Aruba 580EX Series Hazardous Location Outdoor Access Points Installation guide

Brand: Aruba

Model: 580EX Series Hazardous Location Outdoor Access Points

Type: Installation guide

This manual is also suitable for

Aruba 580EX Series Hazardous Location

Outdoor Access Points

Installation Guide

Rev 01 | March 2022 1

The Aruba 580EX Series hazardous location outdoor access points (AP-585EX and AP-587EX) support the IEEE

802.11ax standard, delivering high performance with the MIMO (Multiple-Input, Multiple-Output) and OFDMA

(Orthogonal Frequency Division Multiple Access) technologies, while also supporting 802.11a/b/g/n/ac wireless

services.

Package Contents

580EX Series access point

Cable gland (Type: 20A2F) x 2

USB Type-C console cable x 1

Ground lug kit x 1

Tools Required

Phillips screwdriver (#2 for M4x6 screw)

Flat blade screwdriver (for Ethernet and AC port cap)

The weatherproof caps for Ethernet, AC and Console interfaces are connected to the access point, not loose in

the package.

Mounting kits for use with the 580EX Series access points are sold separately. Contact your Aruba sales

representative for details.

Inform your supplier if there are any incorrect, missing, or damaged parts. If possible, retain the carton,

including the original packing materials. Use these materials to repack and return the unit to the supplier if

needed.

2Aruba 580EX Series Hazardous Location Outdoor Access Points | Installation Guide

Hardware Overview

Figure 1 AP-585EX Front View

Figure 2 AP-585EX Rear View

E1/SFP+ E2/PSE E0/PoE+ Grounding Point

AC Power Port

USB Console Port,

Reset Button and

LED

Aruba 580EX Series Hazardous Location Outdoor Access Points | Installation Guide 3

Figure 3 AP-587EX Front View

Figure 4 AP-587EX Rear View

LED

The 580EX Series access point is equipped with one LED that indicates the system status of the access point.

E1/SFP+ E2/PSE E0/PoE+ Grounding Point

AC Power Port

USB Console Port,

Reset Button and

LED

4Aruba 580EX Series Hazardous Location Outdoor Access Points | Installation Guide

Table 1 580EX Series LED Meanings during Boot Up

1. Mostly off (off 6 seconds, then one blink flash)

2. Equally off/on (off 1 second, then red 1 second)

Table 2 580EX Series LED Meanings during Operation

Ethernet Ports

The 580EX Series access point is equipped with three Ethernet ports:

E0 PoE+ port: 100/1000/2500/5000Base-T auto-sensing MDI/MDI-X wired network port (RJ45). The E0 port

supports PoE-in, allowing the AP to draw power from an 802.3at/802.3bt PoE power source.

E1 SFP+ port: 10GBASE-R SFP+ port.

E2 PSE port: 100/1000Base-T auto-sensing MDI/MDI-X wired network port (RJ45). The AP supports 802.3af

PoE-Out when PoE powered, and supports up to 802.3at when powered by AC.

PoE input rating is 57V max|0.3A. 0.3A is per pair of wires in Ethernet cable. Ethernet cable has 4 pair of wires in

total.

AC Power Port

The 580EX Series access point is equipped with an AC power port. The 580EX Series access point does not ship

with any AC power cables. Aruba offers an AC power connector kit (sold separately) for customers to assemble

their own AC power cable.

Grounding Point

Always remember to protect the access point by installing the grounding line first before connecting to a

network and applying power. Additionally, if removing or taking down the AP, the grounding line should be the

last item disconnected.

LED Color/State Meaning

System LED Off No power to AP

Red Initial power-up

Flashing - Green AP booting, not ready

On - Green AP ready. GbE (or better) or SFP+ connected. The LED turns off

after 1200 seconds

Green - Yellow, 6 seconds

period AP ready. 100Mb connected. The LED turns off after 1200

seconds

Green - Flashing1AP in deep sleep

Red - Flashing2AP in thermal shutdown

LED Color/State Meaning

System LED Solid Red General fault - Immediate attention required

One red blink every 3

seconds Radio 0 fault (5 GHz)

Two quick red blinks 0.5

seconds apart cycled every

3 seconds

Radio 1 fault (2.4GHz)

To enable 802.3at support on E2, Intelligent Power and Temperature Monitoring (IPTM) must be enabled on

the AP to properly monitor and maintain safe operations of the AP under higher power draw requirements. If

IPTM is disabled, the maximum PoE support on E2 is 802.3af.

