YardLine OAKRIDGE 8 x 12 Assembly Manual

16562

STOP!

Call Us First!

DO NOT RETURN TO STORE.

For immediate help with assembly or product information

call our toll free number:

1-800-844-9273

or email:

customerservice@backyardproductsllc.com

Our staff is ready to provide assistance

April through October M-F 8:00 AM to 4:30 PM EST

Saturday 8:30 AM to 4:30 PM EST

November through March M - F 8:00 AM to 5:00 PM EST

(This page intentionally left blank.)

08-04-2017

KEEP THIS MANUAL FOR FUTURE REFERENCE

ACTUAL FLOOR SIZE IS 96 x 140-5/8" (243,8 x 357,2 cm)

16562

BEFORE YOU BEGIN

IMPORTANT!

READ INSTRUCTIONS THOROUGHLY PRIOR TO BEGINNING ASSEMBLY.

- CUSTOMER SERVICE -

Call: 1-800-844-9273 email: customerservice@backyardproductsllc.com

•BUILDINGRESTRICTIONSANDAPPROVALS

Be sure to check with local building department and homeowners association for specic restrictions and/ or requirements before building.

•ENGINEEREDDRAWINGS

Contact our Customer Service Team if engineered drawings are needed to pull local permits.

•SURFACEPREPARATION

To ensure proper assembly you must build your shed on a level surface. Recommended methods and materials to level your shed are

listed on page 7.

•CHECKALLPARTS

Inventory all parts listed on pages 4 - 6. Contact our Customer Service Team if any parts are missing or damaged.

•ADDITIONALMATERIALS

You will need additional materials to complete your shed. See page 3 for required and optional materials and quantities.

OAKRIDGE 8' x 12' (244 x 366 cm)

ASSEMBLY MANUAL

ABackyardProductsCompany

Window Location

Optional

2

TOOLS

Safety! Always use approved safety glasses during assembly.

OptionalRequired

HELPFUL REMINDER SYMBOLS

Look for these symbols for helpful reminders throughout this manual.

ORIENT LUMBER AND TRIM FOR BEST APPEARANCE

= Assistance Required; two or more people.

= Ensure squareness.

= Important required step or operation.

= Helpful assembly hint.

= Mark part with pencil.

= Beginning of steps for assembly or installation.

= You have nished the assembly or installation.

= Level

❑ Gloves

Framing lumber is graded for structural strength and not appearance. Exterior trim is graded for one good side.

Always install the material leaving the best edge and best surface visible. Please remember that these blemishes in no way

negatively affect the strength or integrity of our product. (See Fig. A, B, C.)

A

❑ Safety Glasses

❑ Tape Measure

❑ Paint Tools

❑ Ladder

❑ Caulk Gun

❑ Hammer

❑ Level

FINISH

BEGIN

❑ Pencil

❑ Phillips

Screwdriver ❑ Tool Belt/

Nail Pouch

❑ Chalk Line

❑ Nail Gun

• gun nails

❑ Tin Snips

(for drip edge)

❑ Square or

❑ Utility Knife

❑ Shingle Blades

B C

❑ Drill / Driver

❑ 1/8" Drill Bit

❑ #2 Philips Drive Bit

❑ 1/4" Drill Bit

❑ 5/16" Drill Bit

❑ 1/2" Drill Bit

3

COMPLETING YOUR SHED

You will need these additional materials:

OPTIONAL MATERIALS

FOUNDATION OR FLOOR MATERIALS

ADDITIONAL MATERIALS

DRIPEDGE.....................60Feet #15ROOFINGFELT

To cover 148 Sq. Ft. of roof area.

1"GALVANIZEDROOFINGNAILS.........1/4Lb

For roong felt.

REFER TO THE BACK OF THIS MANUAL AND THE MANUFACTURER’S INSTRUCTIONS

FOR INSTALLATION OF SHINGLES, DRIP EDGE AND FELT.

3-TABSHINGLES............................7Bundles

PAINTFORSIDING..........................2Gallons

Use 100% acrylic latex exterior paint. (2) coats recommended.

