Dedicated Micros 2060 User guide

Brand: Dedicated Micros

Model: 2060

Type: User guide

This manual is also suitable for

2060 PTZ Dome

Dedicated Micros 2060 PTZ Dome is a high-quality surveillance camera with pan, tilt, and zoom capabilities. It is ideal for use in a variety of security applications, including:

Perimeter surveillance
Traffic monitoring
Crowd control
Remote monitoring

The camera features a 1/4-inch CCD sensor that provides clear and detailed images, even in low-light conditions. The pan, tilt, and zoom functions allow you to easily track moving objects or zoom in on specific areas of interest. The camera also has a built-in microphone that allows you to record audio along with video.

Dedicated Micros 2060 PTZ Dome is a high-quality surveillance camera with pan, tilt, and zoom capabilities. It is ideal for use in a variety of security applications, including:

Perimeter surveillance
Traffic monitoring
Crowd control
Remote monitoring

QUICK START GUIDE

BEKNOPTE INSTELHANDLEIDING

GUIDE D'INSTALLATION RAPIDE

GUIDADI IMPOSTAZIONE RAPIDA

GUÍARÁPIDADE CONFIGURACIÓN

This product is marked with the CE symbol and indicates

compliance with all applicable directives.

Directive 89/336/EEC.

A “Declaration of Conformity” is held at Dedicated Micros Ltd.,

11 Oak Street, Swinton, Manchester, M27 4FL.

INSTALLATION:

Full installation details are given in the Dennard 2060 Operation Manual, but these notes should get

you started.

The Dennard 2060 arrives in a large box containing the dome plus the power supply box (this box

can also house the optional 8 channel alarm card or drx external protocol converter card). Any

mounting bracket will be boxed separately.

ELECTRICAL CONNECTIONS:

The multicore cable tail from the dome comprises a co-ax, two power conductors and two RS 485

control conductors and an overall screen with drain wire.

There are some differences in wiring depending on how the dome is being controlled. Be careful to

wire to the supplied circuit or as follows.

For Dennard 2060 up the co-ax controlled units.

Bring the multicore tail from the dome into the PSU box via weatherproof glands and connect as

follows:

NOTE: The green and the yellow RS485 data wires are not used but should be parked in the

two-way terminal block provided. NOT LEFT LOOSE IN THE BOX!

For Dennard 2060 drx units.

Bring the multicore tail from the dome into the PSU box via a weatherproof cable gland and connect

it up as follows:

Co-ax

Fit a BNC connector to both incoming and outgoing co-ax cables and

join with a suitable inline connector.

Power

Connect the RED wire to the fused terminal block marked 24Va.c “L”

Connect the BLUE wire to the fused terminal block marked 24Va.c”N”

The power supply box needs a mains supply, which should be

connected to the fused terminal block marked 240Va.c.

Drain Wire Do not connect this as it is already connected at the dome end.

Co-ax

Fit a BNC connector and plug it into the “CAMERA” BNC socket on the

drx p.c.b.

Power

Connect the RED wire to the fused terminal block marked 24V a.c. “L”

Connect the BLUE wire to the fused terminal block marked 24V a.c. “N”

The power supply box needs a mains supply, which should be connected

to the fused terminal block marked 240Va.c.

Drain Wire Do not connect this as it is already connected at the dome end.

For RS485 units

Bring the multicore tail from the dome into the PSU box via weatherproof glands and connect as

follows:

The Power Supply Box needs a mains supply, which should be connected to the fused terminal

block marked 240V a.c. Fit a BNC to the incoming co-ax from the controller and connect it to the

“TELEMETRY” BNC socket on the p.c.b.

ADDRESSING THE DOME

Because the dome can be driven either up the co-ax or by RS485 it is very important to get this

setting correct.

The following settings are for up the coax control units

Columbus transmitters should be set to Baxall a/c …. standard mode, set the Dome to: Baxall

a/c panel i.e. set blue switch to F and set yellow switch to C

Baxall & Vista transmitters should be set to Baxall d/c … standard mode set Dome to: Baxall d/c

panel i.e. set blue switch to F and set yellow switch to E

Dennard, Building Block Video & Dedicated Micros transmitters should be set to BBV protocol and

the Dome should be set to: Den panel i.e. set blue switch to F and set yellow switch to D

(This is the default setting for Domes ordered as Dennard 2060 or Dennard 2060 coax)

Co-ax

Fit a BNC connector to both incoming and outgoing co-ax cables and join

with a suitable inline connector

Power

Connect the RED wire to the fused terminal block marked 24V a.c. “L”

Connect the BLUE wire to the fused terminal block marked 24V a.c. “N”

The power supply box needs a mains supply, which should be connected

to the fused terminal block marked 240Va.c.