Aruba 580EX Series Hazardous Location Outdoor Access Points | Installation Guide 5

USB Type-C Console Port

Use the included USB Type-C console cable to connect the access point to a laptop or a serial terminal for direct

management.

Reset Button

The reset button can be used to reset the access point to factory default settings or turn off/on the LED display.

There are two ways to reset the access point to factory default settings:

Reset the AP during normal operation

Press and hold down the reset button using a small, narrow object such as a paper clip for more than 10

seconds during normal operation.

Reset the AP while powering up

1. Press and hold down the reset button using a small, narrow object such as a paper clip while the access point

is not powered on via PoE.

2. Connect the power supply (PoE) to the access point while the reset button is being held down.

3. Release the reset button on the access point after 15 seconds.

To turn off/on the LED display, press and release the reset button using a small, narrow object, such as a

paperclip for less than 10 seconds during normal operation of the access point.

Before You Begin

Refer to the sections below before beginning the installation process.

Pre-Installation Checklist

Before installing your access point, be sure that you have the following:

Cat5E or better shielded cable with network access

A compatible PoE injector with power cord

One of the following network services:

Aruba Discovery Protocol (ADP)

DNS server with an “A” record

DHCP Server with vendor specific options

FCC Statement: Improper termination of access points installed in the United States configured to non-US

model controllers will be in violation of the FCC grant of equipment authorization. Any such willful or

intentional violation may result in a requirement by the FCC for immediate termination of operation and may

be subject to forfeiture (47 CFR 1.80).

Aruba, in compliance with governmental requirements, has designed the 580EX Series access points so that

only authorized network administrators can change configuration settings. For more information about AP

configuration, refer to the AP Software Quick Start Guide.

Access points are radio transmission devices and as such are subject to governmental regulation. Network

administrators responsible for the configuration and operation of access points must comply with local

broadcast regulations. Specifically, access points must use channel assignments appropriate to the location in

which the access point will be used.

6Aruba 580EX Series Hazardous Location Outdoor Access Points | Installation Guide

Outdoor Planning and Deployment Considerations

Prior to deploying an outdoor wireless network, the environment must be evaluated to plan for a successful

WLAN deployment. Successfully evaluating the environment enables the proper selection of access points and

antennas and assists in the determination of their placement for optimal RF coverage. This process is considered

WLAN or RF planning and Aruba’s system engineers can assist in the outdoor planning process.

Identifying Specific Installation Locations

Use the access point placement map generated by the Aruba RF Plan software application to determine the

proper installation location(s). Each location should be as close as possible to the center of the intended

coverage area and should be free from obstructions or obvious sources of interference. These RF absorbers/

reflectors/interference sources will impact RF propagation and should be accounted for during the planning

phase and adjusted for in the RF plan.

Identifying Known RF Absorbers/Reflectors/Interference Sources

Identifying known RF absorbers, reflectors, and interference sources while in the field during the installation

phase is critical. Make sure that these sources are taken into consideration when you attach an access point to its

fixed location.

RF absorbers include:

Cement/concrete—Old concrete has high levels of water dissipation, which dries out the concrete, allowing

for potential RF propagation. New concrete has high levels of water concentration in the concrete, blocking

RF signals.

Natural Items—Fish tanks, water fountains, ponds, and trees

Brick

RF reflectors include:

Metal Objects—Metal pans between floors, rebar, fire doors, air conditioning/heating ducts, mesh windows,

blinds, chain link fences (depending on aperture size), refrigerators, racks, shelves, and filing cabinets.

Do not place an access point between two air conditioning/heating ducts. Make sure that access points are

placed below ducts to avoid RF disturbances.

RF interference sources include:

Other Wi-Fi networks

Microwave ovens

Bluetooth devices

Access Point Installation

The rules for the 5600-5650 MHz band vary by region.

Use of this equipment in near proximity, either horizontally or vertically, with other equipment should be

avoided because it could result in improper operation. If such use is necessary, this equipment and the other

equipment should be observed to verify that they are operating normally.

Service to all Aruba products should be performed by trained service personnel only.

Metal cover of enclosure is intended for installation in restricted access location.

Aruba 580EX Series Hazardous Location Outdoor Access Points | Installation Guide 7

Using Mount Kits

The 580EX Series access point can be installed on a wall or attached to a pole by using mount kits:

Grounding the Access Point

Grounding the access point must be completed before powering up the device. The ground wire should be #8

AWG.

