Sony Cyber Shot DSC-U40 User manual

3-084-892-11(1)

Digital Still Camera

Operating Instructions

Before operating the unit, please read this manual thoroughly, and retain

it for future reference.

Owner’s Record

The model and serial numbers are located on the bottom. Record the

serial number in the space provided below. Refer to these numbers

whenever you call upon your Sony dealer regarding this product.

Model No. DSC-U40

Serial No.

DSC-U40

Getting started_______________________

_

Shooting still images _________________

_

Enjoying still images _________________

_

Enjoying movies _____________________

_

Deleting images______________________

_

Enjoying images on your computer

_____

_

Troubleshooting _____________________

_

Additional information________________

_

Index

_

____________________________

_

2

To prevent fire or shock hazard, do

not expose the unit to rain or

moisture.

If you have any questions about this product,

you may call:

Sony Customer Information Services Center

1-800-222-SONY (7669)

The number below is for the FCC related

matters only.

Regulatory Information

CAUTION

You are cautioned that any changes or

modifications not expressly approved in this

manual could void your authority to operate

this equipment.

Note:

This equipment has been tested and found to

comply with the limits for a Class B digital

device, pursuant to Part 15 of the FCC Rules.

These limits are designed to provide

reasonable protection against harmful

interference in a residential installation. This

equipment generates, uses, and can radiate

radio frequency energy and, if not installed

and used in accordance with the instructions,

may cause harmful interference to radio

communications. However, there is no

guarantee that interference will not occur in a

particular installation. If this equipment does

cause harmful interference to radio or

television reception, which can be determined

by turning the equipment off and on, the user

is encouraged to try to correct the interference

by one or more of the following measures:

– Reorient or relocate the receiving

antenna.

– Increase the separation between the

equipment and receiver.

– Connect the equipment into an outlet on a

circuit different from that to which the

receiver is connected.

– Consult the dealer or an experienced

radio/TV technician for help.

The supplied interface cable must be used

with the equipment in order to comply with

the limits for a digital device pursuant to

Subpart B of Part 15 of FCC Rules.

WARNING

For the Customers in the U.S.A.

This symbol is intended to

alert the user to the presence

of uninsulated “dangerous

voltage” within the product’s

enclosure that may be of

sufficient magnitude to

constitute a risk of electric

shock to persons.

This symbol is intended to

alert the user to the presence

of important operating and

maintenance (servicing)

instructions in the literature

accompanying the appliance.

Declaration of Conformity

Trade Name: SONY

Model No.: DSC-U40

Responsible Party:Sony Electronics Inc.

Address: 680 Kinderkamack

Road, Oradell, NJ 07649

U.S.A.

Telephone No.: 201-930-6972

This device complies with Part 15 of the

FCC Rules. Operation is subject to the

following two conditions: (1) This device

may not cause harmful interference, and

(2) this device must accept any interference

received, including interference that may

cause undesired operation.

3

CAUTION

TO PREVENT ELECTRIC SHOCK, MATCH

WIDE BLADE OF PLUG TO WIDE SLOT,

FULLY INSERT.

A moulded plug complying with BS1363 is fitted

to this equipment for your safety and

convenience.

Should the fuse in the plug supplied need to be

replaced, a fuse of the same rating as the supplied

one and approved by ASTA or BSI to BS1362

(i.e., marked with or mark) must be used.

If the plug supplied with this equipment has a

detachable fuse cover, be sure to attach the fuse

cover after you change the fuse. Never use the

plug without the fuse cover. If you should lose the

fuse cover, please contact your nearest Sony

service station.

This product has been tested and found

compliant with the limits sets out in the EMC

Directive for using connection cables shorter

than 3 meters (9.8 feet).

Attention

The electromagnetic fields at the specific

frequencies may influence the picture of this

camera.

Notice

If static electricity or electromagnetism causes

data transfer to discontinue midway (fail),

restart the application or disconnect and

connect the USB cable again.

Certain countries may regulate disposal of the

battery used to power this product. Please

consult with your local authority.

For the Customers in the U.S.A.

