Heartland PRESTWICK Assembly Manual

Brand: Heartland

Model: PRESTWICK

Type: Assembly Manual

This manual is also suitable for

Architectural Series

16660

STOP!

Call Us First!

DO NOT RETURN TO STORE.

For immediate help with assembly or product information

call our toll free number:

1-800-577-9663

or email:

customerservice@backyardproductsllc.com

Our staff is ready to provide assistance

April through October M-F 8:00 AM to 6:00 PM EST

Saturday 8:30 AM to 4:30 PM EST

November through March M - F 8:00 AM to 5:00 PM EST

(This page intentionally left blank.)

01/13/2016

KEEP THIS MANUAL FOR FUTURE REFERENCE

ASSEMBLY MANUAL

BEFORE YOU BEGIN

IMPORTANT!

READ INSTRUCTIONS THOROUGHLY PRIOR TO BEGINNING ASSEMBLY.

- CUSTOMER SERVICE -

Call: 1- 800-577-9663 email: customerservice@backyardproductsllc.com

ACTUAL FLOOR SIZE IS: 96" x 120" (243,8 x 304,8 cm)

PRESTWICK 8' x 10' (244 x 304,8 cm)

ARCHITECTURAL SERIES

16660

A Backyard Products Company

• BUILDING RESTRICTIONS AND APPROVALS

Be sure to check with local building department and homeowners association for speci c restrictions and/ or requirements before building.

• ENGINEERED DRAWINGS

Contact our Customer Service Team if engineered drawings are needed to pull local permits.

• SURFACE PREPARATION

To ensure proper assembly you must build your shed on a level surface. Recommended methods and materials to level your shed are

listed on page 8.

• CHECK ALL PARTS

Inventory all parts listed on pages 3 - 4. Contact our Customer Service Team if any parts are missing or damaged.

• ADDITIONAL MATERIALS

You will need additional materials to complete your shed. See page 5 for required and optional materials and quantities.

TOOLS

Safety! Always use approved safety glasses during assembly.

OptionalRequired

HELPFUL REMINDER SYMBOLS

Look for these symbols for helpful reminders throughout this manual.

ORIENT LUMBER AND TRIM FOR BEST APPEARANCE

= Assistance Required; two or more people.

= Ensure squareness.

= Important required step or operation.

= Helpful assembly hint.

= Mark part with pencil.

= Beginning of steps for assembly or installation.

= You have  nished the assembly or installation.

= Level

 Gloves

Framing lumber is graded for structural strength and not appearance. Exterior trim is graded for one good side.

Always install the material leaving the best edge and best surface visible. Please remember that these blemishes in no way

negatively affect the strength or integrity of our product. (See Fig. A, B, C.)

 Safety Glasses

 Tape Measure

 Paint Tools

 Ladder

 Wood Glue

 Caulk Gun

 Hammer

 Level

FINISH

BEGIN

 Pencil

 Phillips

Screwdriver

 Drill / Driver

 5/16" Drill Bit

 1/8" Drill Bit

 #2 Philips Drive Bit

 Tool Belt/

Nail Pouch

 Chalk Line

 Nail Gun

• gun nails

 Tin Snips

(for drip edge)

 Square

 Utility Knife

 Shingle Blades

B C

PLA

2 x 2 x 10-3/8" (5,1 x 5,1 x 26,4 cm)

PARTS LIST

INVENTORY YOUR PARTS before you begin.

We suggest sorting parts by the category they are listed in.

PARTS IDENTIFICATION AND SIZES

WOOD SIZE CONVERSION CHART

Nominal Board Size Actual Size

1" x 4".................3/4" x 3-1/2" (1,9 x 8,9 cm)

2" x 4"..............1-1/2" x 3-1/2" (3,8 x 8,9 cm)

2" x 3"..............1-1/2" x 2-1/2" (3,8 x 6,3 cm)

1" x 3".................3/4" x 2-1/2" (3,8 x 6,3 cm)

Part identication

letters are stamped on some parts.

Check these locations for

part stamp.