Drain Wire Do not connect this as it is already connected at the dome end.

RS485

Connect the GREEN wire to… TX/RX - or B

Connect the YELLOW wire to… TX/RX + or A

RS485

Connect the GREEN wire to p.c.b. Grey terminal block J3 terminal C1

Connect the YELLOW wire to p.c.b. Grey terminal block J3 terminal C2

For Dennard 2060 drx units

These domes can be controlled from any controller that can be set to output BBV up the coax

protocols e.g. Dennard, Building Block Video & Dedicated Micros

The dome is addressed with the blue switch on 0 and the yellow switch on 1

(Dennard 2060 drx domes are supplied with this setting by default)

For RS485 control units

The domes need to be addressed to the camera positions and the address switch setting table can

be found in the Dennard 2060 Operation Manual.

SETTING UP PRESETS

Preset positions of 16 or less may be set up using the controller programming facility. For preset

numbers over 16 then the Dennard 2060 dome programming must be used. The controller buttons

used to achieve Dennard 2060 menu access for the more popular Controllers are shown in the

Dennard Menu System manual.

When the preset number has been keyed in an “Alphabet Menu” will appear offering you the

chance to identify that preset. To do that, select a letter by moving the cursor to a position under the

letter by using the joystick then press the keyboard “accept” command to place it on the monitor. Do

this for each letter required to spell out the location name. Finally move the cursor to Accept Entry

and press the “accept” command button(s), which will clear the menu. If identification is not

required, move the cursor directly to the Accept Entry prompt and “accept”.

BASIC TROUBLESHOOTING GUIDE

No picture

Check the PSU input and output voltages.

Check the PSU fuse.

Check the continuity on the dome multicore cable: PIN 1=Video PIN 2=Video Screen PIN

3=Data+(yellow) PIN 4=Data- (green) PIN 5=18volt neutral (blue) PIN 6=18Volt live (red) PIN

7=Earth (drain wire)

Picture with no control

If the control is via a DRX protocol converter, or any other type of protocol converter make sure the

data cables have been connected and are in the correct positions.

Check that the dome address switches are set in the correct position for the type of controller being

used.

Picture with intermittent control

This problem is often due to too much or too little video gain.

If you are using the DOME in the co-ax mode then the video levels need to be set up to 1 volt p-p.

This is achieved by accessing the Technician Menu of the dome. Select Miscellaneous Services

and from this menu select Host Comms / Video Amp and adjust lift and gain to suit.

If the dome is being controlled via an external protocol converter (DAX-DEN or DRX100) then the

dome’s internal video gain should be set to Video gain1 / normal and set the Video lift off. These

setting are accessed through the Technician Menu by selecting the Miscellaneous Services

option followed by the Video amp settings.

On Baxall controllers, alphabet menu appears when the joystick is touched.

This is because the Baxall controller has been configured to “Alternate “ mode, it should be set to

“Standard” mode with Rx as “dc”, NOT a.c.

On Dedicated Micros & BBV controllers the Dome spins continuously

This could be due to there being no “dead band” on the joystick, caused by the joystick being off

centre on power up. Power the controller down then power up again ensuring that the joystick is

free to self-centre.

To reset the dome (If the menu can be accessed)

This is done by accessing the dome Technician menu and selecting Miscellaneous services,

followed by NVM Services. Reload factory defaults will reset the dome to the original factory

settings. Note, however, that it will also remove all preset positions and tours from the memory.

This procedure should take about 40 seconds.

HELP!

UK Technical Help

Dennard Limited

55 Fleet Road

Fleet

Hants

GU51 3PN

Tel: +44 (0)1252 614884

Fax: +44 (0)1252 626013

email: sales@dennard-cctv.com

Page is loading ...

HELP!

Europese Technische Hulp

Dedicated Micros Europe Dedicated Micros France

Neckarstraße 15, 9-13 rue du Moulinet,

41836 Hückelhoven, 75013 Paris,

Germany France

Tel: +49 (0)24 33 52 58 26 Tel: +33 1 45 81 99 99

Fax: +49 24 33 52 58 20. Fax: +33 1 45 81 99 89.

e-mail: [email protected] e-mail: [email protected]

Dedicated Micros Belgium Dedicated Micros Slovenija

Joseph Chantraineplantsoen 1, Delavska cesta 26,

3070 Kortenberg, 4208 Sencur-Slovenija

Belgium

Tel: +32 2751 3480, Tel: +386 (4) 279 18 90

Fax: +32 2751 3481 Fax: +386 (4) 279 18 91

e-mail: [email protected] e-mail: [email protected]

Page is loading ...

GUIDA!