THIS DEVICE COMPLIES WITH PART 15

OF THE FCC RULES. OPERATION IS

SUBJECT TO THE FOLLOWING TWO

CONDITIONS:

(1) THIS DEVICE MAY NOT CAUSE

HARMFUL INTERFERENCE, AND

(2) THIS DEVICE MUST ACCEPT ANY

INTERFERENCE RECEIVED,

INCLUDING INTERFERENCE THAT MAY

CAUSE UNDESIRED OPERATION.

For the Customers in Canada

THIS CLASS B DIGITAL APPARATUS

COMPLIES WITH CANADIAN ICES-003.

For the Customers in the U.S.A.

and Canada

RECYCLING NICKEL METAL

HYDRIDE BATTERIES

Nickel Metal Hydride

batteries are recyclable.

You can help preserve our

environment by returning your

used rechargeable batteries to

the collection and recycling location

nearest you.

For more information regarding recycling

of rechargeable batteries, call toll free

1-800-822-8837, or visit

http://www.rbrc.org/

CAUTION:

Do not handle damaged or leaking Nickel

Metal Hydride batteries.

Notice for the customers in the

United Kingdom

Attention for the Customers in

Europe

“Memory Stick”

N50

4

Before using your camera

Trial recording

Before you record one-time events, you may want

to make a trial recording to make sure that the

camera is working correctly.

No compensation for contents of the

recording

Contents of the recording cannot be compensated

for if recording or playback is not possible due to

a malfunction of your camera or recording media,

etc.

Back up recommendation

To avoid the potential risk of data loss, always

copy (back up) data to a disk.

Notes on image data compatibility

• This camera conforms with the Design rule for

Camera File system universal standard

established by the JEITA (Japan Electronics

and Information Technology Industries

Association).

• Playback of images recorded with your camera

on other equipment and playback of images

recorded or edited with other equipment on

your camera are not guaranteed.

Notes on “Memory Stick Duo”

• There are two types of “Memory Stick”: a

normal size “Memory Stick” and a smaller

version called a “Memory Stick Duo.” You can

use only a “Memory Stick Duo” in this camera.

• This camera turns off whenever you open the

battery/“Memory Stick Duo” cover. Do not

open the battery/“Memory Stick Duo” cover

while the access lamp is lit.

Precaution on copyright

Television programs, films, video tapes, and other

materials may be copyrighted. Unauthorized

recording of such materials may be contrary to

the provision of the copyright laws.

Do not shake or strike the camera

In addition to malfunctions and inability to record

images, this may render the “Memory Stick Duo”

unusable or image data breakdown, damage or

loss may occur.

LCD screen, LCD finder (only models

with an LCD finder) and lens

• The LCD screen and the LCD finder are

manufactured using extremely high-precision

technology so over 99.99% of the pixels are

operational for effective use. However, there

may be some tiny black points and/or bright

points (white, red, blue or green in color) that

constantly appear on the LCD screen and the

LCD finder. These points are normal in the

manufacturing process and do not affect the

recording in any way.

• Be careful when placing the camera near a

window or outdoors. Exposing the LCD screen,

the LCD

finder or the lens to direct sunlight for

long periods may cause malfunctions.

• Do not press the LCD screen hardly. The screen

may be uneven and that may cause a

malfunction.

• Images may be trailed on the LCD screen in a

cold location. This is not a malfunction.

5

Clean the flash surface before use

The heat of flash emission may cause dirt on the

flash surface to become discolored or to stick to

the flash surface, resulting in insufficient light

emission.

Do not get the camera wet

When taking pictures outdoors in the rain or

under similar conditions, be careful not to get the

camera wet. If moisture condensation occurs, see

page 81 and follow the instructions on how to

remove it before using the camera.

Do not expose the camera to sand or

dust

Using the camera in sandy or dusty locations may

cause malfunction.

Note on the camera locations

Do not use the camera near a location that

generates strong radio wave or emits radiation.

The camera may not be able to record or play

back properly.

The pictures used in this manual

The photographs used as examples of pictures in

this manual are reproduced images, and are not

actual images shot using this camera.

Trademarks

• “Memory Stick Duo” and

are trademarks of Sony Corporation.