1. Strip the insulating jacket off of one end of the ground wire and place the bare conductor into the ground lug

(included in the package), then crimp the connection by pressing firmly with the crimping pliers.

2. Fasten the ground lug to the grounding point on the access point with the screw included in the package.

Connecting the Ethernet Cable

To connect the Ethernet cable to the access point, perform the following steps using the cable glands that ship

with your access point.

Table 3 Applicable Mount Kits for 580EX Series Access Point

Part Number Description Supported Model

R9H97A AP-OUT-MNT-V1A Aruba Outdoor AP Pole/

Wall Long Mount Kit. AP-585EX: Wall or Pole

JW054A AP-270-MNT-H1 Aruba Outdoor AP

Hanging or Tilt Install Mount Kit. AP-587EX: Wall or Pole

AP-585EX: Flat or Sloped Ceiling

JW055A AP-270-MNT-H2 Aruba Outdoor AP Access

Flush Wall or Ceiling Mount. AP-587EX: Wall

AP-585EX: Flat Ceiling

R6W11A AP-270-MNT-H3 Aruba Outdoor AP

Hanging or Dual-Tilt Install Mount Kit. AP-587EX: Wall or Pole

AP-585EX: Flat or Sloped Ceiling

The 580EX Series access point does not ship with any mount kits. These mount kits are available as accessories

and must be ordered separately.

For installation instructions on mount kits, please refer to their respective installation guides found on the

Aruba support site https://asp.arubanetworks.com.

This 580EX Series access point is intended for installation in a RESTRICTED ACCESS LOCATION attached to a

pole or installed on a wall. Installers should disconnect power before working with or near the access point.

To prevent dropping and damage to the 580EX Series access point or to appendages of the handlers, extra

care should be taken when handling the access point.

Failure to use the included cable glands can lead to connectivity and PoE issues.

The cable is not included and must be purchased separately. Purchase a suitable UV-resistant, outdoor rated,

CAT 5E or better shielded cable for use with the access point.

8Aruba 580EX Series Hazardous Location Outdoor Access Points | Installation Guide

Figure 5 Ethernet Cable and 20A2F Cable Gland Assembly

1. Remove the dust cap from the Ethernet port

2. Slide the sealing nut, seal A, seal B, gland body and O-ring over the cable.

3. Insert the RJ45 connector to the Ethernet port.

4. Place the O-ring on the gland body, and ensure it is in place.

5. Thread the gland body into the Ethernet port and tighten to a torque of 70.5 in/lbs (8 Nm).

6. Push the seal B and seal A into the gland body and tighten the sealing nut onto the gland body to a torque of

53 in/lbs (6 Nm).

Figure 6 Ethernet Cable and 20A2F Cable Gland Installed to AP

Connecting the Fiber-optic Cable

Aruba provides a CKIT-EX-OD-SFP SFP gland kit (sold separately) to connect the fiber-optic cable to the AP. Refer

to the 580EX Series ordering guide on the Aruba website https://www.arubanetworks.com. The CKIT-EX-OD-SFP

SFP gland kit includes a SFP extension tube and a 20A2F gland, as shown in Figure 7.

Ethernet Cable

O-ring

Gland Body

Seal B

Seal A Sealing Nut

The fiber-optic cable is not included in the package and must be purchased separately. Purchase a suitable 6-

12 mm diameter, UV-resistant, outdoor rated cable for use with the access point.

Aruba 580EX Series Hazardous Location Outdoor Access Points | Installation Guide 9

Figure 7 Fiber-optic Cable and CKIT-EX-OD-SFP SFP Gland Kit

To connect the fiber-optic cable to the access point, perform the following steps.

1. Remove the dust cap from the E1 SFP+ port.

2. Insert the transceiver module into the SFP+ port, and ensure it is in place.

3. Slide the sealing nut, seal A, seal B, gland body, O-ring and SFP extension tube over the fiber-optic cable.

4. Insert the connector of the fiber-optic cable into the transceiver module, and ensure the connector is firmly

in place.

5. Screw the SFP extension tube into the E1 SFP+ port and tighten to a torque of 88 in/lbs (10 Nm).

6. Place the O-ring on the gland body, and ensure it is in place.

7. Thread the gland body into the SFP extension tube and tighten to a torque of 70.5 in/lbs (8 Nm).

8. Push the seal B and seal A into the gland body and tighten the sealing nut onto the gland body to a torque of

53in/lbs (6 Nm).

Fiber-optic Cable

O-ring Gland Body

Seal B

Seal A Sealing Nut

SFP Extension Tube

For more details on the 20A2F cable gland such as conditions of use, installation instructions and technical

data, please refer to CMP website:

https://www.cmp-products.com/Installation%20Instructions/CMP%20A2F.pdf

10 Aruba 580EX Series Hazardous Location Outdoor Access Points | Installation Guide

Figure 8 Fiber-optic Cable and CKIT-EX-OD-SFP SFP Gland Kit Installed to AP

Connecting the AC Power Cable

Best Practice for Outdoor Connection to AC Mains

In all circumstances and with any outdoor infrastructure the recommended practice is to connect to AC mains in

an outdoor grade weather protected junction box. This needs to be implemented by a qualified resource in a

manner that is consistent with the electrical code in force in the jurisdiction of deployment. In many countries

this will require a licensed electrician to perform this operation. In Japan, this would be performed by a Certified

Electrician by Ministry of Economy, Trade and Industry.

The use of plugs with infrastructure equipment is suitable only for temporary installs where nuisance tripping of

GFI plugs is considered tolerable. if a plug is desired for attachment to the cable assemblies then the installer is

expected to follow all directions provided with the plug end in a fashion consistent with local electrical code.

The 580EX Series access point does not ship with any AC power cables. Aruba offers an AP-AC-MLX-EX outdoor

Molex AC connector kit (sold separately) for customers to assemble their own AC power cable and connect the

AC power cable to the AP. For installation instructions, refer to the AP-AC-MLX-EX AC Connector Kit Installation

Guide shipped with the AP-AC-MLX-EX kit.

Software

For instructions on choosing operating modes and initial software configuration, refer to the AP Software Quick

Start Guide.

Verifying Post-Installation Connectivity

The integrated LEDs on the access point can be used to verify that the access point is receiving power and

initializing successfully (see Table 1 and Table 2). Refer to the AP Software Quick Start Guide for further details

Aruba access points are classified as radio transmission devices, and are subject to government regulations of

the host country. The network administrator(s) is/are responsible for ensuring that configuration and operation

of this equipment is in compliance with their country’s regulations. For a complete list of approved channels in

your country, refer to the Aruba Downloadable Regulatory Table at https://www.arubanetworks.com/techdocs/DRT/

Default.htm

Aruba 580EX Series Hazardous Location Outdoor Access Points | Installation Guide 11

on verifying post-installation network connectivity.

Electrical and Environmental Specifications

Electrical

Ethernet

E0 PoE+ port: 100/1000/2500/5000Base-T auto-sensing MDI/MDI-X wired network port (RJ45). The E0 port

supports PoE-in, allowing the AP to draw power from an 802.3at/802.3bt PoE power source.

E1 SFP+ port: 10GBASE-R SFP+ port.

E2 PSE port: 100/1000Base-T auto-sensing MDI/MDI-X wired network port (RJ45). The AP supports 802.3af

PoE-Out when PoE powered, and supports up to 802.3at when powered by AC.

Power over Ethernet (PoE): 57V max, 0.3A

Power

AC input: 100-240V, 50-60Hz, 1.4A

Environmental

Operating

Temperature: -40ºC to 65ºC (-40ºF to 149ºF)

Storage

Temperature: -40ºC to 70ºC (-40ºF to 158ºF)

Humidity: 5% to 93% non-condensing

For additional specifications on this product, please refer to the data sheet at www.arubanetworks.com.

Regulatory Model Number

For the purpose of regulatory compliance certifications and identification, this product has been assigned a

unique regulatory model number (RMN). The regulatory model number can be found on the product nameplate

label, along with all required approval markings and information. When requesting compliance information for

this product, always refer to this regulatory model number. The regulatory model number RMN is not the

marketing name or model number of the product.

The following regulatory model numbers apply to the 580EX Series:

AP-585EX RMN: APEX0585

AP-587EX RMN: APEX0587

Safety and Regulatory Compliance

If the 580EX Series access point is deployed supporting Fiber, PSE, and high user loads in extremely hot

temperatures or in hot environments with large solar loading environments, it is strongly recommended to

enable Intelligent Power and Temperature Monitoring (IPTM) to ensure continuous uninterrupted operations,

allowing the AP to disable specific and user-definable features to ensure continuity and prevent a thermal

shutdown of the AP.

RF Radiation Exposure Statement: This equipment complies with RF radiation exposure limits. This

equipment should be installed and operated with a minimum distance of 9.84 inches (25cm) between the

radiator and your body for 2.4 GHz and 5 GHz operations. This transmitter must not be co-located or operating

in conjunction with any other antenna or transmitter.

12 Aruba 580EX Series Hazardous Location Outdoor Access Points | Installation Guide

United States

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part

15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a

residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not

installed and used in accordance with the manufacturer’s instructions, may cause harmful interference to radio

communications. However, there is no guarantee that interference will not occur in a particular installation. If

this equipment does cause harmful interference to radio or television reception, which can be determined by

turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the

following measures:

Reorient or relocate the receiving antenna.

Increase the separation between the equipment and receiver.

Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.

Consult the dealer or an experienced radio or TV technician for help.

Improper termination of access points installed in the United States configured to a non-US model controller is a

violation of the FCC grant of equipment authorization. Any such willful or intentional violation may result in a

requirement by the FCC for immediate termination of operation and may be subject to forfeiture (47 CFR 1.80).

Innovation, Science and Economic Development Canada

This Class B digital apparatus meets all of the requirements of the Canadian Interference-Causing Equipment

Regulations.

In accordance with Innovation, Science and Economic Development Canada regulations, this radio transmitter

and receiver may only be used with an antenna, the maximum type and gain of which must be approved by

Innovation, Science and Economic Development Canada. To reduce potential radio interference, the type of

antenna and its gain shall be chosen so that the equivalent isotropic radiated power (EIRP) does not exceed the

values necessary for effective communication.

This device complies with Innovation, Science and Economic Development Canada's license-exempt RSS

regulations. Operation of this device is subject to the following two conditions: (1) this device may not cause

interference, and (2) this device must accept any interference, including interference that may cause undesired

operation.

When operated in 5.15 to 5.25 GHz frequency range, this device is restricted to indoor use to reduce the

potential for harmful interference with co-channel Mobile Satellite Systems.

Innovation, Sciences et Développement économique Canada

Cet appareil contient un ou plusieurs transmetteurs/récepteurs exempts de licence conformes aux RSS exempts

de licence d’Innovation, Sciences et Développement économique Canada. L’utilisation de ce périphérique est

soumise aux deux conditions suivantes: (1) Cet appareil ne doit pas produire d’interférences. (2) Cet appareil doit

accepter toutes les interférences, y compris les interférences pouvant engendrer un fonctionnement indésirable

Déclaration de la concernant l’exposition aux rayonnements à fréquence radioélectrique (FR): Cet

appareil est conforme aux limites d’exposition aux rayonnements FR établies par la FCC. Il doit être installé et

utilisé à une distance minimale de 25 cm (9,84 pouces) entre le radiateur et votre corps, qu’il opère sur la

bande 2,4 GHz ou 5 GHz. Cet émetteur ne doit pas être installé ou utilisé à proximité immédiate d’une autre

antenne ni d’un autre transmetteur.

The device could automatically discontinue transmission in case of absence of information to transmit, or

operational failure. Note that this is not intended to prohibit transmission of control or signaling information

or the use of repetitive codes where required by the technology.

Changes or modifications to this unit not expressly approved by the party responsible for compliance could

void the user’s authority to operate this equipment.

Toute modification effectuée sur cet équipement sans l'autorisation expresse de la partie responsable de la

conformité est susceptible d'annuler son droit d'utilisation.

Aruba 580EX Series Hazardous Location Outdoor Access Points | Installation Guide 13

de l’appareil.

En cas d'utilisation dans la plage de fréquences de 5,15 à 5,25 GHz, cet appareil doit uniquement être utilisé en

intérieur afin de réduire les risques d'interférence avec les systèmes satellites mobiles partageant le même

canal.

European Union Regulatory Conformance

The Declaration of Conformity made under Radio Equipment Directive 2014/53/EU is available for viewing at:

www.hpe.com/eu/certificates. Select the document that corresponds to your device’s model number as it is

indicated on the product label.