CAULK.................................................3Tubes

Use acrylic latex exterior caulk that is paintable.

1"GALVANIZEDROOFINGNAILS....3Lbs

For shingles.

PAINTFORTRIM.............................1Quart

Use 100% acrylic latex exterior paint.

WOODGLUE.......................ExteriorRated

• This shed kit includes a complete wood oor system.

• This shed kit does not include ANY leveling materials.

• SeetheFLOORLEVELINGsectiononpage7forrecommendedmethodsandsuggestedmaterialstoproperlylevelyour

oor,asthiswillvarydependingonyourspecicsite.

WOODSIZECONVERSIONCHART

NominalBoardSize ActualSize

1" x 4".................3/4" x 3-1/2" (1,9 x 8,9 cm

)

2" x 4"..............1-1/2" x 3-1/2" (3,8 x 8,9 cm)

2" x 3"..............1-1/2" x 2-1/2" (3,8 x 6,3 cm

)

1" x 3".................3/4" x 2-1/2" (3,8 x 6,3 cm

)

19/32" x 3"......19/32" x 2-1/2" (1,5 x 6,3 cm)

PARTS IDENTIFICATION AND SIZES

RS RS

Part identication

letters are stamped on some parts.

Check these locations for

part stamp.

Treated lumber is stamped:

Alltreatedlumber

isstamped:

WALLS

x4 2 x 4 x 89" (5,1 x 10,2 x 226,1 cm)

SZ

x1 2 x 3 x 84" (5,1 x 7,6 x 213,4 cm)

FW

x4 2 x 4 x 68-5/8" (5,1 x 10,2 x 174,3 cm)

YF

x16 2 x 4 x 68" (5,1 x 10,3 x 172,7 cm)

UM

x2 2 x 4 x 48" (5,1 x 10,2 x 121,9 cm)

SP

x1 2 x 4 x 35-3/4" (5,1 x 10,2 x 90,8 cm)

RZ

x1 2 x 4 x 48" (5,1 x 10,2 x 121,9 cm)

SP

x1 2 x 4 x 34-1/4" (5,1 x 10,2 x 87,0 cm)

XY

PARTS LIST

INVENTORY YOUR PARTS before you begin.

We suggest sorting parts by the category they are listed in.

RAFTERS

x11 7-1/4 x 18-1/4" (18,4 x 46,4 cm)

TRIM

x8 3/8 x 1-3/4 x 67-3/4" (1 x 4,4 x 172,1 cm)

x2 3/8 x 2-3/4 x 80-1/4" (1 x 7 x 203,8 cm)

x2 3/8 x 2-3/4 x 69" (1 x 7 x 175,3 cm)

x12 2 x 4 x 68-7/16" (5,1 x 10,2 x 173,8 cm)

YJ

x2 2 x 4 x 69-7/8" (5,1 x 10,2 x 177,5 cm)

WW

x1 19/32 x 4 x 69-7/8" (1,5 x 10,2 x 177,5 cm)

WML

x1 19/32 x 4 x 69-7/8" (1,5 x 10,2 x 177,5 cm)

WMR

x2 2 x 4 x 16-1/2" (5,1 x 10,2 x 41,9 cm)

RD

x1 2 x 4 x 17-3/4" (5,1 x 10,2 x 45,1 cm)

CXA

x2 2 x 4 x 22-1/2" (5,1 x 10,2 x 57,2 cm)

AO

x1 2 x 4 x 10" (5,1 x 10,2 x 25,4 cm)

PWA

x2 2 x 3 x 11-7/8" (5,1 x 7,6 x 30,2 cm)

DQ

x1 2 x 4 x 13" (5,1 x 10,2 x 33,0 cm)

CWA

x1 2 x 4 x 4-5/8" (5,1 x 10,2 x 11,7 cm)

XTA

x2 3/8 x 2 x 5" (1,0 x 5,1 x 12,7 cm)

x1 19/32 x 3 x 30" (1,5 x 7,6 x 76,2 cm)

DLA

x6 19/32 x 3 x 30-1/8" (1,5 x 7,6 x 76,5 cm)

