465091 rev00
AVF Group Ltd. Hortonwood 30, Telford, Shropshire, TF1 7YE, England
AVF Incorporated 3187, Cornerstone Drive, Eastvale, CA 91752, USA
www.avfgroup.com
121lbs
55kg
CUSTOMER SERVICES HELP LINE NUMBER:
+44 (0)1952 670009 (UK)
1-800 667 0808 (USA)
##
Read through ALL instructions before commencing installation.
If you have any questions about this product or issues with installation contact
the customer services help line before returning this product to the store.
See www.avfgroup.com/unimax for instruction video.
STOP
Assembly Overview
Fit Screen Hangers to TV
Fitting the Wall Bracket
Hanging the TV
Retain all packaging in case the bracket needs to be returned.
Contents may vary from photography/ Illustrations.
You will not need all these parts, so expect there to be some left over depending upon the
specification of your TV.
This product is intended for indoor use only. Use of this product outdoors could lead to
failure and personal injury.
It is the responsibility of the installer to ensure that the mounting wall is of a suitable
standard and void of any services (eg gas, electricity, water etc).
AVF accept no responsibility for any damage or loss caused by installing this product in a
sub standard wall.
Index
Marking Wall For Drill Points
5
Assemble Positioning Template
3
Fit Screen Hangers to TV
2
Measure the TV fixing holes Width and Height
1
Determine Bracket Hole Centres
4
Fitting the Wall Bracket
6
Fitting the Wall Bracket Covers
7
Hanging the TV
8
Tilt Position only
Marking Wall For Drill Points
13
Assemble Positioning Template
10
Fit Tilt Brackets to TV
12
Determine Bracket Hole Centres
11
Fitting the Wall Bracket
14
Fitting the Wall Bracket Covers
15
Hanging the TV
16
Flat to wall only
Choose Tilt
9
Boxed Parts
Tools Recommended
Stud Finder
Ø3mm (1/8") Wood
Ø10mm (25/64") Masonry
Ø5.5mm (7/32") Masonry
Ø3.5mm (9/64") Metal
U2
U1
A1
A
B1
B
D
x2
C
x2
V
x2
X
x2
W
x2
TV Screws, Reducers and Spacers
F1
x4
F2
x4
F3
x4
E1
x12
E2
x4
H
x4
I
x4
J
x8
K
x4
L
x2
M
x4
N
x4
O
x2
P
x2
Q
x2
R T
S
25mm
M4
45mm
M4
16mm
M5
25mm
M5
45mm
M5
16mm
25mm
45mm
M6 M6 M6
M8 M8 M8
16mm
25mm
45mm
16mm
M4
G1
x4
G4
x4
G2
x4
G5
x4
G3
x4
G6
x4
G7
x4
G10
x4
G8
x4
G11
x4
G9
x4
G12
x6
!
Take Care
Remove the Wall Bracket Covers and keep for step 7 or 15
i
ii
Wall bracket covers A1 & B1 are removed in the same way.
Measure the TV fixing holes Width and Height
1
TV Fixing
Holes
200mm to infinityX
If width X is less than 200mm or height Y is
STOP installation now and contact the customer help line
less than 100mm
!
You are provided with 4 diameters of TV fixing screws, M4, M5, M6 and
M8. Determine the screw diameter that fits and remember for step 2 or 12.
G7-G9
G4-G6
G1-G3
M8 =
M6 =
M4 =
M5 =
G10-G12
100mm to infinityY
Tilt
Flat
200mm to infinityX
100mm to 400mmY
Tilt
Flat
Flat to Wall or Tilt Position
Before you start please choose if you would like your TV to be either Flat
to Wall or in a Tilt Position.
Flat to Wall
Follow steps 2 - 8
Tilt Position
Follow steps 9 - 16
After completing step 1 you will have TV fixing screws left over,
please keep for future reference
!