WALLS

RAFTERSDOOR

TRIM

1 x 3 x 5" (2,5 x 7,6 x 12,7 cm) Gauge Block for 3/4" (1,9 cm) measurement

GAA

3/4"

(1,9 cm)

2 x 4 x 17-1/2" (2,5 x 10,2 x 44,5 cm)

2 x 4 x 72" (5,1 x 10,2 x 182,9 cm)

x16

2 x 4 x 73-1/2" (5,1 x 10,2 x 186,7 cm)

THA

2 x 4 x 21" (5,1 x 10,2 x 53,3 cm)

SBA

3/8 x 4-3/4 x 61-1/2" (1 x 12,1 x 156,2 cm)

2 x 4 x 48" (5,1 x 10,2 x 122 cm)

2 x 4 x 56" (5,1 x 10,2 x 142,2 cm)

2 x 4 x 89" (5,1 x 10,2 x 226,1 cm)

2 x 3 x 22-1/2" (5,1 x 7,6 x 57,1 cm)

QHA

2 x 4 x 59-7/8" (5,1 x 10,2 x 152,1 cm)

3/8 x 2-1/2 x 61" (1 x 6,4 x 154,9 cm)

3/8 x 4-3/4 x 61" (1 x 12,1 x 154,9 cm)

FDA

19/32 x 2-1/2 x 55-1/8" (1,5 x 6,3 x 140 cm)

19/32 x 2-1/2 x 63" (1,5 x 6,4 x 160 cm)

1-1/4 x 2-1/2 x 69" (3,2 x 6,3 x 175,3 cm)

19/32 x 2-1/2 x 23" (1,5 x 6,3 x 58,4 cm)

6 x 24" (15,2 x 61 cm)

1 x 4 x 60" (2,5 x 10,2 x 152,4 cm)

x10

2 x 4 x 59-7/8" (5,1 x 10,2 x 152,1 cm)

QJA

GCA

1 x 3 x 9-1/2" (2,5 x 7,6 x 24,17 cm)

RCO

2 x 4 x 8-7/8" (5,1 x 10,2 x 22,5 cm)

PKA

2 x 2 x 12" (5,1 x 5,1 x 30,5 cm)

PRO

2 x 2 x 10-3/8" (5,1 x 5,1 x 26,4 cm)

NGO

1 x 3 x 11-7/8" (2,5 x 7,6 x 30,2 cm)

1 x 4 x 11-7/8" (2,5 x 10,2 x 30,2 cm)

PVA

2 x 4 x 5-7/8" (5,1 x 10,2 x 14,9 cm)

3/8 x 4-3/4 x 72" (1 x 12,1 x 182,9 cm)

3/8 x 2-13/16 x 73-7/8" (1 x 7,1 x 187,6 cm)

2 x 4 x 14" (5,1 x 10,2 x 35,6 cm)

LPA

3/8 x 5-7/8 x 47-7/8" (1 x 12,1 x 121,6 cm)

3/8 x 5-7/8 x 73-5/8" (1 x 14,9 x 187,6 cm)

BOXES

x305

x125

x12

x70

x96

x12

NAIL BOXES

FASTENER/HARDWARE BAG

DOOR & WINDOW HARDWARE / VENT

ROOF PANELS

NOTE: Panel parts are not stamped.

Roof panels are 7/16" (1,1 cm) thick.

7/16 x 11-7/8 x 48"

(1,1 x 30,2 x 121,9 cm)

7/16 x 11-7/8 x 84"

(1,1 x 30,2 x 213,4 cm)

7/16 x 36 x 48"

(1,1 x 91,4 x 121,9 cm)

7/16 x 48 x 96"

(1,1 x 121,9 x 243,8 cm)

1" (2,5 cm)

1/2" (1,3 cm)

2" (5,1 cm)

3" (7,6 cm)

3/4" (1,9 cm)

2" (5,0 cm)

3" (7,6 cm)

2" (5,1 cm)

1-1/2" (3,8 cm)

x42

1-5/8" (4,1 cm)

T-Handle

1-1/2" (3,8 cm)

(2 screws in each package)

Vent

56" Metal Threshold

3/4" (1,9 cm) x18

Bagged seperately / special coating

WALL PANELS, OVERHANG, SOFFIT & DOORS

3/8 x 48 x 76"

(1 x 121,9 x 193 cm)

3/8 x 48 x 76"

(1 x 121,9 x 193 cm)

3/8 x 48 x 76"

(1 x 121,9 x 193 cm)

3/8 x 23-7/8 x 76"

(1 x 60,6 x 193 cm)

LEFT DOOR

RIGHT DOOR

1" (2,5 cm)

(4 screws in each package)

Spring-Bolt

3/8 x 24-3/8 x 48"

(1 x 61,9 x 121,9 cm)

3/8 x 24-3/8 x 48"

(1 x 61,9 x 121,9 cm)

3/8 x 11-7/8 x 58-1/4"

(1 x 30,2 x 148 cm)

3/8 x 3-1/2 x 5-7/8"

(1 x 8,9 x 14,9 cm)

OPTIONAL MATERIALS

DRIP EDGE ..................... 43 Feet #15 ROOFING FELT

To cover 110 Sq. Ft. of roof area.