AZ x1 19/32 x 3 x 64-7/16" (1,5 x 7,6 x 163,7 cm)

DNA

x2 19/32 x 3 x 44-1/8" (1,5 x 7,6 x 112,1 cm)

DKA

x4 19/32 x 3 x 7-1/2" (1,5 x 7,6 x 19,1 cm)

CCR

x2 19/32 x 3 x 17" (1,5 x 7,6 x 43,1 cm)

EU

x2 19/32 x 3 x 11-1/2" (1,5 x 7,6 x 27,9 cm)

EFA

x4 2 x 4 x 72" (5,1 x 10,2 x 182,9 cm)

TM

3/4"

(1,9 cm)

1 x 3 x 5" (2,5 x 7,6 x 12,7 cm) Gauge Block for 3/4" (1,9 cm) measurement

x1 GAA

OSBORWOODGRAIN

x1 96" (243,8 cm) Z-STRIP

x1 19/32 x 3 x 28-1/2" (1,5 x 7,6 x 27,9 cm)

ROR

4

FLOOR

x2 2 x 4 x 48" (5,1 x 10,2 x 121,9 cm)

2 x 4 x 93" (5,1 x 10,2 x 236,2 cm)

x10

x2 2 x 4 x 92-5/8" (5,1 x 10,2 x 235,3 cm)

x2 1 x 2 x 96" (2,5 x 5,1 x 243,8 cm)

ZM

x4 2 x 3 x 68-7/16" (5,1 x 7,6 x 173,8 cm)

WE

x2 1 x 2 x 43-1/2" (2,5 x 5,1 x 110,5 cm)

WS

x4 19/32 x 3 x 23" (1,5 x 7,6 x 58,4 cm)

GI

x2 2 x 3 x 18-3/8" (5,1 x 7,6 x 50,2 cm)

WJ

OVERHANG

x2

x2 19/32 x 6-15/16 x 5-1/2" (1,5 x 17,6 x 13,4 cm)

SHELF

LOFT BENCH

SOFFIT

DOOR

UN

OO

x3

x2

2 x 4 x 94-1/2" (5,1 x 10,2 x 240 cm)

PARTS LIST continued...

x2

x4

x2

2 x 3 x 5-1/8" (5,1 x 7,6 x 13 cm)

2 x 3 x 7-7/8" (5,1 x 7,6 x 20 cm)

3/8 x 7-7/8 x 57-7/8" (1 x 20 x 147 cm)

3/8 x 5-3/16 x 69-3/8" (1 x 13,2 x 176,2 cm)

3/8 x 5-3/16 x 72" (1 x 13,2 x 182,9 cm)

3/8 x 7-7/8 x 7-7/8" (1 x 20 x 20 cm)

3/8 x 5-13/16 x 7-7/8" (1 x 14,8 x 20 cm)

WD

DY

PL

x1 2 x 3 x 93" (5,1 x 7,6 x 236,2 cm)

TP

x1 2 x 4 x 96" (5,1 x 10,2 x 243,8 cm)

1-1/4 x 2-1/2 x 69" (3,2 x 6,3 x 175,3 cm)

x1 7-1/4 x 18-1/4" (18,4 x 46,4 cm) WITHWOODGRAINONFACE

19/32 x 6-15/16 x 5-1/2" (1,5 x 17,6 x 13,4 cm)

5

PANEL PARTS LIST

ROOF PANELS

SHELF, LOFT &

BENCH

FLOOR

NOTE:Panelpartsarenotstamped.

Shelf/Loftpanelsare7/16"(1,1cm)thick.

Floorpanelsare5/8"(1,6cm)thick.

Roofpanelsare7/16"(1,1cm)thick.