Fit Screen Hangers to TV
2
Once you have established which screw diameter you need for your TV you will need to choose
which wall spacing you require. Check the back of your TV and use the OPTION that fits your TV.
Please see page opposite for more details.
OPTION 1
12mm Wall Space
OPTION 2
20mm Wall Space
OPTION 3
40mm Wall Space
Suitable for TVs with a flat
back and no obstructions
Suitable for TVs with small
to medium obstructions eg
power supply, mouldings etc
Suitable for TVs with large
obstructions eg power
supply, mouldings etc
12mm 20mm 40mm
TV TV TV
Top
Bottom Fixings
If required
Top Fixings
F1-F3
G1-G12
C
If required
E1
G1-G12
If required
F1-F3
D
If required
E1
Flat to Wall only
E2
TV
TV
Problem
Not enough screw
engagement
Solution
Red spacer
has replaced
spacer
E2
E1
E1
In certain circumstances it may be necessary to use
red spacer E2 as either a replacement or addition to
spacer E1.
When is it necessary to use red spacers E2?
It is recommended that when fitting Hangers C and
Stand-offs D to your TV you have at least 5-10mm of
screw engagement. In certain circumstances you may
need to use red spacers E2 as either a replacement,
or together with spacers E1 to achieve this. Whenever
you use red spacers E2 you must use all 4 provided.
D
C
C C
C
D
D D
E1
E1 E1
E1
E1
E1
E1 E1
E1
E1 E1
E1
E1
E1
E1 E1
E1
E1 E1
E1
E1
E1
E1 E1
F1
F2 F3
F1
F2
F3
G3
G3
G6 G6G9
G9G12 G12
C
DC D
C DC D
E1
E1E1 E1
E1 E1E1 E1
F1
F2
F3
G2
G5
G8 G11
F1 F2
F3
G2 G5
G8 G11
C DC DC DC D
F1 F1F2 F2F3 F3
G1 G1G4 G4G7 G7G10 G10
OPTION 1
12mm Wall Space
OPTION 2
20mm Wall Space
OPTION 3
40mm Wall Space
Top Fixings
M4 M5 M6 M8
Bottom Fixings
M4 M5 M6 M8
Top Fixings
M4 M5 M6 M8
Bottom Fixings
M4 M5 M6 M8
Top Fixings
M4 M5 M6 M8
Bottom Fixings
M4 M5 M6 M8
Assemble Positioning Template
3
U2
U1
Determine Bracket Hole Centres
4
Flat to Wall only
Flat to Wall only
Top
The centre line of the
template U2 represents
the centre of your TV.
Lay the template on the back of the TV and follow the instructions below.
Line up with top
of the screen.
Cut the template U2 so it is flush with
the bottom of your TV so that when the
template is on the wall you can see
exactly where your TV will be vertically
(distance from the floor and ceiling).
If hangers C do not line up with any holes on the template then ensure template is
firmly in position and punch 2 holes to match your top fixing centres with a pencil or
sharp object.
U1
U2
C
Place the top row of holes on
template U1 over hangers C.
Mark off the top fixing centres
Top row holes
Marking Wall For Drill Points
5
Use your template to mark
two points on the wall that
correspond with the top
fixing centres of your TV.
Represents the
top of your TV.
T
Represents the
bottom of your TV.
Represents the
centre of your TV.
DRILL POINTS
T
Next, use the Wall Brackets and as a template and position them over the appropriate
PENCIL MARKS you have made, so that the mark is in the middle of the
CENTRAL HOLE of the Wall Bracket. Ensure the bracket is level and mark the three
DRILL POINTS with a pencil. Repeat for other bracket.
A B
Drill six 3mm pilot holes and select appropriate fixings (see section 6)
B
DRILL POINTS
A B
A
Before marking the wall,
determine the wall type that
you have (i.e. Solid Wall/
Dot & Dab/ Plasterboard/
Wood Stud/Metal Stud).