1" GALVANIZED ROOFING NAILS.........1/4 Lb

For roong felt.

REFER TO THE BACK OF THIS MANUAL AND THE MANUFACTURER’S INSTRUCTIONS

FOR INSTALLATION OF SHINGLES, DRIP EDGE AND FELT.

COMPLETING YOUR SHED

You will need these additional materials:

3-TAB SHINGLES ............................. 5 Bundles

PAINT FOR SIDING .......................... 2 Gallons

Use 100% acrylic latex exterior paint. (2) coats recommended.

CAULK ................................................. 2 Tubes

Use acrylic latex exterior caulk that is paintable.

1" GALVANIZED ROOFING NAILS.... 3 Lbs

For shingles.

PAINT FOR TRIM ........................... 2 Quarts

Use 100% acrylic latex exterior paint.

WOOD GLUE ....................... Exterior Rated

REINFORCED WOOD FLOOR FRAME (OPTIONAL)

x20

2 x 4 x 8' (5 x 10 x 244 cm) Treated Lumber

Cut to (3) 2 x 4 x 93" (5 x 10 x 236 cm)

ea. 3" (7,6 cm) Hot Dipped Galvanized Nails

Optional 12" (30,5 cm) spacing

Standard 16" (40,7 cm) spacing

IMPORTANT! Depending on your specic use you may want to construct a heavy duty oor frame by adding additional oor joists

(shown below as shaded). Below is a list of additional materials (not included):

FOUNDATION OR FLOOR MATERIALS

ADDITIONAL MATERIALS

• This shed does not include any oor or leveling materials. Use our optional oor kit with building instructions and nails included.

• See the FLOOR LEVELING section on page 8 for recommended methods and suggested materials to properly level your oor,

as this will vary depending on your specic site.

• If you choose to install your kit on a concrete slab refer to page 6.

• If you choose to build your own wood oor foundation refer to page 7.

CONCRETE FOUNDATION

If you choose to install your kit on a concrete slab refer to the diagram below.

(10,2 cm)

3-1/2"

(8,9 cm)

A B CActual Floor SizeBuilding Size

• A treated 2 x 4" (5,1 x 10,2 cm) sill plate is required when installing your shed on concrete.

• Use a high quality exterior grade caulk beneath all sill plates.

• Fasten 2 x 4" (5,1 x 10,2 cm) sill plates to slab using approved concrete anchors (fasteners not included).

• Check local code for concrete foundation requirements.

96" (243,8 cm)

113" (287 cm)

8' x 10' (235 x 304,8 cm)

8' x 10' (243,8 x 304,8 cm)

120" (304,8 cm)

Treated Sill Plate

Caulk between sill plate

and concrete.

2 x 4 x 8' (5,1 x 10,2 x 243,8 cm)

2 x 4 x 10' (5,1 x 10,2 x 305 cm)

Requires:

MUST be treated lumber.

Caulk

Allow new concrete slabs to cure for at least seven (7) days.

NOTES

ACTUAL FLOOR SIZE IS: 96" x 120" (243,8 x 304,8 cm)

BUILD YOUR OWN WOOD FLOOR OPTION

(Materials not included.)

2" x 4" x 10' (5,1 x 10,2 x 304,8 cm)

2" x 4" x 8' (5,1 x 10,2 x 243,8 cm)

MUST be treated lumber

5/8" x 48" x 96" (1,6 x 121,9 x 243,8 cm)

x28

1 lb. of 2" (5,1 cm) Hot Dipped Galvanized Box-Type Nails

40 Nails - 3" (7,6 cm) Hot Dipped Galvanized Box-Type Nails

MATERIAL REQUIRED

4" x 4" x 10' (10,2 x 10,2 x 304,8 cm)

Screws for Frame to 4"x 4"

Minimum 3" screws / exterior grade.