7/16 x 11-7/8 x 88-7/8"

(1,1 x 30,2 x 226,1 cm)

7/16 x 23-7/8 x 88-7/8"

(1,1 x 60,6 x 226,1 cm)

7/16 x 35-7/8 x 82"

(1,1 x 91,1 x 231,1 cm)

x1

7/16 x 47-7/8 x 48"

(1,1 x 121,6 x 121,9 cm)

x2

7/16 x 22 x 46-1/2"

(1,1 x 55,9 x 118,1 cm)

x2

7/16 x 8-7/8 x 70"

(1,1 x 22,5 x 177,8 cm)

x2

7/16 x 22 x 96"

(1,1 x 55,9 x 243,8 cm)

x2

7/16 x 48 x 94-1/2"

(1,1 x 121,9 x 240 cm)

5/8 x 48 x 96"

(1,6 x 121,9 x 243,8 cm)

5/8 x 44-5/8 x 96"

(1,6 x 113,3 x 243,8 cm)

x2

x1

x2

3/8 x 44-5/8 x 72"

(1 x 113,3 x 182,9 cm)

x2

3/8 x 19-5/8 x 72"

(1 x 49,8 x 182,9 cm)

x6

3/8 x 48 x 72"

(1 x 121,9 x 182,9 cm)

WALL PANEL & DOORS PARTS LIST

x1

LEFTDOOR

x1

RIGHTDOOR

x3 BOXES

x6 BOXES

x275

x90

x14

x60

x7

x96

x64

x12

NAIL BOXES

VENT, DOOR HARDWARE, AND WINDOW

FASTENER/HARDWARE BAG

6

1-1/4" (3,2 cm)

2" (5,1 cm)

2-1/2" (6,4 cm)

3" (7,6 cm)

3/4" (1,9 cm)

2" (5,0 cm)

3" (7,6 cm)

2" (5,1 cm)

1-1/2" (3,8 cm)

x1

x2 x2

x8

x2

1/2" (1,3 cm)

8 x 16"

(20,3 x 35,6 cm)

3/4" (1,9 cm)

x12

1" (2,5 cm)

x4

x2

1-1/2" (3,8 cm)

x1 56" Metal Threshold

3/4" (1,9 cm) x18

Bagged seperately / special coating

x1

Large

Window Gable Window

Transom Window

7

D O O R

FLOOR LEVELING OPTIONS

There are multiple ways to level your oor frame. Our recommended leveling method is shown below.

Leveling materials are not included in this kit.

PREFERRED METHOD - 4x4 TREATED RUNNERS

Measurementsto

centersof4x4's.

• 3" Screws angled into 4x4.

• (2) at each point frame

• and 4x4 touch.

12"

(30,5 cm)

12"

(30,5 cm)

• Level under 4x4 runners only.

• Locate leveling material 12" from ends of runners and no more than 48" apart.

• Asphalt shingles should be used between 4x4 runners and blocks or treated lumber. Never use

shingles in direct contact with ground.

• For best results and aiding in water drainage use gravel under each concrete block.

LEVELINGMETHODS

• If you are building your shed on a concrete foundation see the following page.

CONCRETE

MATERIALREQUIRED

x2 4" x 4" x 12' (10 x 10 x 366 cm)Treated Lumber

FastenersforFrameto4"x4".

(3" Screws shown as one option.) Minimum (40) 3" screws / exterior grade.

Useonlywoodtreatedforgroundcontactandfastenersapprovedforusewithtreatedwood.

Alwayssupportframeseams.

Levelinghigherthan16"notrecommended.

LEVELINGMATERIALS

Gravel

2x4 Treated Lumber

Solid Masonry Blocks in 1", 2", 4" or 8" thickness

Asphalt Shingles

8" Block

4" Block

Gravel

Do not exceed 16".

4x4 Runner

Shingle

Maximum between leveling

material locations.

48"

12"

2x4 Treated Lumber

2" Block

Level

12"

8

CONCRETE FOUNDATION

Your kit contains all materials to construct a wooden oor. If you choose to install your kit

on a concrete slab refer to the diagram below.

• A treated 2 x 4" (5,1 x 10,2 cm) sill plate is required when installing your shed on concrete. Hint:Usetreatedlumberinyourkitor

purchasefulllengthtreatedlumber.

• Use a high quality exterior grade caulk beneath all sill plates.

• Fasten 2 x 4" (5,1 x 10,2 cm) sill plates to slab using approved concrete anchors (fastenersnotincluded).

• Check local code for concrete foundation requirements.

