Raymarine SeaTalk2 Owner's Handbook Manual
- Type
- Owner's Handbook Manual
This manual is also suitable for
Raymarine SeaTalk2 offers seamless integration with your E-Series display, providing intuitive control and enhanced functionality. Navigate effortlessly with waypoint management, initiate MOB procedures, and customize your display with page changes and configuration. Communicate effectively with the active window feature, access setup menus and help information, and transfer data with ease.
Raymarine SeaTalk2 offers seamless integration with your E-Series display, providing intuitive control and enhanced functionality. Navigate effortlessly with waypoint management, initiate MOB procedures, and customize your display with page changes and configuration. Communicate effectively with the active window feature, access setup menus and help information, and transfer data with ease.
D7679-1
Contents
Introduction
This handbook explains how to install, connect, operate and maintain your SeaTalk
2
Keyboard (E55061). This keyboard is also supplied with the Remote Station Kit (T82005) -
details of how to integrate these devices is given on Page 6.
Intended use
This keyboard is intended for use with Raymarine's E-Series display aboard leisure marine
boats and workboats not covered by IMO/SOLAS carriage requirements. It can be integrated
into an existing SeaTalk
2
system, if required.
Subject Page
Introduction 1
The controls 2
What's in the box? 3
Safety notices 3
Planning the installation 4
Integrating the Remote Station Kit 6
Installation 7
Accessories and spares 9
Removing/refitting 10
Maintenance 10
Important information 11
Technical support and contact details 12
www.raymarine.com
SeaTalk
2
Keyboard
Owner's Handbook
1
MENU
WPTS
MOB
DATA
ACTIVE
PAGE
OK CANCEL
IN
OUT
.
ACTIVE
WPTS
MOB
DATA
MENU
CANCELOK
9
WXYZ
8
TUV
7
PQRS
.
4
GHI
5
JKL
2
ABC
3
DEF
1
6
MNO
RANGE
PAGE
0
OUT
IN
WPTS
MOB
To manage waypoints and
initiate MOB.
MENU
To access set up
menus and help
information.
PAGE
To change page and
configure page sets.
ACTIVE
To select the
active window.
Soft keys
Press to select corresponding function
identified by on-screen label.
OK
To select on-screen option,
or return to the previous
soft key set/menu.
Range
To change the
display scale.
CANCEL
To cancel selected
on-screen option
when editing data
and to return to
previous soft key set
or menu.
Keypad
For making alpha-
numeric entries in
on-screen dialog
boxes.
Power
To turn display off and access
backlight functions and
scanner controls.
Rotary control
To scroll through lists
and edit alpha-
numeric values.
Trackpad
To control on-screen
cursor and scroll
through menu items.
DATA
To access the ruler, chart
vectors, archive and transfer,
data bar on/off functions etc.
For further details of the control functions, please refer to your E-Series Display Reference Manual.
D7702_1
2
The controls
WARNING: Navigation aid
Although this product has been
designed to be accurate and reliable,
many factors can affect its
performance. As a result, it should only
be used as an aid to navigation and
should never replace common sense and
navigational judgement. Always
maintain a permanent watch so you can
respond to situations as they develop.
WARNING: Cable
Do not disconnect the keyboard cable
from the keyboard.
WARNING: Product installation
This equipment must be installed and
operated in accordance with the
instructions contained in this handbook.
Failure to do so could result in poor
product performance, personal injury
and/or damage to your boat.
WARNING: Electrical safety
Make sure the power supply is switched
off before you make any electrical
connections.
Gasket
Template
Whats in the box?. . . .
D7701-1
Safety notices
Terminator (x2)
SeaTalk
2
power/RF ground cable (1.5m)
SeaTalk
2
cable (1.5m)
SeaTalk
2
Keyboard
5-way junction box
Drain tube (8mm x 1m)
Suncover
Clamp (x2)
Stud (x2)
Thumb nut (x2)
Cradle
Handbook
Subject Page
Introduction 1
The controls 2
What's in the box? 3
Safety notices 3
Planning the installation 4
Integrating the Remote Station Kit 6
Installation 7
Spares and accessories 9
Removing/refitting 10
Maintenance 10
Important information 11
Technical support and contact details 12
D7679-1
Contents
Introduction to the SeaTalk
2
Keyboard
This handbook explains how to install, connect, operate and maintain your SeaTalk
2
Keyboard (E55061). This keyboard is also supplied with the Remote Station Kit (T82005) -
details of how to integrate these devices is given on Page 6.