• “Memory Stick PRO Duo” and

are trademarks of

Sony Corporation.

• “MagicGate Memory Stick Duo” is a

trademark of Sony Corporation.

• “Memory Stick,” , and “MagicGate

Memory Stick” are trademarks of Sony

Corporation.

• “Memory Stick PRO” and

are trademarks of Sony Corporation.

• “MagicGate” and are

trademarks of Sony Corporation.

• Microsoft and Windows are registered

trademarks of the U.S. Microsoft Corporation

in the United States and other countries.

• Macintosh and Mac OS are trademarks or

registered trademarks of Apple Computer, Inc.

• Pentium is a trademark or a registered

trademark of Intel Corporation.

• In addition, system and product names used in

this manual are, in general, trademarks or

registered trademarks of their respective

developers or manufacturers. However, the

™

or ® marks are not used in all cases in this

manual.

How to hold the

camera

When shooting an image with the camera, be

careful not to obstruct the flash or the lens with

your fingers.

6

Table of contents

Before using your camera.........................4

How to hold the camera............................5

Identifying the parts..................................8

Preparing batteries ..................................10

Charging the batteries.............................10

Inserting the batteries..............................12

Using your camera abroad......................14

Turning on/off your camera....................14

How to use the buttons............................15

Setting the date and time.........................15

Inserting and removing a

“Memory Stick Duo”......................17

Setting the still image size ......................18

Image size...............................................19

Basic still image shooting

— Using auto adjustment mode.....20

Using the self-timer............................22

Selecting a flash mode........................23

Creating or selecting a folder..................24

Creating a new folder .........................25

Selecting the recording folder.............26

Shooting according to scene conditions

— Scene Selection..........................28

Setting the distance to the subject

— Focus preset...............................30

Shooting images continuously

— Burst.......................................... 31

Adjusting color tones

— White Balance........................... 33

Viewing still images on the LCD

screen ............................................. 35

Viewing single images....................... 35

Viewing an index screen

(four-image)................................... 36

Selecting the folder and playing back

images — Folder............................ 37

Enlarging an image

— Enlarged playback..................... 39

Choosing images to print

— Print (DPOF) mark.................... 40

Connecting your camera to a PictBridge

compliant printer............................ 42

Printing images....................................... 44

Shooting movies..................................... 46

Viewing movies on the LCD screen....... 49

Deleting images.......................................50

Formatting a “Memory Stick Duo”.........51

Copying images to your computer

— For Windows users....................53

Installing the USB driver....................54

Installing “Image Transfer”................55

Installing “ImageMixer”.....................56

Connecting the camera to

your computer.................................57

Copying images using

“Image Transfer”............................58

Changing “Image Transfer” settings...59

Copying images without using

“Image Transfer”............................59

Viewing images on your computer.....61

Image file storage destinations and

file names........................................62

Viewing images from your computer

with this camera..............................63

Copying images to your computer

— For Macintosh users ..................64

Creating a Video CD using

“ImageMixer”.................................66

Getting started

Shooting still images

Enjoying still images

Enjoying movies

Deleting images

Enjoying images on your

computer

7

Troubleshooting ......................................67

Warnings and messages ..........................75

Self-diagnosis display

— If a code starting with an

alphabet letter appears ....................77

Menu items..............................................78

Precautions..............................................81

On “Memory Stick” ................................83

On Nickel-Metal Hydride batteries.........84

On the battery charger.............................85

Specifications..........................................86

LCD screen displays ...............................87

Index........................................................89

Troubleshooting

Additional information

Index

8

Identifying the parts

See the pages in parentheses for details of operation.

