2. Computers & electronics
  3. Computer components
  4. Chassis components
  5. Racks
  6. Rack accessories
  7. Xtreme
  8. XPC-2POST

Xtreme XPC-2POST User manual

  • Hello! I am an AI chatbot trained to assist you with the Xtreme XPC-2POST User manual. I’ve already reviewed the document and can help you find the information you need or explain it in simple terms. Just ask your questions, and providing more details will help me assist you more effectively!
XPC-2POST Rack Soluon
For use with XPC Rack Models of UPS or Baery Packs
User & Installaon Manual
www.xpcc.com | © 2014 Xtreme Power Conversion Corporaon. All rights reserved. (Rev 10/28/14)
Xtreme Power Conversion Corporaon
XPC-2POST User’s Manual
Page 2
Rack Soluon
Table of Contents
Descripon...................................................................................................3
Kit Contents.................................................................................................4
Installaon Instrucons................................................................................4
Aach Shelf to Rack.........................................................................................................................4
Technical Specicaons................................................................................5
XPC-2POST Rack Shelf Diagram......................................................................6
Xtreme Power Conversion Corporaon
XPC-2POST User’s Manual
Page 3
Rack Soluon
Descripon
The XPC 2 Post Rack Soluon is compable with most 19” EIA standard 2 Post racks. The 2 post rack shelf has a 300
lbs equipment capacity and will support a wide variety of electronic equipment. Devices up to 29” in depth can be
supported on this 2 post rack shelf.
Vented Aach to any rack hole
(2 posions per U space)
Front/rear anges
Up or down
19” wide at front/back
(17.7” opening in center)
Durable power coated
black nish
2U aachment mounts.
Can mount upside down
Strong 16GA steel
300 lbs capacity
Xtreme Power Conversion Corporaon
XPC-2POST User’s Manual
Page 4
Rack Soluon
Kit Contents
(1) Shelf
(12) 12-24 Pan Head Screws
(12) 10-32 Pan Head Screws
Installaon Instrucons
Aach Shelf to Rack
Line up 3 holds in each aachment ange and bolt to rack in desired posion using the 10-32 Pan Head Screws.
Aach Shelf to Rack
Make sure that your rack is securely aached and anchored to the oor.
Once the shelf is securely aached to the rack, carefully place the UPS into the shelf. The weight of the UPS might
require two people to perform this funcon. Make sure that the UPS is centered on the shelf, both side-to-side
and front-to-back.
It is always advisable to install the UPS in the lower poron of the rack to assure stability.
Please follow all installaon instrucons is the manufactures equipment manual for the equipment to be installed
on the shelf.
Xtreme Power Conversion Corporaon
XPC-2POST User’s Manual
Page 5
Rack Soluon
Technical Specicaons
Rack Type EIA 19" standard 2Post racks
Rack Type 2Post
Rack Units 3U
Weight Capacity 300 lbs (136 kgs)
Equipment Depth
Supports equipment up to 29” (736 mm). The equipment can be deeper
than the rack mount shelf as long as the equipment is installed on the
opposite side of the anges. The anges increase load capacity and pre-
vent equipment movement.
Mounng Depth Range Compable with 2Post racks with 3" (76.2 mm) side posts
Overall Installaon Depth 29" (736.6 mm)
Shelf Surface Area 17.7" x 29" (450 mm x 736.6 mm)
Shelf Type Vented
Finish Black textured powder coat
Included Hardware 10-32 & 12-24 pan head screws
Hole Type
10-32 or 12-24 threaded holes
Square hole relay racks will require cage nuts
Assembly Notes Phillips head screwdriver required
Tech Notes Shelf depth is measured from front to rear including anges
Xtreme Power Conversion Corporaon
XPC-2POST User’s Manual
Page 6
Rack Soluon
XPC-2POST Rack Shelf Diagram
19.00
3.05 13.06
28.89
Usable Depth
Flange Up
29.00
Usable Depth
Flange Down
17.78
Usable Dept
h
18.312
5.17
4.54
0.63
/