Intended use
This product is a keyboard intended for use within a SeaTalk
2
system and connected via a
junction box to Raymarine's E-Series display. The intended application is for leisure marine
boats and workboats not covered by IMO/SOLAS carriage requirements. The SeaTalk
2
keyboard is waterproof to CFR-46 standard.
www.raymarine.com
SeaTalk
2
Keyboard
Owner's Handbook
1
MENU
WPTS
MOB
DATA
ACTIVE
PAGE
OK CANCEL
I
N
O
U
T
.
3
Planning the installation
Where can the SeaTalk
2
Keyboard be mounted?
The Seatalk
2
keyboard can be flush or trunnion mounted either indoors or outdoors. It is
waterproof to CFR-46 standard.
Important:
The drain tube is not required if the keyboard is mounted indoors or in an area protected
from rain and/or sea spray. If mounting the keyboard outdoors or in an unprotected area
the drain tube will need to run to a suitable exit point below the level of the keyboard.
What configuration should I use?
How you connect the keyboard depends on the distances between your E-Series Display, the
keyboard and power source and whether or not you are connecting the keyboard to an
existing SeaTalk
2
system. Select the appropriate configuration from the following:
Configuration 1
Cable length between E-Series Display and keyboard less than 4.5m and
Not linking into an existing SeaTalk
2
system.
E-Series Display
SeaTalk
2
Keyboard
Junction box
Not supplied/accessory/
existing system
E Series display
TerminatorTerminator
SeaTalk
2
cable (1.5 m)
12v supply
Keyboard cable
(attached/3 m)
SeaTalk
2
Power/RF ground cable (1.5 m)
red
black grey
5A circuit breaker
Or:
Switch with 5A fuse
Supplied in the box
4
D7680-1
Configuration 2
Cable length between E-Series Display and keyboard exceeds 4.5m and
Not linking into an existing SeaTalk
2
system.
Configuration 3
Integrating the keyboard into an existing SeaTalk
2
system.
E-Series Display
SeaTalk
2
Keyboard
Junction box
Additional
junction box
E Series display
Terminator
Terminator
SeaTalk
2
cable (1.5m)
12v supply
SeaTalk
2
Power/RF ground cable (1.5m)
To:
Existing SeaTalk
2
system
(incorporating terminators,
power/RF ground)
To:
Existing SeaTalk
2
system
(incorporating terminators,
power/RF ground)
E-Series Display
SeaTalk
2
Keyboard
Junction box
E Series display
SeaTalk
2
cable (1.5m)
Keyboard cable (attached/3m)
SeaTalk
2
extension cable
(see 'Accessories')
SeaTalk
2
extension cable (see 'Accessories')
SeaTalk
2
extension cable
(see 'Accessories')
5A circuit breaker
Or:
Switch with 5A fuse
Not supplied/accessory/
existing system
Supplied in the box
Not supplied/accessory/
existing system
Supplied in the box
Keyboard cable
(attached/3m)
5
D7697-1
grey
red
black
SeaTalk
2
Keyboard
Alarm Alarm
Red
Black
Red
Black
VGA out cable, 5m
NOT waterproof
M1500 monitor
Junction box
Not supplied/accessory/existing system
Station 1
Station 2
No other SeaTalk
devices connected
Other SeaTalk
devices connected
SeaTalk
2
cable (1.5 m)
Keyboard cable (attached/3 m)
Remote Station Kit
VGA out cable, waterproof
(see Accessories)
Red
Black
Brown
White
White
Brown
Black
Red
Yellow
Drain
Drain
Yellow
E Series
Integrating the Remote Station Kit
SeaTalk/Alarm out cable,1.5m
Refer to
'Planning the
Installation',
diagrams on
pages 4 and 5.
Other
SeaTalk
devices
OR
OR
6
D7703-1
12v
supply
How do I install the keyboard?
1. Using self-adhesive or masking tape, fix the
template in the required position.
Note: Ensure that there are no cables or
other parts that will be damaged, when the
panel is drilled and sawn.
2. Drill a pilot hole inside the shaded area of
the template.
3. Saw around the shaded area of the template.
4. Remove the tape and the template remains.
Smooth the sawn edges with a file.
Drill
10 mm (
3
/
8
in)
drill bit
Masking or
adhesive tape
Jigsaw
File
What tools do I need to install the keyboard?
7
D7699-1
Note: Before installing the keyboard, please read 'Planning the installation' on Pages 4 & 5.