51

2

3

4

6

7

8

A Shutter button (20)

B POWER button (14)

C POWER lamp (14)

D Lens cover (14)

E Mode switch

: To view images (35)

: To shoot still images (20)

To shoot images

continuously (31)

: To shoot movies (46)

F Flash (23)

G Self-timer lamp (23)

H Lens

9

7

8

9

q;

qa

qs

6

1

2

3

4

5

Attaching the neck strap

A LCD screen

B (Flash charge) lamp (orange)

(24)

C MENU button (15)

D Control buttons

Menu on: v/V (15)

Menu off: /SCENE (23, 28)

E EXEC/ (Enlarged playback)

button (15, 39)

F Hook for neck strap

G Battery/“Memory Stick Duo”

cover

H OPEN button (12)

I Access lamp (17)

J USB jack cover

K (USB) jack (57)

L RESET button (bottom surface)

(67)

10

Preparing batteries

Acceptable batteries

– HR11/45: HR03 (size AAA) Nickel-

Metal Hydride batteries (2)

NH-AAA-DA (2) (supplied)

NH-AAA-2DA twin-pack (not supplied)

– R03 (size AAA) alkaline batteries (2)

Batteries that cannot be used

Manganese batteries, lithium batteries,

Ni-Cd batteries

When the above batteries are used,

operation is not guaranteed due to possible

voltage drops or other characteristics of the

batteries.

In addition, the battery remaining indicator

is not displayed correctly.

• When alkaline batteries are used, take

note of the following information.

– The battery life is shorter than that of

the supplied Nickel-Metal Hydride

batteries.

– There is a big difference in the

performance of batteries of different

types and of batteries made by

different manufacturers. The battery

life may be quite a bit shorter

depending on the conditions under

which the batteries are used. This is

especially true in low temperatures,

where some batteries are noticeably

weaker.

You may not be able to shoot in

temperatures below 5°C (41°F).

– The battery remaining indicator will

not display the correct information.

The camera may turn off even when

the indicator shows that there is

power remaining, but this is not a

malfunction.

Charging the

batteries

, Insert Nickel-Metal Hydride

batteries into the battery

charger (supplied) with the

correct polarity +/–.

For details on the supplied battery charger,

see page 85.

• The supplied battery charger is only for

Nickel-Metal Hydride batteries. You

cannot charge any other type of battery.

• Be sure to charge the Nickel-Metal Hydride

batteries supplied with your camera before

using them for the first time.

• Connect the battery charger to an easily

accessible wall outlet (wall socket) close by.

1

G

e

tti

ng s

t

ar

t

e

d

11

Getting started

, Connect the battery charger to

a wall outlet (wall socket) using

the power cord (mains lead).

The CHARGE lamp lights up when

charging begins, and goes off when

charging is completed.

• Even if the CHARGE lamp is not lit, the battery

charger is not disconnected from the AC power

source (mains) as long as it is connected to the

wall outlet (wall socket). If some trouble occurs

while using the battery charger, immediately

shut off the power by disconnecting the plug

from the wall outlet (wall socket).

• When charging is finished, disconnect the

power cord (mains lead) from the wall outlet

(wall socket), and remove the Nickel-Metal

Hydride batteries from the battery charger.

Charging time

This represents the time required to charge

fully depleted Nickel-Metal Hydride

batteries using the supplied battery charger

in an environment where the ambient

temperature is 25°C (77°F).

• It takes about six hours to completely charge

the batteries. The CHARGE lamp may remain

lit longer than six hours, but this is not a

malfunction.

• If you use the BC-CSQ2 battery charger

supplied with the STAMINA “Super Quick

charge” kit (not supplied), the batteries will

charge faster.

Charging time for Size AAA Nickel-Metal

Hydride batteries

2 batteries: Approx. 1 hour 25 minutes

4 batteries: Approx. 2 hours 50 minutes

Notes on the Nickel-Metal

Hydride batteries

• If the poles of the Nickel-Metal Hydride

batteries are dirty, the batteries may not charge

properly. Occasionally clean the poles of the

batteries and the terminals of the charger by

wiping them with a dry cloth.

• Always use the supplied case when transporting

the Nickel-Metal Hydride batteries. If the

positive and negative terminals come into

contact with metallic material and are shorted,

the batteries could overheat or catch fire.

• At the time of purchase, or when the

Nickel-Metal Hydride batteries have not been

used for a long time, they may not fully charge.

This is typical of this type of battery, and is not

a malfunction. If this happens, repeatedly using

up the batteries fully, and then charging them,

should correct the problem.

• Even when Nickel-Metal Hydride batteries are

not being used they lose their charge naturally

over time. It is recommended that you recharge

the batteries just before using them.