120"

(304,8 cm)

96"

(243,8 cm)

93"

(236,2 cm)

16"

(40,6 cm)

16"

(40,6 cm)

3" (7,6 cm)

2" (5,1 cm)

3" (7,6 cm)

Measurements to

centers of 4x4's.

• 3" Screw angled into 4x4.

• (2) at each point frame

and 4x4 touch.

4x4 Runners

(not included).

• Level under 4x4 runners only.

• Locate leveling material 12" from ends of runners and no more than 48" apart.

• Asphalt shingles should be used between 4x4 runners and blocks or treated lumber. Never use

shingles in direct contact with ground.

• For best results and aiding in water drainage use gravel under each concrete block.

LEVELING METHODS

• If you are building your shed on a concrete foundation see the following page.

CONCRETE

MATERIAL REQUIRED

4" x 4" x 10' (10,2 x 10,2 x 304,8 cm) Treated Lumber

Fasteners for Frame to 4"x 4".

(3" Screws shown as one option.) Minimum (24) 3" screws / exterior grade.

Use only wood treated for ground contact and fasteners approved for use with treated wood.

Always support frame seams.

Leveling higher than 16" not recommended.

LEVELING MATERIALS

Gravel

2x4 Treated Lumber

Solid Masonry Blocks in 1", 2", 4" or 8" thickness

Asphalt Shingles

4" Block

8" Block

Gravel

Do not exceed 16".

4x4 Runner

Shingle

Maximum between leveling

material locations.

48"

12"

2x4 Treated Lumber

2" Block

Level

12"

(30,5 cm)

12"

(30,5 cm)

96"

(243,8 cm)

Runners are generally 12"

(30,5 cm) from ends of oor

frame and under seams.

OPTIONAL WOOD FRAME FLOOR LEVELING OPTIONS

There are multiple ways to level your oor frame. Our recommended leveling method is shown below.

Leveling materials are not included in this kit.

PREFERRED METHOD - 4x4 TREATED RUNNERS (Typical for 8' x 10' Kit)

First, secure at ends

with one fastener.

Second, secure at ends

with one fastener.

150-15/16"

(383,4 cm)

150-15/16"

(383,4 cm)

Fig. A

LEVEL AND SQUARE FLOOR FRAME

Before attaching  oor decking, it is important to level and square the  oor frame.

A level and square  oor frame is required to correctly construct your shed.

FINISH

BEGIN

Use level and check the frame is level before applying  oor panels.

Check for frame squareness by measuring diagonally across corners. If the measurements are the

same, the frame is square. The diagonal measurement will be approximately 150-5/16" (383,4 cm).

When the frame is level and square secure one side of frame to the 4x4 runners using one fastener at

ends of each runner. At the opposite end of the frame, secure the frame to 4x4 runners with one fastener

at ends of each runner making sure the frame remains square (Fig. A).

Once the  oor frame is level and square fasten the frame at each point the frame contacts the 4x4

runners.

See page 8 for the preferred  oor leveling method.

IMPORTANT!

Check the oor frame is level after installing oor panels. Re-level if needed.

• The oor should be used as a stable work surface for wall construction.

• Organize your assembly procedure during the build process

to avoid over-handling of the walls.

HINT:

IMPORTANT!

DOOR

EAVE WALL

FRONT WALL

BACK WALL

DOOR

PARTS REQUIRED:

FINISH

You have  nished rafter jig. Proceed to assemble your rafters.

RAFTER ASSEMBLY

96"

(243,8 cm)

22-1/4"

(56,5 cm)

22-1/4"

(56,5 cm)

48-1/8"

(122,2 cm)

3/4"

(1,9 cm)

PVA x3

3" (7,6 cm)

PVA

2 x 4 x 5-7/8" (5,1 x 10,2 x 14,9 cm)

Measure over 48-1/8" and up 22-1/4" from the  oor edges and secure the third PWA using two 3" screws.

Check this PVA is 22-1/4" at both ends for squareness.

BEGIN

Secure one PVA  ush to the  oor deck using two 3" screws.

Measure over 96-3/4" and install a second PVA  ush to the  oor deck. PWA will overhang the  oor.

Secure using two 3" screws.

96-3/4"

(245,7 cm)

IMPORTANT MEASUREMENT !!

Fig. B

Fig. A

It is very important to assemble your rafters using the following method for an even and  at roof.