Ensure the drilling area is
free from mains services
(Gas/Electric/Water).
Flat to Wall only
Represents the
centre of your TV.
PENCIL MARK
CENTRAL HOLE
PENCIL MARK
CENTRAL HOLE
I
P
Fitting the Wall Bracket
6
Use the correct fixings for your wall type. Mixing fixing screws may be required for
installations that span different wall types. DO NOT OVER TIGHTEN SCREWS.
Solid Wall
10mm (25/64")
40mm (19/16")
5.5mm (7/32")
N
O
N
M
Q
M
Remove dust
from holes
Lubricate screw
thread with soap
12.5 mm (½") MAX
75mm (3")
K
Lubricate screw
thread with soap
K
I
10mm (25/64")
108mm (41/4")
If gap is above 40mm (19/16) use
plasterboard fixing method
Self drilling
40mm (19/16")
MAX gap
Dot & Dab
Remove dust from holes
A+B
A+B
O
Flat to Wall only
Plasterboard Wood Stud
Metal Stud
18mm (3/4")
R
R
40mm (19/16")
MIN gap
Remove dust
from holes
P
Self drilling
i
ii
iii
H
S
18mm (3/4") 18mm (3/4")
R R
3mm
(1/8")
3.5mm
(9/64")
75mm (3")
Ensure hole is in the middle
of the wood stud
P P
Self
drilling
Self
drilling
Use Plasterboard
Fixing H
Use Plasterboard
Fixing H
O O
Lubricate screw
thread with soap
A+B A+B
J J
N L
Only one fixing will be in the
wood stud. The other fixings will
be in plasterboard (see above)
Only one fixing will be in the
metal stud. The other fixings will
be in plasterboard (see above)
O
J
x2
J
A+B
Turn until secure
do not over tighten
Fitting the Wall Bracket Covers
7
A1+B1
On wall bracket covers A1 & B1 are 3 retaining tabs. These locate onto 3 retaining lips
on wall brackets A & B and lock the wall bracket covers in position.
Retaining tab
Retaining tab
Retaining tab
A+B
Retaining lip
Retaining lip
Retaining lip
A1+B1
A+B
A1+B1
A+B
Flat to Wall only
Hanging the TV
8
If required you can adjust the level
of your TV by moving from side to side
i
ii
iii
iv
A
C
B
C
Removing the TV
This is a two person job. To remove the TV reverse the movements as shown above.
Hanging the TV is a two person job.
Present hangers (on the back of the TV) to the opening on brackets A & B. Slide down
and across into place. Ensure both hangers are fully engaged. If cables from the TV
prevent the TV resting against the wall then an alternative hanger configuration will be
required (see section 2).
TV must be parallel to wall. Use spacers / stand-offs as shown in section 2.
C
Flat to Wall only
Choose Tilt
9
You can choose between 2 different tilt positions, either 4 or 8°.°
4 tilt°
8 tilt°
Use your fingertip
to hold nyloc nut V
steady while you
tighten screw G12
Ensure a flush fit between tilt bracket W
and spacer X by lining up the notch and
pip correctly
V
C
X
W
G12
V
C
G12
W
Use your fingertip
to hold nyloc nut V
steady while you
tighten screw G12
If you have chosen 8° tilt option and your TV size is 65" or over it will be necessary to add
spacers to prevent your TV clashing with the wall, the size of your TV will determine if you
need to use 1 or 3 spacers. Please see below for an example.
Spacers are used between tilt bracket
and TV to prevent clash with wall
E1 W
Clash
No Clash
X
W
Notch Pip
W
W
Tilt Position only
x2 x2
Assemble Positioning Template
10
Top
Lay the template on the back of the TV and follow the instructions below.
Line up with top
of the screen.
U2
U1
Determine Bracket Hole Centres
11
Tilt Position only
Tilt Position only
The centre line of the
template U2 represents
the centre of your TV.