• If you recharge Nickel-Metal Hydride batteries

before fully using up the existing charge, the

low battery warning may be displayed sooner

than expected. This is called the “memory

effect.”* If this problem occurs, charging the

batteries only after using up the existing charge

will correct it.

* The “memory effect” – the situation in which

the capacity of the battery is temporarily

lowered.

• Do not peel off the external seals or damage the

batteries. Never use batteries from which the

seals have been partially or completely

removed, or batteries that have been split in any

way. These may cause leakage, explosion, or

heat-up of the battery, and personal scald or

injury may be caused. These may cause a

malfunction of the battery charger.

2

To the wall outlet

(wall socket)

Power cord

(mains lead)

CHARGE lamp

Nickel-Metal Hydride

battery

Charging time

NH-AAA-DA × 2 (supplied) Approx. 6 hours

12

Inserting the batteries

, Open the battery/“Memory

Stick Duo” cover.

Hold the camera with the battery/“Memory

Stick Duo” cover up, then slide the cover in

the direction of the arrow 1 while pressing

OPEN. The battery/“Memory Stick Duo”

cover opens in the direction of the arrow 2.

, Insert the batteries.

Match the +/– poles of the batteries to the

+/– marks inside the battery case.

• From time to time, use a dry cloth to wipe any

dirt off of the battery terminals and the contacts

on the battery/“Memory Stick Duo” cover. Skin

oil and other dirt on the battery terminals and

contacts can significantly shorten the operating

time provided by the batteries.

, Close the battery/“Memory

Stick Duo” cover.

Close the battery/“Memory Stick Duo”

cover while holding the batteries in. Make

sure the cover is closed securely.

To remove the batteries

Hold the camera with the battery/“Memory

Stick Duo” cover facing upward, open the

cover, and remove the batteries.

• Be careful not to drop the batteries when

opening or closing the battery/“Memory Stick

Duo” cover.

1

2 3

13

Getting started

Battery remaining indicator

(When using Nickel-Metal

Hydride batteries)

As the battery power decreases with use, the

battery remaining indicator displays the

amount of power remaining using the

following symbols.

• If the LCD screen display is off, set

[DISPLAY] in [ ] to [ON] to check the

amount of power remaining.

• Based on the conditions under which the

camera is being used and the state of the

charge, or on the environment, this information

may not be correctly indicated.

• The battery remaining indicator is not

displayed in USB connecting.

Battery life and number of

images that can be recorded/

viewed

The tables show the approximate battery

life and the number of images that can be

recorded/viewed with fully charged

batteries at a temperature of 25°C (77°F) in

auto adjustment mode. The numbers of

images that can be recorded/viewed take

into account changing the supplied

“Memory Stick Duo” as necessary. Note

that the actual numbers may be less than

indicated depending on the conditions of

use.

Shooting still images

Under the average conditions

1)

Nickel-Metal Hydride batteries

Alkaline batteries

• When using Sony alkaline batteries

1) Shooting in the following situations:

– Shooting one time every 30 seconds

– The flash strobes once every two times

– The power turns on and off once every ten

times.

Viewing still images

2)

2) Viewing single images in order at about 3-

second intervals with [LCD LIGHT] set to

[ON]

Battery

remaining

indicator

Battery remaining

guidelines

Sufficient power remaining

Battery half full

Battery low, recording/

playback will stop soon.

Change the batteries for fully

charged ones, or charge these

batteries.

(The warning indicator flashes.)

Image

size

NH-AAA-DA (2) (supplied)

LCD

LIGHT

No. of

images

Battery

life (min.)

2M

ON Approx. 160 Approx. 80

OFF Approx. 180 Approx. 90

VGA

ON Approx. 160 Approx. 80

OFF Approx. 180 Approx. 90

Image

size

R03 (size AAA) alkaline

batteries (2) (not supplied)

LCD

LIGHT

No. of

images

Battery

life (min.)

2M

ON Approx. 50 Approx. 25

OFF Approx. 60 Approx. 30

VGA

ON Approx. 50 Approx. 25

OFF Approx. 60 Approx. 30

Image

size

NH-AAA-DA (2) (supplied)

No. of

images

Battery life

(min.)

