Xtreme XPC-2POSTL User manual
- Category
- Rack accessories
- Type
- User manual
XPC-2POSTL Rack Soluon
For use with XPC Rack Models of UPS or Baery Packs
User & Installaon Manual
www.xpcc.com | © 2014 Xtreme Power Conversion Corporaon. All rights reserved. (Rev 9/10/14)
Xtreme Power Conversion Corporaon
XPC-2POSTL User’s Manual
Page 2
Rack Soluon
Table of Contents
Descripon...................................................................................................3
Kit Contents.................................................................................................4
Installaon Instrucons................................................................................4
Aach Shelf to Rack.........................................................................................................................4
Technical Specicaons................................................................................5
XPC-2POSTL Rack Shelf Diagram...................................................................6
Xtreme Power Conversion Corporaon
XPC-2POSTL User’s Manual
Page 3
Rack Soluon
Descripon
The XPC-2POSTL Rack Soluon is compable with most 19” EIA standard 2 post racks. The 2 post rack shelf has a
150 lbs equipment capacity and will support a wide variety of electronic equipment. Devices up to 25” in depth
can be supported on this 2 post rack shelf.
Vented Aach to any rack hole
(2 posions per U space)
Front/rear anges
Up or down
19” wide at front/back
(17.7” opening in center)
Durable power coated
black nish
2U aachment mounts.
Can mount upside down
Strong 16GA steel
150 lbs capacity
Xtreme Power Conversion Corporaon
XPC-2POSTL User’s Manual
Page 4
Rack Soluon
Kit Contents
(1) Shelf
(8) 12-24 Pan Head Screws
(8) 10-32 Pan Head Screws
Installaon Instrucons
Aach Shelf to Rack
Line up 2 holes in each aachment ange and bolt to rack in desired posion using the 10-32 Pan Head Screws.
Make sure that your rack is securely aached and anchored to the oor.
Once the shelf is securely aached to the rack, carefully place the UPS into the shelf. The weight of the UPS might
require two people to perform this funcon. Make sure that the UPS is centered on the shelf, both side-to-side
and front-to-back.
It is always advisable to install the UPS in the lower poron of the rack to assure stability.
Please follow all installaon instrucons is the manufactures equipment manual for the equipment to be installed
on the shelf.
Xtreme Power Conversion Corporaon
XPC-2POSTL User’s Manual
Page 5
Rack Soluon
Technical Specicaons
Rack Type EIA 19" standard 2 Post racks
Rack Type 2 Post-L (Light duty)
Rack Units 3U
Weight Capacity 150 lbs
Equipment Depth
Supports equipment up to 29” (736 mm). The equipment can be deeper
than the rack mount shelf as long
as the equipment is installed on the opposite side of the anges. The
anges increase load capacity and prevent equipment movement.
Mounng Depth Range Compable with 2Post racks with 3" (76.2 mm) side posts
Overall Installaon Depth 20"
Shelf Surface Area 17.7" x 20"
Shelf Type Vented
Finish Black textured powder coat
Included Hardware 10-32 & 12-24 pan head screws
Hole Type
10-32 or 12-24 threaded holes
Square hole relay racks will require cage nuts
Assembly Notes Phillips head screwdriver required
Tech Notes Shelf depth is measured from front to rear including anges
Xtreme Power Conversion Corporaon
XPC-2POSTL User’s Manual
Page 6
Rack Soluon
XPC-2POSTL Rack Shelf Diagram
19.00
3.05 8.56
19.89
Usable Depth
Flange Up
20.00
Usable Depth
Flange Down
17.77
Usable Depth
18.312
3.29
2.79
0.50
-
1
-
2
-
3
-
4
-
5
-
6
Xtreme XPC-2POSTL User manual
- Category
- Rack accessories
- Type
- User manual
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