NOTES

Allow new concrete slabs to cure for at least seven (7) days.

2" x 4" x 11'-1-5/8" (5,1 x 10,2 x 339,4 cm)

2" x 4" x 8' (5,1 x 10,2 x 244 cm)

Caulk

Requires:

x2

x1

MUSTbetreatedlumber.

96"(243,8cm)

96"x140-5/8"(243,8x357,2cm) 133-5/8"(339,4cm)

8'x12'(243,8x365,8cm) 140-5/8"(357,2cm)

AActualSize B CBuildingSize

A

B

C

4"

(10,2 cm)

3-1/2"

(8,9 cm)

DOOR

TreatedSillPlate

Caulkbetweensill

plateandconcrete.

9

93"

(236,2 cm)

96"

(243,8 cm)

48"

(121,9 cm)

92-5/8

(235,3 cm)

Offset

Seam

Offset

Seam

140-5/8"

(357,2 cm)

124-5/8"

(316,6 cm)

92-5/8"

(243,8 cm)

108-5/8"

(275,9 cm)

48"

(121,9 cm)

64"

(121,9 cm)

80"

(203,2 cm)

32"

(81,3 cm) 16"

(40,7 cm)

16"

(40,7 cm)

16"

(40,7 cm)

16"

(40,7 cm)

12-5/8"

(32,1 cm)

48"

(121,9 cm)

3" (7,6 cm)

x2

x10

x44

2 x 4 x 92-5/8" (5,1 x 10,2 x 235,3 cm)

2 x 4 x 93" (5,1 x 10,2 x 236,2 cm)

x2 2 x 4 x 48" (5,1 x 10,2 x 121,9 cm)

PARTSREQUIRED:

Center

onmarks

Notethismeasurement

FLOORFRAME

Flush

Look for

Stamp

TREATED

HINT:

Foreasiernailing

standonframe.

2

1

Use two 3" nails at each mark.

Orient parts as shown on at surface. Measure and mark.

BEGIN

You have nished your oor frame.

Proceed to level and square frame.

FINISH

3

DOOR

10

DOOR

FINISH

5

LEVEL AND SQUARE FLOOR FRAME

Before attaching oor decking, it is important to level and square the oor frame.

A level and square oor frame is required to correctly construct your shed.

BEGIN

2

3

4

1

Use level and check the frame is level before applying oor panels.

Check for frame squareness by measuring diagonally across corners. If the measurements are the

same, the frame is square. The diagonal measurement will be approximately 170-1/4" (432,4 cm).

When the frame is level and square secure one side of frame to the 4x4 runners using one fastener at

ends of each runner. Move to the opposite end of the frame. Secure the frame to 4x4 runners with one

fastener at ends of each runner making sure the frame remains square (Fig.A).

Once the oor frame is level and square fasten the frame to the 4x4 runners at each point the frame

contacts the 4x4 runners.

See page 7 for the preferred oor leveling method.

First,secure

atendswith

onefastener.

Second,secure

atendswith

onefastener.

170-1/4"

(432,4 cm)

170-1/4"

(432,4 cm)

Fig.A

11

DOOR

48"

(121,9 cm)

140-5/8"

(352,2 cm)

6"

(15,2 cm)

Move to the opposite side. Using the long edge of the panel as a lever, move the

panel side-to-side until the top corner is ush to the oor frame (Fig.B).

Secure panel with two 2" nails in the corners.

2

BEGIN

1

3

4Continue attaching the panel using 2" nails 6" apart on edges and 12" apart inside panel.

Use a chalk line or use pre-painted grid lines to nail into joists under panel.

Ensureyouroorframeissquarebyinstallingonepanel

andsquaringframe.

Fig.A

Fig.B

Fig.C

Check the oor frame is square by measuring diagonally across the frame corners. If the measurements are the

same your oor frame is square. The measurement will be approximately 170-1/4" (432,4 cm) (Fig.C).

