Removable Mechanism)
MDC-6xxx
VTD
20, 20H, 24H, 42 Filter Changeable Vari-Focal 2.8~11.0mm DC Auto Iris Lens
35H, 45, 40H, 32 Filter Changeable Vari-Focal 6.0~50.0mm DC Auto Iris Lens
36H, 48 Filter Changeable Vari-Focal 3.5~16.0mm DC Auto Iris Lens
32U, 40HU Filter Changeable Vari-Focal 6.0~50.0mm 2 Motor Drive Lens
24HU, 42U Filter Changeable Vari-Focal 2.8~12.0mm 2 Motor Drive Lens
MDC-7xxx
F Built-In Fixed 3.6mm Board Lens
V Vari-Focal 2.8~11.0mm DC Auto Iris Lens
VTD Filter Changeable Vari-Focal 2.8~11.0mm DC Auto Iris Lens
MDC-8xxx V Vari-Focal 2.8~11.0mm DC Auto Iris Lens
VTD Filter Changeable Vari-Focal 2.8~11.0mm DC Auto Iris Lens
MODEL TYPE Min. ILLUMINATION
MDC-4xxx
C0.2 (Color) / 0.05 (BW) / Lux
CTD 0.2 (Color) / 0.03 (BW) / Lux
(ICR-IR Cut Filter Removable Mechanism)
MDC-6xxx
F 0.4 (Color) / Lux at F1.2, 0 Lux at IR LEDs On
VTD 0.3 (Color) / 0.03 (BW) / Lux at F1.4, 0 Lux at IR LEDs On
(ICR-IR Cut Filter Removable Mechanism)
MDC-7xxx
F 0.4 (Color) / Lux at F1.2
V 0.2 (Color) / 0.05 (BW) / Lux at F1.4
VTD 0.3 (Color) / 0.03 (BW) / Lux at F1.4
(ICR-IR Cut Filter Removable Mechanism)
MDC-8xxx
V 0.2 (Color) / 0.05 (BW) / Lux at F1.4
VTD 0.3 (Color) / 0.03 (BW) / Lux at F1.4 0 Lux at IR LEDs On
(ICR-IR Cut Filter Removable Mechanism)
FEATURES
1/3” Interline Transfer Type High Sensitivity Color CCD
600TV Lines
The combination of a 1/3” Interline Transfer Type High Sensitivity Color CCD
and DNR DSP provides an excellent resolution of 600 TV lines.
Min. Illumination
With an incredibly Minimum Illuminatio of Amazing 0.0001Lux can Capture
Good Images Even in Extremely Low Light Conditions and Related Noises
are Significantly Reduced by the Ultra Advanced DNR(Digital Noise Reduc-
tion) Technology.
D-WDR (Digital Wide Dynamic Range)
D-WDR is a powerful and ultra advanced technology that captures clear and
superior high Resolution pictures even where images appear dark because
there is a strong back light present.
High Light Compensation (HLC) Function
High Light Compensation Function is Especially Effective to Read the Number
Plate of the Vehicles in the Street or Parking Lot at Night Time. Especially
Users Can Adjust and Select the Special Required Area to Observe the Target
Object Under the Strong Spots of Light Exist.
2D Filtering Method of Newly Advanced DNR Function
2D filtering enhances Digital Noise reduction at low light levels. 2D Filtering
of the Video Signal Optimized the Signal to Noise ratio, giving vastly improved
low light visibility
DAY / NIGHT
The camera identifies whether it is day or night and automatically switches
to the appropriate mode, depending on its environment. By day, the camera
switches to color mode in order to maintain optimal color. At night, it switches
to B/W mode so as to obtain better picture definition.
DPC (Dead Pixel Compensation [Max 64points])
When the camera becomes hot after operating a couple of days, white
spots are shown on the screen especially at low light condition and they are
recorded together with normal image. By using thise function, white spots
are removed and you can get clean images.
600 TV LINE
DAY / NIGHT
2DNR
1/3” IT
CCD
HLC
14 MICRODIGITAL
FEATURES
PARK LINE
At this mode, possible parking line is shown on the screen. This technology
can be applied to car rear view camera.
IR SMART
It enables users to distinguish the indistinguishable images saturated by
IR LED.
Additional Functions
1. OSD - ON Screen Display menu with multi-Language support.
2. FreeArea Selectable function of BLC and MOTION DETECTION
3. Privacy Color Masking for 8 Area selection
4. Max 70% of Disk Saving Effect with Super DNR
5. Negative image Function
Weather proof IP66
MDC-6xxx , MDC-8xxx MODEL
External Focus & Focal Length Adjustment
77Ø, 88Ø Series (MDC-6220VTD-35H, 36H, 45, 48)
Dual(Surface / Flush) Mount Type Vandal Proof Dome Camera
MDC-8xxx MODEL
1. The unit is installed by two types of installation with flush or surface
mount. When the camera is installed with flush mount, the unit can be
installed into an existing two-gang junction box.
2. Surface or Flush Mounting using the supplied surface mount bracket.
C / CS Mount Lens Adjustable
MDC-4xxx MODEL
UTC Remote Controller
- Long distance controller.
- Menu can be adjusted without opening the camera case.
- It is of conveniently portable size.