Installation
5. Peel the backing from the gasket and stick it
to the underside of the cradle.
7. If mounting the keyboard in an area
unprotected from rain and/or sea spray, fit
the drain tube and ensure that it runs to a
suitable exit point below the level of the
keyboard and the studs.
8. Fit the keyboard assembly into its housing.
With the dimples in the clamps fitting into
the nipples on the cradle, fit and secure the
clamps in place using the thumb nuts.
9. Ensuring that the power is connected last,
connect all the cables, terminators etc
in the appropriate configuration (see
'Planning the Installation' on pages 4 to 6).
Wrap any excess cable and tuck away.
Do not cut and resplice cables.
6. Finger tighten the studs into position.
8
D7700-1
Installation - continued
What spares are available? ...
Description Part no.
Cradle assembly (includes cradle, cable, drain tube, gasket and latch) R58213
Flush mount kit (includes gasket, clamps, drain tube, studs and thumb nuts) R58211
Latch R89043
Suncover R58212
What accessories are available? ...
Description Part no.
SeaTalk
2
power/RF ground cable (1.5m) E55070
Auxiliary alarm E26033
M1500 monitor kit (includes 5m VGA Out cable) E02009
Terminator E25048
Junction box E25049
SeaTalk
2
extension cables:
1 metre E25040
3 metres E25042
5 metres E25043
10 metres E25038
20 metres E25044
E-Series SeaTalk
2
cable (1.5m) E55053
VGA Out cables (waterproof):
10 metres E55055
20 metres E55056
Trunnion mount kit E05012
9
D7698-1
Accessories and spares
Removing/refitting
What routine checks and servicing can I do? ...
On a regular basis, examine all cables for signs of damage, such as chafing, cuts or nicks and
check that all cables are securely connected.
The SeaTalk
2
keyboard has no user serviceable parts.
How should I clean my keyboard? ...
Regularly clean your keyboard as follows:
1. Switch off the power.
2. Wipe the keyboard with a clean, soft cloth. To remove oily finger marks, use a spray
cleaning agent of the type used for cleaning eyeglasses or a mild detergent. Do not use
acid, ammonia based or abrasive products.
Maintenance
10
D7706-1
1. Switch off the power.
1. Position the top edge of the keyboard
under the lip of the cradle.
2. Push the bottom of the keyboard into
the cradle to engage the latch.
3. Push down at the top of the keyboard to
raise it from the cradle and lift the
it from the cradle.
How do I remove the keyboard? ...
How do I refit the keyboard? ...
2. Slide and hold the latch.
Important information
11
D7707-1
EMC conformance
All Raymarine equipment and accessories are designed to the best industry standards for
use in the recreational marine environment. The design and manufacture of Raymarine
equipment and accessories conforms to the appropriate Electromagnetic Compatibility
(EMC) standards, but correct installation is required to ensure that performance is not
compromised. For full details and installation guidelines refer to our web site at
www.raymarine.com
Warranty
To register your new Raymarine product, please take a few minutes to fill out the warranty
card. It is important that you complete the owner information and return the card to us to
receive full warranty benefits.
Your product can also be registered via our web site - www.raymarine.com
Handbook information
To the best of our knowledge, the information contained in this handbook was correct as it
went to press. Raymarine cannot accept any liability for any inaccuracies or omissions it may
contain. In addition, our policy of continuous product improvement may change
specifications without notice. As a result, Raymarine cannot accept liability for any
differences between the product and the handbook.
Waste Electrical and Electronic Equipment Directive
The Waste Electrical and Electronic Equipment (WEEE) Directive requires the
recycling of waste electrical and electronic equipment. Whilst the WEEE Directive
does not apply to some of Raymarine's products we support its policy and ask you to be
aware of how to dispose of this product.
The crossed out wheelie bin, illustrated above, and found on our product signifies that this
product should not be disposed of in general waste or landfill.
Please contact your local dealer, national distributor or Raymarine Technical Services for
information on product disposal.
Raymarine UK Limited
Quay Point, Northarbour Road,
Portsmouth, Hampshire
England PO6 3TD
Tel: + 44 (0)23 9269 3611
Fax: + 44 (0)23 9269 4642
www.raymarine.com
Raymarine Incorporated
21 Manchester Street
Merrimack, NH03054 - 4801
USA
Tel: 603-881-5200
Fax: 603-864-4756
www.raymarine.com
Document No: 81253_2
Date: June 2006
Raymarine 2006
Technical support & contact information
www.raymarine.com
Visit the Customer Support area of our website for Frequently Asked Questions, servicing
information, e-mail access to the Raymarine Technical Support Department and details of
Raymarine agents, worldwide.