Aiuto Tecnico Europeo

Dedicated Micros Europe Dedicated Micros France

Neckarstraße 15, 9-13 rue du Moulinet,

41836 Hückelhoven, 75013 Paris,

Germany France

Tel: +49 (0)24 33 52 58 26 Tel: +33 1 45 81 99 99

Fax: +49 24 33 52 58 20. Fax: +33 1 45 81 99 89.

e-mail: [email protected] e-mail: [email protected]

Dedicated Micros Belgium Dedicated Micros Slovenija

Joseph Chantraineplantsoen 1, Delavska cesta 26,

3070 Kortenberg, 4208 Sencur-Slovenija

Belgium

Tel: +32 2751 3480, Tel: +386 (4) 279 18 90

Fax: +32 2751 3481 Fax: +386 (4) 279 18 91

e-mail: [email protected] e-mail: [email protected]

Page is loading ...

¡AYUDA!

Ayuda Técnica Europea

Dedicated Micros Europe Dedicated Micros France

Neckarstraße 15, 9-13 rue du Moulinet,

41836 Hückelhoven, 75013 Paris,

Germany France

Tel: +49 (0)24 33 52 58 26 Tel: +33 1 45 81 99 99

Fax: +49 24 33 52 58 20. Fax: +33 1 45 81 99 89.

e-mail: [email protected] e-mail: [email protected]

Dedicated Micros Belgium Dedicated Micros Slovenija

Joseph Chantraineplantsoen 1, Delavska cesta 26,

3070 Kortenberg, 4208 Sencur-Slovenija

Belgium

Tel: +32 2751 3480, Tel: +386 (4) 279 18 90

Fax: +32 2751 3481 Fax: +386 (4) 279 18 91

e-mail: [email protected] e-mail: [email protected]

Issue 4

Doc 74-0113 Rev 3.0

UK TECHNICAL HELP

Dennard Limited

Unit 4 Park Iron Works, Kingsley, Nr Bordon, Hampshire, GU35 9LY

Tel: +44 (0)1420 485713 Fax: +44 (0)1420 485714

e-mail: sales@dennard-cctv.com

EUROPEAN TECHNICAL HELP

Dedicated Micros Europe

Neckarstraße 15, 41836 Hückelhoven, Germany

Tel: +49 (0) 24 33 52 58 26 Fax: +49 (0) 24 33 52 58 20.

e-mail: [email protected]

Dedicated Micros France

9-13 rue du Moulinet, 75013 Paris, France

Tel: +33 1 45 81 99 99, Fax: +33 1 45 81 99 89.

e-mail: [email protected]

Dedicated Micros Belgium

Joseph Chantraineplantsoen 1, 3070 Kortenberg, Belgium

Tel: +32 2751 3480, Fax: +32 2751 3481

e-mail: [email protected]

Dedicated Micros Slovenija

Delavska cesta 26, 4208 Sencur-Slovenija

Tel: +386 (4) 279 18 90, Fax: +386 (4) 279 18 91

e-mail: [email protected]

www.dedicatedmicros.com

Page is loading ...

Issue 4

Doc 74-0113 Rev 3.0

UK TECHNICAL HELP

Dennard Limited

Unit 4 Park Iron Works, Kingsley, Nr Bordon, Hampshire, GU35 9LY

Tel: +44 (0)1420 485713 Fax: +44 (0)1420 485714

e-mail: sales@dennard-cctv.com

EUROPEAN TECHNICAL HELP

Dedicated Micros Europe

Neckarstraße 15, 41836 Hückelhoven, Germany

Tel: +49 (0) 24 33 52 58 26 Fax: +49 (0) 24 33 52 58 20.

e-mail: [email protected]

Dedicated Micros France

9-13 rue du Moulinet, 75013 Paris, France

Tel: +33 1 45 81 99 99, Fax: +33 1 45 81 99 89.

e-mail: [email protected]

Dedicated Micros Belgium

Joseph Chantraineplantsoen 1, 3070 Kortenberg, Belgium

Tel: +32 2751 3480, Fax: +32 2751 3481

e-mail: [email protected]

Dedicated Micros Slovenija

Delavska cesta 26, 4208 Sencur-Slovenija

Tel: +386 (4) 279 18 90, Fax: +386 (4) 279 18 91

e-mail: [email protected]

www.dedicatedmicros.com

Dedicated Micros 2060 User guide

Brand: Dedicated Micros

Model: 2060

Type: User guide

This manual is also suitable for

2060 PTZ Dome

Dedicated Micros 2060 PTZ Dome is a high-quality surveillance camera with pan, tilt, and zoom capabilities. It is ideal for use in a variety of security applications, including:

Dedicated Micros 2060 User guide

This manual is also suitable for

Dedicated Micros 2060 User guide

in other languages

Related papers

Other documents