Kawasaki K57003-119A Assembly Instructions

Brand: Kawasaki

Model: K57003-119A

Type: Assembly Instructions

Kawasaki K57003-119A is a tank bag designed for use on the Vulcan S motorcycle models EN650A/B/C/D. It has a capacity of 2 kg (5 lbs) and is water-resistant, making it suitable for storing items that need to be protected from the elements. The bag comes with a clear protect film that can be applied to the fuel tank to help prevent scratches. It also has a rain cover that can be used to protect the bag and its contents in heavy rain.

Parts List:

Ref. # Qty

A01 1

A02 1

A03 1

A04 1

A05 1

A06 1

Parts Diagram:

Approx. Assembly

Time

30 Minutes

Rear Hook&Loop Strap

Adhesive Rubber Gasket

Front Clip Strap

Rain Cover (not shown)

Assembly Instructions

Improper installation of this accessory could result in an accident causing serious bodily injury or death.

To prevent an accident, be sure that this accessory is properly and securely installed on your vehicle. If

you cannot properly install this accessory yourself, have a professional installer, such as an authorized

Kawasaki dealer, install it for you.

Prior to each use, check to be sure the accessory is securely attached to the motorcycle and periodically

inspect the accessory for any required adjustment, wear, and damage.

Description

Model

Vulcan S

EN650A/B/C/D

Part Number

K57003-119A

Description

Tank Bag

Clear Protect Film

Tank Bag

A05

A04

A02

A01

A03

Installation Instructions:

1. Park the vehicle on level ground, set the parking brake, turn off the ignition switch.

2. Refer to Owner's Manual to remove the seat.

3. Remove the ignition switch ring and tank cover (four screws) by pulling upward.

• Do not load bag with more than 2 kg (5 lbs).

• Do not exceed the maximum vehicle load. Review your vehicle owner’s manual for information regarding proper

• Before riding, make sure the bag is securely attached and the lid is zipped closed.

NOTICE

• Do not store temperature or moisture sensitive devices in the tank bag or lid tray.

• Tank bag is only water-resistant; take care to protect cargo in rainy weather with Rain Cover (A06).

• Do not exceed 130 km/h (80 MPH) vehicle speed with rain cover installed.

• Carefully clean the fuel tank mounting surfaces and the underside of the tank bag before each ride.

• Kawasaki cannot be responsible for any damage to the fuel tank finish or devices stored in the tank bag.

• Do not store magnetic data devices in bottom of tank bag or allow such devices to come in contact with

magnets.

• Not recommended for fitment with Reduced Reach Handlebars (99994-0517).

5. Install the front clip strap (A03) to the tank cover as

shown and re-install onto the fuel tank with original four

screws.

4. Peel the backing from the adhesive rubber gasket

(A02) and affix to the front of the ignition switch bracket

as shown.

A03

A02

Ignition Switch

Page 2 of 3

9. Re-install the seat and tighten the screw snugly.

Please check / adjust all fasteners in regular intervals.

Check for proper attachment before each ride.

Care and Cleaning:

Clean the tank bag with mild soap and warm water. Do not use harsh abrasive cleaners. Cover the clear tray

window when parked to minimize UV damage.

6. Thread the small end of the rear hook&loop strap

(A04) under the seat bracket and secure as shown.

NOTE: For fueling, unclip the front straps and lift the

tank bag clear of the fuel tank, then repeat Step 8 to

re-install the bag.

8. Position the tank bag (A01) over the fuel tank and

fasten the two front clips, then pull the bag rearward

and down to set. Front clip straps should be snug but

not tight.

7. Clean the fuel tank per Owner's Manual and apply

the clear protect film (A05) as desired after peeling the

backing off.

A04

A01

Page 3 of 3

Kawasaki K57003-119A Assembly Instructions

Kawasaki K57003-119A Assembly Instructions

Kawasaki K57003-119A Assembly Instructions

Related papers

Other documents