PARTSREQUIRED:

x1

x62

5/8 x 48 x 96"

(1,6 x 121,9 x 243,8 cm)

Gridlinesup

Seam

12"

(30,2 cm)

2" (5,1 cm)

Flush

(2)Nails

FLOOR PANELS

3/4"

(1,9 cm)

DOOR

170-1/4"

(432,4 cm

170-1/4"

(432,4 cm

Attach the 48 x 96" panel with the rough side up (painted-grid lines side) with the 48"

edge and corner ush to the oor frame (FigA). Secure panel with two 2" nails in the

corners.

12

6"

(15,2 cm)

12"

(30,5 cm)

48"

(121,9 cm)

44-5/8"

(113,3 cm)

140-5/8"

(357,2 cm)

32"

(81,3 cm)

12-5/8"

(32,1 cm)

PARTSREQUIRED:

FINISH

7You have nished attaching your oor panels.

Continue installing panels with rough side up (painted grid lines).

Position 44-5/8" panel in middle of oor frame.

Use grid lines on panel for 2" nails 6" apart on edges, and 12" apart inside panels.

5

7

6

x1 x1

x124

5/8 x 48 x 96"

(1,6 x 121,9 x 243,8 cm)

5/8 x 44-5/8 x 96"

(1,6 x 113,3 x 243,8 cm)

Gridlinesup

2" (5,1 cm)

FLOOR PANELS

Flush

DOOR

13

DOOR

Backwall

Frontwall

Leftwall

(Your window location

will be determined later

during assembly.)

RightWall

Checktheoorframeislevelafterinstallingoorpanels.

Re-levelifneeded.

HINT:

IMPORTANT!

•Theoorshouldbeusedasastableworksurfaceforwallconstruction.

• Organizeyourassemblyprocedureduringthebuildprocess

 toavoidover-handlingofthewalls.

LEFT WALL FRAME

PARTSREQUIRED:

140-5/8”

(352,7cm)

120”

(304,8 cm)

96”

(243,8 cm)

68-5/8”

(174,3 cm)

72”

(182,9 cm)

48”

(121,9 cm)

72”

(182,9 cm)

20-5/8”

(52,4 cm)

24”

(61 cm)

68”

(172,7 cm)

1-1/2”

(3,8 cm)

1-1/2”

(3,8 cm)

1-1/2”

(3,8 cm)

UMx7

TM

YF

TM

YF

HINT:

Foreasiernailing

standonframe.

x2 2 x 4 x 72" (5,1 x 10,2 x 182,9 cm)

TM

x2 2 x 4 x 68-5/8" (5,1 x 10,2 x 174,3 cm)

YF

x7 2 x 4 x 68" (5,1 x 10,2 x 172,7 cm)

UM

x32

14

DOOR

3" (7,6 cm)

BEGIN

1

Use two 3" nails at each mark and four 3" nails at seams

For left wall, orient parts on edge on oor. Measure and mark.

2

TOENAILING

YOUWILLASSEMBLEONELEFTANDONERIGHTWALLSEPARATELY.

YOUMUSTBUILDTHELEFTANDRIGHTSIDEWALLSEXACTLYASSHOWN!

IMPORTANT

MEASUREMENT

15

ForsquarenessmaintainFlushand3/4"

measurementalongpaneledges.

LEFT SIDE WALL PANELS

48 x 72"

(121,9 x 213,4 cm)

PARTSREQUIRED:

x1

x45 2" (5,1 cm)

Fig.B

BEGINHERE

Fig.A

3/4"

(1,9 cm) 3/4"

(1,9 cm)

2Nails

Flush

DOOR

48"

(121,9 cm)

3/4"

(1,9 cm) 1”

(2,5 cm)

3/4"

(1,9 cm)

12"

(30,5 cm) 6"

(15,2 cm)

20-5/8"

(52,4 cm)

Place 48x72" panel onto wall frame ush to top of frame with primed side up as shown.

Use the gauge block to mark the 3/4" measurement on the wall stud. Secure panel with

two 2" nails in the corners (Fig.A).

Nail the panel using 2" nails 6" apart on edges and 12" apart inside panel.

Ensureyourwallframeissquarebyinstallingonepanelandsquaringframe.

YOUWILLASSEMBLEONELEFTANDONERIGHTWALLSEPARATELY.