You will build a rafter jig using the  oor and three PVA parts as shown.

Floor Width

(2) 3" (7,6 cm)

Screws

in each PWA

There will be an

overhang on

this end.

Flush Flush

PARTS REQUIRED:

x 108

2" (5,1 cm)

x 10

1-5/8" (4,1 cm)

x10

2 x 4 x 59-7/8" (5,1 x 10,2 x 152,1 cm)

QJA

RAFTER ASSEMBLY

6 x 24" (15,2 x 61 cm)

OSB OR WOOD GRAIN

1/4" (1,9 cm)

GAP

1/4" (1,9 cm)

GAP

QJA x2

Fig. A

1/4" (1,9 cm)

GAP

1/4" (1,9 cm)

GAP

Fig. C

Keep rafters  rmly against PVA at both ends when securing gusset.

Keep rafters tips  rmly against

PVA when securing gusset.

Repeat steps 1 - 3 to assemble three more rafters with two gussets.

Repeat steps 1 - 2 to assemble one rafter with only one gusset (Fig. D).

Remove PVA's from  oor.

Flip rafters over and attach a second gusset using glue and (12) 2" nails. No need to use jig for this step.

Keep QJA  rm against outside PVA's as shown (Fig.A) and push rafters tight to the middle PVA. Rafters should

touch at tips (Fig. A).

Apply glue to rafters where gusset will attach (Fig. B).

Place gusset onto QJA holding a 1/4" gap from edge (Fig. C) and keeping rafters  rm as instructed. Secure

gusset using one 1-5/8" screw into each rafter. HINT: These screws will help hold the measurements when you

nail on gussets.

Use ten 2" nails to  nish securing the gusset to the rafters to pattern shown in Fig. C.

BEGIN

Place two rafters QJA into the jig as shown.

YOU WILL BUILD 5 RAFTERS - ONE OF WHICH WILL HAVE ONLY 1 GUSSET

FINISH

You have  nished assembling your rafters.

FINISH

1-5/8" (4,1 cm)

Screw

QJA x2

Fig. B

Glue where

gusset installs

96-3/4"

(245,7 cm)

Fig. D

96-3/4"

(245,7 cm)

Glue where

gusset installs

BACK WALL FRAME

Toe-screw up through THA into SZ with two 3" screws.

BEGIN

3" (7,6 cm)

PARTS REQUIRED:

(2) 3" (7,6 cm)

Screws

3" (7,6 cm)

Nail

Fasten SZ to THA with one 3" nail as shown.

Orient parts on  oor as shown (Fig. A). Measure and mark.

Fig. A

2 x 4 x 73-1/2" (5,1 x 10,2 x 186,7 cm)

THA

2 x 4 x 89" (5,1 x 10,2 x 226,1 cm)

HINT:

89"

(2 26,1 cm)

44-1/2"

(113 cm)

73-1/2"

(186,7 cm)

44-1/2"

(113 cm)

1-1/2"

(3,8 cm)

3-1/2"

(8,9 cm)

3-1/2"

(8,9 cm)

3" (7,6 cm)

THA

FINISH

You have  nished building your back wall frame.

THA

2" (5,1 cm)

Place SP on at under THA for temporary support as shown.

BEGIN

BACK WALL PANELS

PARTS REQUIRED:

For squareness maintain 1-3/4"

measurement along panel edge.

3/8 x 48 x 76"

(1 x 121,9 x 193 cm)

Place 48" x 76" panel on frame with primed side facing up.

Use SP on edge to support the panel as shown.

x21

1-1/2" (3,8 cm)

Carefully ip the back wall frame over.

Hold panel ush against top plate SZ and keep 1-3/4" measurement along middle stud.

Nail using 1-1/2" and 2" nails spaced 6" apart.

2 x 4 x 48" (5,1 x 10,2 x 122 cm)

Temporary Support

76"

(193 cm)

48"

(121,9 cm)

1-3/4

(4,4 cm)

1-3/4

(4,4 cm)

(15,2cm)

SP (on edge)

Temporary Support

2" (5,1 cm)

Nails

SP (on at)

Temporary Support

THA

Flush

Primed side UP

1-1/2" (3,8 cm)

Nails

2" (5,1 cm)

3/8 x 48 x 76"

(1 x 121,9 x 193 cm)

Place panel on frame as shown with primed side facing up and  ush to installed panel.