IP66
SMART
IR
Vandal Proof
PARK LINE
OSD
1. Camera
2. Auto IRIS Lens Connection Plug
3. L-WRENCH
4. C - Mount Adaptor
5. Manual
Width Height depth
64 58 102
MICRODIGITAL 15
PARK LINE
At this mode, possible parking line is shown on the screen. This technology
can be applied to car rear view camera.
IR SMART
It enables users to distinguish the indistinguishable images saturated by
IR LED.
Additional Functions
1. OSD - ON Screen Display menu with multi-Language support.
2. FreeArea Selectable function of BLC and MOTION DETECTION
3. Privacy Color Masking for 8 Area selection
4. Max 70% of Disk Saving Effect with Super DNR
5. Negative image Function
Weather proof IP66
MDC-6xxx , MDC-8xxx MODEL
External Focus & Focal Length Adjustment
77Ø, 88Ø Series (MDC-6220VTD-35H, 36H, 45, 48)
Dual(Surface / Flush) Mount Type Vandal Proof Dome Camera
MDC-8xxx MODEL
1. The unit is installed by two types of installation with flush or surface
mount. When the camera is installed with flush mount, the unit can be
installed into an existing two-gang junction box.
2. Surface or Flush Mounting using the supplied surface mount bracket.
C / CS Mount Lens Adjustable
MDC-4xxx MODEL
UTC Remote Controller
- Long distance controller.
- Menu can be adjusted without opening the camera case.
- It is of conveniently portable size.
1. Camera
2. Auto IRIS Lens Connection Plug
3. L-WRENCH
4. C - Mount Adaptor
5. Manual
COMPONENTS
'&9,1
32:(5
,5,6-$&.
9,'(2287
'&
9,'(2
6(7
)*
w
D
H
Width Height depth
64 58 102
16 MICRODIGITAL
COMPONENTS
Over view
3Back focus clamp screw & Hole
4Mount bracket
1Lens protection cap
2CS-MOUNT Lens adaptor
1 Lens protection cap
Cover the lens when not in use.
2 CS-mount lens adaptor
Attach the CS-mount lens here, and if you want to use C-mount lens, also please
attach C-ring to the CS-mount and then also
3 Back focus clamp screw
Loosen the clamp screw with a L-Wrench before adjusting the Back Focal length.
4 Mount bracket
Use the screw holes provided when fixing the camera onto a mounting bracket.
The mounting bracket can be attached to either the bottom or the top of the camera.
Rear view
1 Auto iris lens connector
Connection terminal for an auto iris lens.
2 Auto iris lens selection switch
Used to change between DC or Video depending upon the type of auto iris in use.
3 Video output terminal
Sends video signals and connects to the video input terminal of the monitor.
4 Power lamp
Lights up when the correct power is supplied to the camera.
5 OSD button
6 Power input terminal : Low voltage power connection.
7 AC Power Cord : Accept AC90~240V-50Hz/60Hz
MDC-4xx0/ 4xx1
DC 12V IN
AC 24V IN
POWER
IRIS JACK VIDEO OUT
DC
VIDEO
SET
F.G
AC24V / DC12V
POWER
IRIS JACK VIDEO OUT
DC
VIDEO
SET
F.G
AC230V
1
4
6
5
2 3 1
4
7
5
2 3
MDC-4220C / CTD
MICRODIGITAL 17
COMPONENTS
1 Lens protection cap
Cover the lens when not in use.
2 CS-mount lens adaptor
Attach the CS-mount lens here, and if you want to use C-mount lens, also please
attach C-ring to the CS-mount and then also
3 Back focus clamp screw
Loosen the clamp screw with a L-Wrench before adjusting the Back Focal length.
4 Mount bracket
Use the screw holes provided when fixing the camera onto a mounting bracket.
The mounting bracket can be attached to either the bottom or the top of the camera.
Rear view
1 Auto iris lens connector
Connection terminal for an auto iris lens.
2 Auto iris lens selection switch
Used to change between DC or Video depending upon the type of auto iris in use.
3 Video output terminal
Sends video signals and connects to the video input terminal of the monitor.
4 Power lamp
Lights up when the correct power is supplied to the camera.
5 OSD button
6 Power input terminal : Low voltage power connection.
7 AC Power Cord : Accept AC90~240V-50Hz/60Hz
MDC-4xx0/ 4xx1 MDC-4xx2
Specifications and Designs are subject to change without prior notice due to improvement
DC 12V IN
AC 24V IN
POWER
IRIS JACK VIDEO OUT
DC
VIDEO
SET
F.G
AC24V / DC12V
POWER
IRIS JACK VIDEO OUT
DC
VIDEO
SET
F.G
AC230V
1
4
6
5
2 3 1
4
7
5
2 3
20 MICRODIGITAL
L
D
W
MDC-6220 VTD-20 VTD-20H
Dimension
Diameter 65ø (63.09ø)
Width 74.00
Length 146.80
IR LED & Heater 20pcs IR LED 20pcs IR-LED,
3pcs Heater
Power Consumption
Normal 130mA
IR LED ON 360mA
Heater ON X 260mA
Dimension
COMPONENTS
1 Lens
2 IR-LED / Heater (Option)
3 Zoom / Focus Lever
4 OSD Joystick (Option)
5 Cable Management Bracket
6 VBS-Extra for connecting to LCD (Option)
▶Specifications and Designs are subject to change without prior notice due to improvement
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
/
