Raymarine Base Station Installation guide

Type
Installation guide

Raymarine Base Station is a device that allows you to connect your Raymarine instruments and accessories to a wireless network, enabling you to monitor and control your marine electronics from anywhere on your boat. With the Base Station, you can access data from your instruments, such as depth, speed, wind, and GPS position, on your compatible smartphone or tablet using the Raymarine mobile app. Furthermore, you can control your autopilot, switch between different instrument pages, and even create custom dashboards to display the information that is most important to you.

Raymarine Base Station is a device that allows you to connect your Raymarine instruments and accessories to a wireless network, enabling you to monitor and control your marine electronics from anywhere on your boat. With the Base Station, you can access data from your instruments, such as depth, speed, wind, and GPS position, on your compatible smartphone or tablet using the Raymarine mobile app. Furthermore, you can control your autopilot, switch between different instrument pages, and even create custom dashboards to display the information that is most important to you.

Base Station & Wireless Controller Installation Guide Base Station & Wireless Controller Installation Guide
Document number: 87042-2 Date: February 2005
Raymarine UK Ltd, Portsmouth, Hampshire, UK PO6 3TD +44 (0) 23 9269 3611
Raymarine Inc. Nashua, NH 03063-4219, USA Toll Free: 800-539-5539
+1 603-881-5200
Base Station & Wireless Controller Installation Guide
Self-tapping
screws
Base Station
Pozidriv screwdriver
Power Drill
Parts supplied
Tools Required
7
/
64
inch (2.7 mm) drill
1
/
8
inch (3.4 mm) drill
S100 REMOTE
MODE
STANDBY
PILOT
S100 Remote Smart Controller
Belt clip assembly
Lanyard
OR
Cradles x2
Cradles x2
3 Way
Connector
Block
SeaTalk Cable
Charging Cable
Ferrite
AAA batteries x2
STANDBY
PILOT
MODE
D7682-1
No. 6 size
No. 8 size
Min 3ft 3in (1m)
Locating Base Station
D7678-1
Fit as high up as possible, in a dry location
1.
3.
2.
1.
2.
D7675-1
3.
4.
Mark holes for the fixing screws.
Drill three
1
/
8
inch (3.4 mm) pilot holes
for the fixing screws
Fitting remote
Cradle at fixed position
Cradle on belt clip
Countersink the pilot holes to prevent
damage to the mounting surface.
To separate cradle from clip
C
l
i
c
k
Use the three No. 8 screws to secure
the cradle to the mounting surface
Base Station & Wireless Controller Installation Guide Base Station & Wireless Controller Installation Guide
2.
1.
3.
4.
Mark holes for the fixing screws.
Drill two
7
/
64
inch (2.7 mm) pilot
holes for the fixing screws
Countersink the pilot holes to prevent
damage to the mounting surface
Remove cover
6.
Replace cover
5.
Use the two No. 6 screws to secure the
Base Station to the mounting surface
Fitting Base Station
D7676-1
1
2
Connecting Base Station
Base Station
Connect to
Raymarine
SeaTalk
system
SeaTalk bus
SeaTalk bus
For example,
connect to an
unused SeaTalk
connector on an
instrument
Or use the SeaTalk
connector block
supplied to connect
to a SeaTalk bus
Connector block
If necessary, you can remove the SeaTalk connector from the Base Station cable,
to make direct connections to SeaTalk, e.g. at a Raymarine course computer.
Before connecting the Base Station, ensure that the 12 V supply on the asscociated SeaTalk
system is protected by a 5 A fuse.
SeaTalk color coding:
Note:
D7681-2
Important:
Yellow : SeaTalk data
Red: +12 V
Screen: 0 V
Fitting batteries to S100 Remote Connecting Smart Controller charging cable
Fit 2 x AAA batteries (supplied).
When replacing, use only
high-quality alkaline,
AAA size batteries.
Connect cable via 2 A fuse to 12 V supply
Clip ferrite onto cable, near to connector
D7504-1
+12 V
0 V
2 A fuse
Red
Black
Base Station & Wireless Controller Installation Guide Base Station & Wireless Controller Installation Guide
Document number: 87042-2 Date: February 2005
Raymarine UK Ltd, Portsmouth, Hampshire, UK PO6 3TD +44 (0) 23 9269 3611
Raymarine Inc. Nashua, NH 03063-4219, USA Toll Free: 800-539-5539
+1 603-881-5200
Base Station & Wireless Controller Installation Guide
Self-tapping
screws
Base Station
Pozidriv screwdriver
Power Drill
Parts supplied
Tools Required
7
/
64
inch (2.7 mm) drill
1
/
8
inch (3.4 mm) drill
S100 REMOTE
MODE
STANDBY
PILOT
S100 Remote Smart Controller
Belt clip assembly
Lanyard
OR
Cradles x2
Cradles x2
3 Way
Connector
Block
SeaTalk Cable
Charging Cable
Ferrite
AAA batteries x2
STANDBY
PILOT
MODE
D7682-1
No. 6 size
No. 8 size
Min 3ft 3in (1m)
Locating Base Station
D7678-1
Fit as high up as possible, in a dry location
1.
3.
2.
1.
2.
D7675-1
3.
4.
Mark holes for the fixing screws.
Drill three
1
/
8
inch (3.4 mm) pilot holes
for the fixing screws
Fitting remote
Cradle at fixed position
Cradle on belt clip
Countersink the pilot holes to prevent
damage to the mounting surface.
To separate cradle from clip
C
l
i
c
k
Use the three No. 8 screws to secure
the cradle to the mounting surface
  • Page 1 1
  • Page 2 2
  • Page 3 3

Raymarine Base Station Installation guide

Type
Installation guide

Raymarine Base Station is a device that allows you to connect your Raymarine instruments and accessories to a wireless network, enabling you to monitor and control your marine electronics from anywhere on your boat. With the Base Station, you can access data from your instruments, such as depth, speed, wind, and GPS position, on your compatible smartphone or tablet using the Raymarine mobile app. Furthermore, you can control your autopilot, switch between different instrument pages, and even create custom dashboards to display the information that is most important to you.

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI