2. Computers & electronics
  3. Networking
  4. Network switches
  5. AMG
  6. AMG350-4GAT-1G-P75-PD

AMG AMG350-4GAT-1G-P75-PD Installation guide

  • Hello! I've reviewed the Installation Manual for the AMG350-4GAT-1G-P75-PD PoE Powered Switch. This document contains information about the switch's interface connections, port speeds, PoE capabilities, installation, and LED indicators. This industrial switch has 4 PoE ports with a maximum 30W output per port, and it can be powered using a PoE source. I'm ready to assist you with any questions you might have about this device.
  • What is the maximum PoE output per port?
    How is the switch powered?
    What is the maximum PoE budget?
    What type of installation does the switch support?
www.amgsystems.com
AMG350
amgsystems.com
AMG Systems Ltd. 3 The Omega Centre, Stratton Business Park, Biggleswade, Bedfordshire, SG18 8QB, UK
T :: +44 (0) 1767 600 777 E :: sales@amgsystems.com
D33642-00
AMG350-4GAT-1G-P75-PDAMG350-4GAT-1G-P75-PD
Industrial PoE Powered SwitchIndustrial PoE Powered Switch
Installation Manual - HardwareInstallation Manual - Hardware
INTERFACE CONNECTIONS
① Insert the Cat5/6 cable into the
RJ45 port.
② Ports 1-4 support IEEE802.3at
PoE output (max 30W per port).
③ If a PD device is connected the
respective PoE LED will turn on.
PORT SPEEDS
Proud to be a British
Manufacturer
Example part code:
AMG350-4GAT-1G-P75-PD
Character RJ45 Port Speed
F10/100 Base-T(X)
G10/100/1000 Base-T(X)
POE CAPABILITIES
Example part code:
AMG350-4GAT-1G-P75-PD
Characters PoE Standard Supported
None Non-PoE Port
AT IEEE 802.3at 30W Port
BT IEEE 802.3bt 60/90W Port
Characters PoE Budget
P75 75W Max
Note: The maximum available PoE budget will be determined by the PSE
source device used less the power consumption of the switch itself (4W)
along with the distance of the switch from the PSE source (100m max).
IEEE 802.3at Models
Type 1 & 2 PoE support
Mode A PSE only
IEEE 802.3bt Models
Type 1, 2, 3 & 4 PoE
support. Mode A
and/or Mode B PSE
DIN RAIL MOUNT INSTALLATION
POWER
SURFACE MOUNT INSTALLATION
③ Fix the unit to the surface
using two appropriate screws
(screws not provided)
LED INDICATORS
① Remove the DIN rail clip
by unscrewing the two xing
screws as shown.
② Attach the included wall
mount brackets with the
provided 4 x M3 screws as
shown.
IP RATING
To maintain the units IP40 rating any
screw holes that are not used should still
have their screws installed as shown in
green above.
The unit is powered by any
IEEE802.3at or IEEE802.3bt PoE
source (PSE) connected to Port 5
as shown.
If the PSE source is IEEE802.3at
compliant then the yellow POE PD
BT led will not be illuminated
Model Type Power
PD Model 4W Max*
*Excludes PoE Load
LED Colour Description
POE PD BT
O No 802.3bt PSE Detected
Yellow 802.3bt PSE Detected
PWR O Unit Not Powered
Yellow Unit Powered
RJ45
LINK/ACT
O No Ethernet link connection
Green Ethernet link present (ashes
with data trac activity)
POE
O No PoE being supplied
Yellow PoE is being delivered on the
RJ45 port
EARTH PROTECTION
To provide correct protection from ESD
and Surge events ensure that the unit
is correctly earthed using the provided
earth connection point in accordance
with local electrical codes & standards.
(cable not provided)
If the PSE source is IEEE802.3bt
compliant then the yellow POE PD
BT led will be illuminated.
In all cases the PWR LED located
on Port 5 will be illuminated once
any PoE power is received and
the PoE negotiation has been
established.
/