Use SP to support frame and panel while nailing.

BACK WALL PANELS

PARTS REQUIRED:

FINISH

You have  nished installing your back wall panels.

x21

1-1/2" (3,8 cm)

Hold panel tight to the installed panel and tight against top plate.

Nail using 1-1/2" and 2" nails spaced 6" apart.

To draw panels tight

angle nail at seam.

76"

(193 cm)

48"

(121,9 cm)

(15,2cm)

2" (5,1 cm)

Nails

For squareness hold panel tight

against left panel and top plate.

2 x 4 x 48" (5,1 x 10,2 x 122 cm)

Temporary Support

Primed side UP

SP (on edge)

Temporary Support

1-1/2" (3,8 cm)

Nails

PARTS REQUIRED:

HINT:

Center on

marks.

TM x6

48"

(121,9 cm)

48"

(121,9 cm)

48"

(121,9 cm)

24"

(61 cm)

1-1/2"

(3,8 cm)

1-1/2"

(3,8 cm)

96"

(243,8 cm)

72"

(182,9 cm)

72"

(182,9 cm)

120"

(304,8 cm)

72"

(182,9 cm)

BEGIN

Orient parts on edge on  oor. Measure and mark.

Use two 3" nails at each mark.

Repeat STEPS 1 - 2 to build the second eave wall frame.

You have  nished building your eave wall frames.

EAVE SIDE WALL FRAMING

3" (7,6 cm)

FINISH

3" (7,6 cm)

Nails

x56

TOENAILING

IMPORTANT! YOU WILL BUILD TWO IDENTICAL EAVE SIDE WALLS.

2 x 4 x 72" (5,1 x 10,2 x 182,9 cm)

x16

2 x 4 x 48" (5,1 x 10,2 x 122 cm)

PARTS REQUIRED:

3/4"

GAUGE BLOCK

GAA

EAVE SIDE WALL PANELS

3/8 x 48 x 76" (1 x 121,9 x 193 cm)

2" (5,1 cm)

x45

Place a 48 x 76" panel onto wall frame with primed side up as shown.

Use the GAA gauge block to mark the 3/4" side measurement on the wall stud.

Keep panel ush along top of frame. Secure panel with two 2" nails in the corners (Fig. A).

Nail the panel using 2" nails 6" apart

on edges and 12" apart inside panel.

Ensure your wall frame is square by installing one panel and squaring frame.

Move to the opposite end. Using the long edge

of the panel as a lever, move the panel side-

to-side until you have a 3/4" measurement on

the wall stud. Secure corner with two 2" nails

(Fig. B).

For squareness maintain Flush and

3/4" measurement along panel edge.

BEGIN HERE

(15,2 cm)

3/4"

(1,9 cm)

3/4"

(1,9 cm)

48"

(121,9 cm)

12"

(30,5 cm)

Primed side UP

3/4" Gauge

Block

BEGIN

Fig. A

Fig. B

3/4"

(1,9 cm)

3/4"

(1,9 cm)

2 Nails

Flush

2 Nails

Flush

BEGIN HERE

Primed side UP

(15,2 cm)

48"

(121,9 cm)

23-7/8"

(60,6 cm)

12"

(30,5 cm)

2" (5,1 cm)

PARTS REQUIRED:

EAVE SIDE WALL PANELS

x1x1

x77

Place 23-7/8" x 76" panel on frame as shown with primed side facing up  ush with  rst

panel. Nail using 2" nails 6" apart on edges and 12" apart inside panel.

Place 48" x 76" panel on frame as shown with primed side facing up  ush with 23-7/8"

panel. Nail using 2" nails 6" apart on edges and 12" apart inside panel.

Repeat STEPS 1 - 5 to install second eave side wall panels.

You have  nished building your eave walls.

FINISH

Flush Flush Flush

To draw panels tight

at seams angle nail.

3/8 x 48 x 76"

(1 x 121,9 x 193 cm)

3/8 x 23-7/8 x 76"

(1 x 60,6 x 193 cm)

Page is loading ...

Heartland PRESTWICK Assembly Manual

Brand: Heartland

Model: PRESTWICK

Type: Assembly Manual

This manual is also suitable for

Architectural Series

Download PDF

report

Heartland PRESTWICK Assembly Manual

This manual is also suitable for

Heartland PRESTWICK Assembly Manual

Related papers

Other documents