2M Approx. 3800 Approx. 190

VGA Approx. 3800 Approx. 190

14

Shooting movies

3)

3) Shooting continuously at 160×112 image size

• The remaining indicator will decrease under the

following conditions:

– The surrounding temperature is low

– The flash is used

– The camera has been turned on and off many

times

– [LCD LIGHT] is set to [ON]

– The battery capacity decreases as you use it

more and more and as time passes (page 84).

NH-AAA-DA (2) (supplied)

Continuous

recording

LCD LIGHT

Battery life

(min.)

ON Approx. 90

OFF Approx. 110

Using your camera

abroad

Power sources

You can use your camera in any country or

region with the supplied battery charger

within 100 V to 240 V AC, 50/60 Hz. Use a

commercially available AC plug adaptor

[a], if necessary, depending on the design of

the wall outlet (wall socket) [b].

• Do not use an electronic transformer (travel

converter), as this may cause a malfunction.

BC-CS2A/CS2B

Turning on/off your

camera

, Slide the lens cover in the

direction of the arrow or press

POWER.

The POWER lamp (green) lights up and the

power is on. When you turn on your camera

for the first time, the DATE NOTATION

screen appears on the LCD screen

(page 15).

To turn off the power

Slide the lens cover in the opposite direction

of the arrow or press POWER again. The

POWER lamp goes out, and the camera

turns off.

• Slide the lens cover closed until it clicks into

place.

• If you open the lens cover too quickly, the

camera might not turn on. If this happens, close

the cover and then open it again more slowly.

POWER

POWER lamp

15

Getting started

Auto power-off function

If you do not operate the camera for about

three minutes, the camera turns off

automatically to prevent wearing down the

batteries.

However, the auto power-off function will

not operate when the camera is connected to

a computer with the USB cable.

How to use the

buttons

To change the current settings of the

camera, bring up the menu, and use the

control buttons to make the changes.

For each item, press MENU to display the

menu and press the control buttons v/V to

select the desired value, then press EXEC to

make the setting.

Press MENU, then the menu disappears

from the LCD screen.

EXEC/

MENU

Control

buttons

Setting the date

and time

, Slide the lens cover in the

direction of the arrow or press

POWER to turn on the power.

The POWER lamp (green) lights up and the

DATE NOTATION screen appears on the

LCD screen.

• To change the date and time, press MENU and

select [DATE&TIME SET] in [CLOCK SET]

under [ ] (page 80), then perform step 3.

When the setting is complete, press MENU so

that the CLOCK SET screen disappears from

the LCD screen.

• This operation is available no matter what

position the mode switch is in.

1

M/D/Y

D/M/Y

2003

12:00:00

AM

DATE NOTATION

1 1

Y/M/D

POWER

16

, Select the desired date display

format with the control buttons

v/V, then press EXEC.

Select from [Y/M/D] (year/month/day),

[M/D/Y] (month/day/year) or [D/M/Y]

(day/month/year). Then DATE&TIME

SET screen appears on the LCD screen.

• If the rechargeable button battery, which

provides the power for saving the time data, is

ever fully discharged (page 82), the DATE

NOTATION screen will appear again. When

this happens, reset the date and time, by starting

from step 2.

, Set the numeric value with the

control buttons v/V, then

press EXEC.

The item to be set is indicated with v/V.

After entering the number, v/V moves to

the next item. Repeat this step until all of

the items are set.

• Midnight is displayed as 12:00AM and noon is

displayed as 12:00PM.

• If you selected [D/M/Y] in step 2, set the time

on a 24-hour cycle.

, Select [OK] with the control

button v, then press EXEC.

The date and time are entered and the clock

starts to keep time.

• If you make a mistake, select [CANCEL] in

step 4 to display the DATE NOTATION

screen, then repeat the procedure from step 2.

• To cancel the date and time setting, select

[CANCEL], then press EXEC.

2

Y/M/D

12:00

AM

DATE&TIME SET

1 12003

EXEC/

3

Y/M/D

12:00

AM

DATE&TIME SET

2003 1 1

EXEC/

4

Y/M/D

10:30

AM

DATE&TIME SET

2003 7 4

CANCEL

OK

EXEC/

17

Shooting still images

Inserting and removing a “Memory Stick Duo”

, Open the battery/“Memory

Stick Duo” cover.