Wireless Channel Restrictions

5150-5350MHz band is limited to indoor only in the following countries; Austria (AT), Belgium (BE), Bulgaria (BG),

Croatia (HR), Cyprus (CY), Czech Republic (CZ), Denmark (DK), Estonia (EE), Finland (FI), France (FR), Germany (DE),

Greece (GR), Hungary (HU), Iceland (IS), Ireland (IE), Italy (IT), Latvia (LV), Liechtenstein (LI), Lithuania (LT),

Luxembourg (LU), Malta (MT), Netherlands (NL), Norway (NO), Poland (PL), Portugal (PT), Romania (RO), Slovakia

(SK), Slovenia (SL), Spain (ES), Sweden (SE), Switzerland (CH), Turkey (TR), United Kingdom (UK(NI)).

Medical

1. Equipment not suitable for use in the presence of flammable mixtures.

2. Connect to only IEC 60950-1 or IEC 60601-1 certified products and power sources. The end user is

responsible for the resulting medical system complies with the requirements of IEC 60601-1.

3. Wipe with a dry cloth, no additional maintenance required.

4. No serviceable parts, the unit must be sent back to the manufacturer for repair.

5. No modifications are allowed without Aruba approval.

Taiwan

第十二條

經型式認證合格之低功率射頻電機，非經許可，公司，商號或使用者均不得擅自變更頻率、加大功率或變更原設計之特性及功能。

第十四條

低功率射頻電機之使用不得影響飛航安全及干擾合法通信；經發現有干擾現象時，應立即停用，並改善至無干擾時方得繼續使用。

前項合法通信，指依電信法規定作業之無線電通信。低功率射頻電機須忍受合法通信或工業、科學及醫療用電波輻射性電機設備之干

擾。

1. 應避免影響附近雷達系統之操作。

2. 高增益指向性天線只得應用於固定式點對點系統。

3. 電波功率密度 MPE 標準值：1 mW/cm2，送測產品實測值： 0.9638 mW/cm2，建議使用時設備天線至少距離人體 25cm。

Brazil

Este equipamento não tem direito à proteção contra interferência prejudicial e não pode causar interferência

em sistemas devidamente autorizados.

Radio Frequency Range MHz Max EIRP

BLE/Zigbee 2402-2480 10 dBm

Wi-Fi

2412-2472 20 dBm

5150-5250 23 dBm

5250-5350 23 dBm

5470-5725 30 dBm

5725-5850 14 dBm

Lower power radio LAN product operating in 2.4 GHz and 5 GHz bands. Please refer to the ArubaOS User Guide/

Instant User Guide for details on restrictions.

14 Aruba 580EX Series Hazardous Location Outdoor Access Points | Installation Guide

Japan

México

La operación de este equipo está sujeta a las siguientes dos condiciones: (1) es posible que este equipo o

dispositivo no cause interferencia perjudicial y (2) este equipo o dispositivo debeaceptar cualquier interferencia,

incluyendo la que pueda causar su operación no deseada.

Este equipo ha sido diseñado para operar con las antenas que enseguida se enlistan:

https://www.arubanetworks.com/assets/og/OG_AP-580Series.pdf y para una ganancia máxima de antena de 14

dBi.

El uso con este equipo de antenas no incluidas en esta lista o que tengan una ganancia mayor que 14 dBi

quedan prohibidas. La impedancia requerida de la antena es de 50 ohms.

Нормативные требования Евразийского Экономического Союза

HPE Russia: ООО "Хьюлетт Паккард Энтерпрайз" Российская Федерация, 125171, г.

Москва, Ленинградское шоссе, 16А, стр.3, Телефон: +7 499 403 4248 Факс: +7 499 403

4677

'HPE Kazakhstan': TOO «Хьюлетт-Паккард (К)», Республика Казахстан, 050040, г.

Алматы, Бостандыкский район, проспект Аль-Фараби, 77/7, Телефон/факс: + 7 727

355 35 50

Kazakhstan

ЖШС "Хьюлетт Паккард Энтерпрайз" Ресей Федерациясы, 125171, Мәскеу, Ленинград тас жолы, 16A блок

3, Телефон: +7 499 403 4248 Факс: +7 499 403 4677

ЖШС «Хьюлетт-Паккард (К)», Қазақстан Республикасы, 050040, Алматы к., Бостандык ауданы, Әл-Фараби

даңғ ылы, 77/7, Телефон/факс: +7 (727) 355 35 50

Ukraine

Hereby, Hewlett Packard Enterprise Company declares that the radio equipment type [The Regulatory Model

Number [RMN] for this device can be found in the Regulatory Model Number section of this document] is in

compliance with Ukrainian Technical Regulation on Radio Equipment, approved by resolution of the CABINET OF