Cut the template U2 so it is flush with
the bottom of your TV so that when the
template is on the wall you can see
exactly where your TV will be vertically
(distance from the floor and ceiling).
U1
U2
Place the top row of holes
on template U1 over top TV
fixing holes.
Mark off the top fixing centres
If top TV fixing holes do not line up with any holes on the template then ensure
template is firmly in position and punch 2 holes to match your top fixing centres with
a pencil or sharp object.
Top row holes
Fit Tilt Brackets to TV
12
Once you have established which screw diameter you need for your TV you will need to choose
which wall spacing you require. Check the back of your TV and use the OPTION that fits your TV.
Please see page opposite for more details.
OPTION 1
12mm Wall Space
OPTION 2
20mm Wall Space
OPTION 3
40mm Wall Space
Suitable for TVs with a flat
back and no obstructions
Suitable for TVs with small
to medium obstructions eg
power supply, mouldings etc
Suitable for TVs with large
obstructions eg power
supply, mouldings etc
12mm 20mm 40mm
TV TV TV
It is recommended that when fitting Tilt Brackets W to
your TV you have at least 5-10mm of screw
engagement. In certain circumstances you may
need to use red spacers E2 as either a replacement,
or together with spacers E1 to achieve this. Whenever
you use red spacers E2 you must use all 4 provided.
Bottom Fixings
If required
Top Fixings
F1-F3
G1-G12
If required
G1-G12
If required
F1-F3
If required
E1
Top
E1
Tilt Position only
W
W
E2
TV
TV
Problem
Not enough screw
engagement
Solution
Red spacer
has replaced
spacer
E2
E1
E1
In certain circumstances it may be necessary to use
red spacer E2 as either a replacement or addition to
spacer E1.
When is it necessary to use red spacers E2?
WWWW
F1 F2 F3
W W W W
WWWW
F1 F2 F3
E1
E1 E1
E1
E1
E1
E1 E1
E1
E1 E1
E1
E1
E1
E1 E1
E1
E1 E1
E1
E1
E1
E1 E1
F1
F2 F3
G3
G3
G6 G6G9
G9G12 G12
E1
E1E1 E1
E1 E1E1 E1
F1
F2
F3
G2
G5
G8 G11
G2 G5
G8 G11
WWWW
F1 F1F2 F2F3 F3
G1 G1G4 G4G7 G7G10 G10
OPTION 1
12mm Wall Space
OPTION 2
20mm Wall Space
OPTION 3
40mm Wall Space
Top Fixings
M4 M5 M6 M8
Bottom Fixings
M4 M5 M6 M8
Top Fixings
M4 M5 M6 M8
Bottom Fixings
M4 M5 M6 M8
Top Fixings
M4 M5 M6 M8
Bottom Fixings
M4 M5 M6 M8
W W W W
W W W W
Marking Wall For Drill Points
13
Use your template to mark
two points on the wall that
correspond with the top
fixing centres of your TV.
Represents the
top of your TV.
Represents the
bottom of your TV.
Represents the
centre of your TV.
Before marking the wall, determine the wall type that you have
(i.e. Solid Wall/Dot & Dab/ Plasterboard/Wood Stud/Metal Stud).
Ensure the drilling area is free from mains services (Gas/Electric/Water).
Tilt Position only
!
Use the marks on the top row that you made in step 11 and make
the same marks on the bottom row. You will use the marks on the
bottom row to make 2 pencil marks on the wall.
Top row marks
Bottom row
T
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
Other documents
-
MODONA 7754-A Installation guide
-
MODONA 6260-A Installation guide
-
MODONA 4060-RB Installation guide
-
MODONA 4054-RB Installation guide
-
MODONA 9954-A Installation guide
-
AVF NUL201-A Operating instructions
-
OWI CRS301 INFRARED WIRELESS MIC SYSTEM Operating instructions
-
MONDOLUX MD68 User manual
-
-
Farnell PS-UTTS32B User manual