Help us to help you
When requesting service, please quote the following product information:
Equipment type Model number Serial number
Europe
For technical support, service and
accessories contact:
Your authorized Raymarine dealer.
or
Technical Support
Raymarine UK Limited
Anchorage Park
Portsmouth
PO3 5TD
England
Tel: +44(0)23 9271 4713
Fax: +44(0)2392661228
United States
For accessories and parts contact:
Your authorized Raymarine dealer.
or
Raymarine Technical Services on:
1-800-539-5539 extension 2333,
or (603)-881-5200.
Opening hours:
Monday through Friday 0815 - 1700,
Eastern Standard or Eastern Daylight
Savings Time.
To verify your requirements
contact:
1-800-539-5539 extension 2444,
or (603)-881-5200.
For product repair & service
contact:
Your authorized Raymarine dealer.
or
Return the unit to:
Raymarine Product Repair Center
21 Manchester Street
Merrimack, NH03054 - 4801
1-800-539-5539
12
D7708-1
Configuration 4
Cable length between E-Series Display and keyboard less than 4.5m and
Linking into an existing combined SeaTalk/SeaTalk
2
system with ST290 DPU.
Do not connect the ST290 to the E-Series SeaTalk
2
connection.
SeaTalk
2
Keyboard
Junction box
E Series display
Terminator
Terminator
SeaTalk
2
cable
ST290 DPU
Existing
SeaTalk 2 system
Existing
SeaTalk system
SeaTalk
2
cable
SeaTalk cable
SeaTalk cable
SeaTalk cable
12v supply
SeaTalk
2
Power/RF
ground cable
5A circuit
breaker or
Switch with
5A fuse
Not supplied/accessory/
existing system
Supplied in the box
To:
Existing SeaTalk
system
(for example: GPS and
Autopilot)
To:
Existing SeaTalk
2
system
(incorporating terminators,
power/RF ground)
D8056-1
grey
red
black
SeaTalk
2
Keyboard Interim sheet 82201-1
Note:
For multiple keyboard
installations, please refer to
your local dealer or to
www.raymarine.com
Configuration 4
Cable length between E-Series Display and keyboard less than 4.5m and
Linking into an existing combined SeaTalk/SeaTalk
2
system with ST290 DPU.
Do not connect the ST290 to the E-Series SeaTalk
2
connection.
SeaTalk
2
Keyboard
Junction box
E Series display
Terminator
Terminator
SeaTalk
2
cable
ST290 DPU
Existing
SeaTalk 2 system
Existing
SeaTalk system
SeaTalk
2
cable
SeaTalk cable
SeaTalk cable
SeaTalk cable
12v supply
SeaTalk
2
Power/RF
ground cable
5A circuit
breaker or
Switch with
5A fuse
Not supplied/accessory/
existing system
Supplied in the box
To:
Existing SeaTalk
system
(for example: GPS and
Autopilot)
To:
Existing SeaTalk
2
system
(incorporating terminators,
power/RF ground)
D8056-1
grey
red
black
SeaTalk
2
Keyboard Interim sheet 82201-1
Note:
For multiple keyboard
installations, please refer to
your local dealer or to
www.raymarine.com
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
Raymarine SeaTalk2 Owner's Handbook Manual
- Type
- Owner's Handbook Manual
- This manual is also suitable for
Raymarine SeaTalk2 offers seamless integration with your E-Series display, providing intuitive control and enhanced functionality. Navigate effortlessly with waypoint management, initiate MOB procedures, and customize your display with page changes and configuration. Communicate effectively with the active window feature, access setup menus and help information, and transfer data with ease.
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
Raymarine Mouse E55061 User manual
-
-
-
Raymarine E120 Installation guide
-
-
Raymarine Base Station Installation guide
-
-
-
-
Other documents
-
Navionics 87043_1 User manual
-
Volvo Penta IPS S3G Installation And Connections
-
Meridian M1500 User guide
-
AND AD-4713 User manual
-
Meriam M1500 Analog Pressure Transmitter Product User Manual
-
NightSearcher Galaxy 12000 Professional and Powerful Rechargeable AC Work Light User manual
-
Popsockets PopSockets: Collapsible Grip & Stand for Phones and Tablets - Black User guide