MINISTERS OF UKRAINE dated May 24, 2017, No. 355. The full text of the UA declaration of conformity is

available at the following internet address: https://certificates.ext.hpe.com/public/certificates.html

Х’ЮЛЕТТ ПАКАРД ЕНТЕРПРАЗ, 6280 АМЕРИКА ЦЕНТР Д-Р, САН-ХОСЕ, КАЛІФОРНІЯ 95002, США

Special Requirement for Safe Use

WARNING – DO NOT OPEN WHEN AN EXPLOSIVE ATMOSPHERE IS PRESENT

The connections on this equipment are not intended to be connected or disconnected when an explosive

atmosphere is present.

Only EX-certified personnel are allowed for on-site installation and electrical connections of equipment.

Manual switch TPS3851H18EDRBR is protected by at least an IP66 enclosure, it is not allowed to operate the

switch in a hazardous area.

Required protection shall be applied to avoid the high risk of mechanical damage occurred by the final

installation.

The equipment must be installed and used in an area of at least pollution degree 2, as defined in IEC 60664-1.

Aruba 580EX Series Hazardous Location Outdoor Access Points | Installation Guide 15

Only ATEX/IECEx certified cable glands as specified in the instructions are to be installed and used on the

enclosure, and IEC/EN 60079-14 shall be observed when installing. Suitable type of protection cable gland to

be selected with spec: M20x1.5 with minimum IP66 rating. Unused cable entry ports to be blocked by Ex

plugs with minimum IP66 rating.

Earthing system shall be finished in accordance with user manual before use.

Damaged Protective Vents have to be replaced immediately.

Type-C USB port is not to be used in hazardous area.

Standard Compliance

EN IEC 60079-0:2018

EN IEC 60079-7:2015/A1:2018

IEC 60079-0:2017 Edition 7.0

IEC 60079-7:2015+A1:2017 Edition 5.1

CSA C22.2 No.213-17

UL 121201 Ninth Edition

ATEX Certificate Number and Marking

TÜV 21 ATEX 8711 X

IECEx Certificate Number and Marking

IECEx TUR 21.0041X

Ex ec IIC T4 Gc

cCSAus Ex Marking

Class I, Division 2, Groups A, B, C and D T4

The equipment is intended to use in outdoor and environmentally challenging locations such as oil rigs, mining

facilities, and industrial plants, networks need to be protected from extreme temperatures, flammable gases

or vapors, and dust concentrations.

The equipment to be used in Zone 2 or CID2 hazardous area only with gas group IIC or Groups A, B,C and D.

16 Aruba 580EX Series Hazardous Location Outdoor Access Points | Installation Guide

Contact Aruba

Open Source Code

This product includes code licensed under the GNU General PublicLicense, the GNU Lesser General Public License, and/or

certain other open source licenses.

A complete machine-readable copy of the source code corresponding to such code is available upon request. This offer is valid

to anyone in receipt of this information and shall expire three years following the date of the final distribution of this product

version by Hewlett Packard Enterprise Company.

To obtain such source code, send a check or money order in the amount of US $10.00 to:

Hewlett Packard Enterprise Company

Attn: General Counsel

6280 America Center Drive

San Jose, CA 94089

USA

Warranty

This hardware product is protected by an Aruba warranty. For more details, visit www.hpe.com/us/en/support.html

Main Site https://www.arubanetworks.com

Support Site https://asp.arubanetworks.com

Airheads Social Forums and Knowledge Base https://community.arubanetworks.com/

North America Telephone 1-800-943-4526

1-408-754-1200

International Telephone https://www.arubanetworks.com/support-services/contact-support/

Software Licensing Site https://www.hpe.com/networking/support

End-of-Life Information https://www.arubanetworks.com/support-services/end-of-life/

Security Incident Response Team (SIRT) https://www.arubanetworks.com/support-service/security-bulletins/

Email: [email protected]

Aruba 580EX Series Hazardous Location Outdoor Access Points Installation guide

Brand: Aruba

Model: 580EX Series Hazardous Location Outdoor Access Points

Type: Installation guide

This manual is also suitable for

Download PDF

report

Aruba 580EX Series Hazardous Location Outdoor Access Points Installation guide

This manual is also suitable for

Aruba 580EX Series Hazardous Location Outdoor Access Points Installation guide

Related papers

Other documents