CAUTION Capacity: 121lbs (55kg). Use with products heavier than capacity may result
in instability causing possible injury
465099 rev00
AVF Group Ltd. Hortonwood 30, Telford, Shropshire, TF1 7YE, England
AVF Incorporated 3187, Cornerstone Drive, Eastvale, CA 91752, USA
www.avfgroup.com
121lbs
55kg
CUSTOMER SERVICES HELP LINE NUMBER:
+44 (0)1952 670009 (UK)
1-800 667 0808 (USA)
##
Read through ALL instructions before commencing installation.
If you have any questions about this product or issues with installation contact
the customer services help line before returning this product to the store.
See www.avfgroup.com/unimax for instruction video.
STOP
Assembly Overview
Fit Screen Hangers to TV
Fitting the Wall Bracket
Hanging the TV
Index
Retain all packaging in case the bracket needs to be returned.
Contents may vary from photography / Illustrations.
You will not need all these parts, so expect there to be some left over depending upon the
specification of your TV.
This product is intended for indoor use only. Use of this product outdoors could lead to
failure and personal injury.
It is the responsibility of the installer to ensure that the mounting wall is of a suitable
standard and void of any services (eg gas, electricity, water etc).
AVF accept no responsibility for any damage or loss caused by installing this product in a
sub standard wall.
Marking Wall For Drill Points
5
Assemble Positioning Template
3
Fit Screen Hangers to TV
2
Measure the TV fixing holes Width and Height
1
Determine Bracket Hole Centers
4
Fitting the Wall Bracket
6
Fitting the Wall Bracket Covers
7
Hanging the TV
8
Boxed Parts
Tools Recommended
Stud Finder
Ø3mm (1/8") Wood
Ø10mm (25/64") Masonry
Ø5.5mm (7/32") Masonry
Ø3.5mm (9/64") Metal
A1
A
U2
U1
B1
B
Dx2
Cx2
TV Screws, Reducers and Spacers
F1x4
F2x4
F3x4
E1x12
E2x4
Hx4 Jx8
Lx2 Mx4 Nx4 Ox2
Px2
Qx2 R T
S
16mm
M5
25mm
M5
45mm
M5
16mm
25mm
45mm
M6 M6 M6
M8 M8 M8
16mm
25mm
45mm
16mm
M4
G1x4
G4x4 G5x4 G6x4
G7x4
G10 x4
G8x4
G11 x4
G9x4
G12 x4
!
Take Care
Remove the Wall Bracket Covers and keep for step 7
i
ii
Wall bracket covers A1 & B1 are removed in the same way.
Measure the TV fixing holes Width and Height
1
TV Fixing Holes
200mm to infinity
100mm to infinity
X
Y
If width X is less than 200mm or height Y is
STOP installation now and contact the customer help line
less than 100mm
!
You are provided with 4 diameters of TV fixing screws, M4, M5, M6 and
M8. Determine the screw diameter that fits and remember for step 2.
After completing step 2 you will have TV fixing screws left over,
please keep for future reference
!
G7-G9
G4-G6
G1
M8 =
M6 =
M4 =
M5 =
G10-G12
Fit Screen Hangers to TV
2
Once you have established which screw diameter you need for your TV you will need to choose
which wall spacing you require. Check the back of your TV and use the OPTION that fits your TV.
Please see page opposite for more details.
OPTION 1
12mm Wall Space
OPTION 2
20mm Wall Space
OPTION 3
40mm Wall Space
Suitable for TVs with a flat
back and no obstructions
Suitable for TVs with small
to medium obstructions eg
power supply, mouldings etc
Suitable for TVs with large
obstructions eg power
supply, mouldings etc
12mm 20mm 40mm
TV TV TV
E2
TV
TV
Problem
Not enough screw
engagement
Solution
Red spacer
has replaced
spacer
E2
E1
E1
Top
Bottom Fixings
If required
Top Fixings
F1-F3
G1-G12
C
If required E1
G1-G12
If required
F1-F3
D
If required
E1
In certain circumstances it may be necessary to use
red spacer E2 as either a replacement or addition to
spacer E1.
When is it necessary to use red spacers E2?
It is recommended that when fitting Hangers C and
Stand-offs D to your TV you have at least 5-10mm of
screw engagement. In certain circumstances you may
need to use red spacers E2 as either a replacement,
or together with spacers E1 to achieve this. Whenever
you use red spacers E2 you must use all 4 provided.