Move to the opposite end. Using the long edge of the panel as a lever move the panel side-to-side until you have

a 3/4" measurement on the wall stud. Secure corner with two 2" nails (Fig.B).

4

5

3

3/4"GAUGE

BLOCK

3/4"GAUGE

BLOCK

Primed

sideup

16

3/4"

(1,9 cm)

48"

(121,9 cm)

12"

(30,5 cm)

6"

(15,2 cm)

Flush

44-5/8"

(113,3 cm)

12"

(30,5 cm)

6"

(15,2 cm)

Flush

Forsquarenessmaintainushand

3/4"measurementalongpaneledges.

Forsquarenessmaintainush

alongpaneledges.

Place center 48"x72" panel on frame

as shown with primed side facing up.

Nail using 2" nails 6" apart on edges

and 12" apart inside panel.

6

Place end 44-5/8"x72"panel on frame

as shown with primed side facing up.

Nail using 2" nails 6" apart on edges

and 12" apart inside panel.

7

You have nished building your LEFT WALL.

FINISH

9

Primed

sideup

Primed

sideup

48 x 72"

(121,9 x 213,4 cm)

44-5/8 x 72"

(121,9 x 213,4 cm)

x1 x1

x90

LEFT SIDE WALL PANELS

PARTSREQUIRED: 2" (5,1 cm)

8Carefully ip the LEFT wall over.

DOORDOOR

3/4"GAUGE

BLOCK

3/4"GAUGE

BLOCK

17

DOOR

RIGHT WALL FRAME

PARTSREQUIRED:

140-5/8”

(352,7cm)

120”

(304,8 cm)

96”

(243,8 cm)

68-5/8”

(174,3 cm)

72”

(182,9 cm)

48”

(121,9 cm)

72”

(182,9 cm)

20-5/8”

(52,4 cm)

24”

(61 cm)

68”

(172,7 cm)

1-1/2”

(3,8 cm)

1-1/2”

(3,8 cm)

1-1/2”

(3,8 cm)

UMx7

TM YF

TM

YF

HINT:

Foreasiernailing

standonframe.

x2 2 x 4 x 72" (5,1 x 10,2 x 182,9 cm)

TM

x2 2 x 4 x 68-5/8" (5,1 x 10,2 x 174,3 cm)

YF

x7 2 x 4 x 68" (5,1 x 10,2 x 172,7 cm)

UM

x32 3" (7,6 cm)

BEGIN

1

Use two 3" nails at each mark and four 3" nails at seams

For right wall, orient parts on edge on oor. Measure and mark.

2

TOENAILING

IMPORTANT

MEASUREMENT

18

RIGHT SIDE WALL PANELS

48 x 72"

(121,9 x 213,4 cm)

PARTSREQUIRED:

x1

x45 2" (5,1 cm)

Fig.B

Fig.A

Flush

3/4"

(1,9 cm) 3/4"

(1,9 cm)

2Nails

DOOR

BEGINHERE

48"

(121,9 cm)

3/4"

(1,9 cm)

3/4"

(1,9 cm)

20-5/8"

(52,4 cm)

12"

(30,5 cm)

1”

(2,5 cm)

6"

(15,2 cm)

Nail the panel using 2" nails 6" apart on edges and 12" apart inside panel.

Ensureyourwallframeissquarebyinstallingonepanelandsquaringframe.

Move to the opposite end. Using the long edge of the panel as a lever move the panel side-to-side until you have

a 3/4" measurement on the wall stud. Secure corner with two 2" nails (Fig.B).

4

5

3

3/4"GAUGE

BLOCK

3/4"GAUGE

BLOCK

Primed

sideup

Forsquarenessmaintainushand

3/4"measurementalongpaneledges.

Place 48x72" panel onto wall frame ush to top of frame with primed side up as shown.

Use the gauge block to mark the 3/4" measurement on the wall stud. Secure panel with

two 2" nails in the corners (Fig.A).

Page is loading ...

YardLine OAKRIDGE 8 x 12 Assembly Manual

YardLine OAKRIDGE 8 x 12 Assembly Manual

Related papers

Other documents