C C CDD D
E1E1E1E1E1E1
E1E1E1E1E1E1
E1E1E1E1E1E1
F2F3F2F3
G6G6G9G9G12 G12
C D
C DC D
E1E1
E1E1E1E1
F2F3
G5G8G11
F2F3
G5G8G11
C DC DC DC D
F1F1F2F2F3F3
G1G1G4G4G7G7G10 G10
OPTION 1
12mm Wall Space
Top Fixings
M4 M5 M6 M8
Bottom Fixings
M4 M5 M6 M8
TopFixings
M5 M6 M8
Bottom Fixings
M5 M6 M8
Top Fixings
M5 M6 M8
Bottom Fixings
M5 M6 M8
This OPTION is not suitable
for M4 screws G1
OPTION 2
20mm Wall Space
This OPTION is not suitable
for M4 screws G1
OPTION 3
40mm Wall Space
Assemble Positioning Template
3
Top
The center line of the
template represents
the center of your TV.
U2
Lay the template on the back of the TV and follow the instructions below.
Line up with top
of the screen.
Cut the template so it is flush with
the bottom of your TV so that when the
template is on the wall you can see
exactly where your TV will be vertically
(distance from the floor and ceiling).
U2
U2
U1
Determine Bracket Hole Centers
4
U1
U2
C
Top row holes
If hangers C do not line up with any holes on the template then ensure template is
firmly in position and punch 2 holes to match your top fixing centres with a pencil or
sharp object.
Place the top row of holes on
template U1 over hangers C.
Mark off the top fixing centres
Marking Wall For Drill Points
5
Use your template to mark
two points on the wall that
correspond with the top
fixing centers of your TV.
Represents the
top of your TV. T
Represents the
bottom of your TV.
Represents the
center of your TV.
DRILL POINTS
T
Next, use the Wall Brackets and as a template and position them over the appropriate
PENCIL MARKS you have made, so that the mark is in the middle of the
CENTRAL HOLE of the Wall Bracket. Ensure the bracket is level and mark the three
DRILL POINTS with a pencil. Repeat for other bracket.
A B
Drill six 3mm pilot holes and select appropriate fixings (see section 6)
B
DRILL POINTS
A B
A
Before marking the wall,
determine the wall type that
you have (i.e. Solid Wall/
Drywall/Wood Stud/
Metal Stud).
Ensure the drilling area is
free from mains services
(Gas/Electric/Water).
Represents the
center of your TV.
PENCIL MARK
CENTRAL HOLE
PENCIL MARK
CENTRAL HOLE
Fitting the Wall Bracket
6
Use the correct fixings for your wall type. Mixing fixing screws may be required for
installations that span different wall types. DO NOT OVER TIGHTEN SCREWS.
Solid Wall
10mm (25/64")
40mm (19/16")
5.5mm (7/32")
N
O
N
M
Q
M
Remove dust
from holes
Lubricate screw
thread with soap
12.5 mm (½") MAX
75mm (3")
A+B
Solid
Concrete
Drywall
18mm (3/4")
R
R
40mm
(19/16")
MIN gap
Remove dust from holes
A+B
O
Jx2
J
PSelf
drilling
i
ii
iii
H
S
Min supporting surface specification:- ½” thick
drywall, mounted on 1½” x 3½” wood stud at
16" centers.
Turn until
secure do not
over tighten
Wood Stud Metal Stud
18mm (3/4") 18mm (3/4")
R R
3mm
(1/8") 3.5mm
(9/64")
75mm (3")
Ensure hole is
in the middle of
the wood stud
P P
Self
drilling
Self
drilling
Use Drywall Fixing H
O O
Lubricate screw
thread with soap
A+B A+B
J J
N L
Only one fixing will be in the wood stud. The
other fixings will be in drywall (see above)
Only one fixing will be in the metal stud. The
other fixings will be in drywall (see above)
Min supporting surface specification:-
½” thick drywall
Use Drywall Fixing H
0.6mm (0.025") MIN stud thickness
Min supporting surface specification:-
½” thick drywall
Fitting the Wall Bracket Covers
7
A1+B1
On wall bracket covers A1 & B1 are 3 retaining tabs. These locate onto 3 retaining lips
on wall brackets A & B and lock the wall bracket covers in position.
Retaining tab
Retaining tab
Retaining tab
A+B
Retaining lip
Retaining lip
Retaining lip
A1+B1
A+B
A1+B1
A+B
Hanging the TV
8
If required you can adjust the level
of your TV by moving from side to side
iii
iii iv
Removing the TV
This is a two person job. To remove the TV reverse the movements as shown above.
A
C
B
C
Hanging the TV is a two person job.
Present hangers (on the back of the TV) to the opening on brackets A & B. Slide down
and across into place. Ensure both hangers are fully engaged. If cables from the TV
prevent the TV resting against the wall then an alternative hanger configuration will be
required (see section 2).
TV must be parallel to wall. Use spacers / stand-offs as shown in section 2.
C
Removing the Wall Bracket Covers
Should you want to remove the wall bracket covers please follow the steps below.
i
ii
iii
A1+B1
A1+B1
A1+B1
Keep screwdriver level
as you pull downwards
!
Take Care
/