Hold the camera with the battery/“Memory

Stick Duo” cover up, then slide the cover in

the direction of the arrow 1 while pressing

OPEN. The battery/“Memory Stick Duo”

cover opens in the direction of the arrow 2.

• For details on the “Memory Stick Duo,” see

page 83.

, Insert the “Memory Stick Duo.”

Holding the “Memory Stick Duo” as shown

in the illustration, insert it all the way in

until it clicks.

• When you insert the “Memory Stick Duo,”

make sure it is facing in the correct direction,

and push it all the way in so that it is securely

seated in the connector. If the “Memory Stick

Duo” is not inserted correctly, you may not be

able to record or display images in the

“Memory Stick Duo.” This may also damage

the camera or the “Memory Stick Duo.”

• Be careful not to drop the batteries when

opening or closing the battery/“Memory Stick

Duo” cover.

, Close the battery/“Memory

Stick Duo” cover.

To remove a “Memory Stick Duo”

Open the battery/“Memory Stick Duo”

cover, then push the “Memory Stick Duo”

to pop it out.

• When the access lamp is lit up, it means

that image data is being read or written.

Never open the battery/“Memory Stick

Duo” cover or turn off the power at this

time, as the data may be damaged.

1

2

Terminal

side

3

Access lamp

Shooting still image

s

18

Setting the still image size

, Set the mode switch to , and

turn on the power, then press

MENU.

The menu appears on the LCD screen.

• Open the lens cover when closed.

, Select [ ] with the control

button v, then press EXEC.

Select [SIZE·BURST] with the

control buttons v/V, then

press EXEC.

The image size is displayed.

• For details on the image size, see page 19.

, Select the desired image size

with the control buttons v/V,

then press EXEC.

The image size is set.

When you press MENU, the menu

disappears and the indicator is displayed on

the LCD screen.

• The image size selected here is maintained even

when the power is turned off.

1

RETURN

FOCUS

SELFTIMER

WHITE BAL

AUTO

OFF

AUTO

SIZE

BURST

•

2M

MENU

2

RETURN

FOCUS

SELFTIMER

WHITE BAL

AUTO

OFF

AUTO

SIZE

BURST

•

2M

EXEC/

3

SIZE • BURST

BURST

VGA

2M

BURST

VGA

2M

EXEC/

19

Shooting still images

Image size

You can choose the image size (number of

pixels) according to the kind of images you

want to shoot. The larger you make the

image size, the better your image, but also

the larger the amount of data needed to

preserve your image. This means you can

save fewer images in your “Memory Stick

Duo.”

Choose an image size appropriate for the

kind of images you want to shoot.

* The factory setting is [2M].

Image size Examples

2M*

(1632×1224)

Printing postcard size

images

VGA

(640×480)

• Shooting more images

• Attaching images to

e-mail or creating home

pages

Number of images that can be saved in a “Memory Stick Duo”

(Units: number of images)

• When the images recorded using earlier Sony

models are played back, the image size

indication may be different from the actual

image size.

• Images viewed on the LCD screen of the

camera all appear the same size.

• The actual number of images may differ

depending on the shooting conditions.

• When the number of remaining shooting

images is greater than 9,999, >9999 indicator

appears on the LCD screen.

Capacity

8MB 16MB 32MB 64MB 128MB MSX-M256 MSX-M512

Image size

2M 14 29 60 122 245 445 906

VGA 80 161 326 656 1316 2380 4840

20

Basic still image shooting — Using auto adjustment mode

, Set the mode switch to , and

slide the lens cover to turn on

the power.

The name of the folder where the image will

be recorded appears on the LCD screen for

approximately five seconds.

• [FOCUS] is set to [AUTO] at the factory.

• The exposure is automatically adjusted.

• This camera can create new folders and select

folders to be stored in the “Memory Stick Duo”

(page 24).

, Hold the camera steadily with

both hands and position the

subject in the center of the LCD

screen.

Do not cover the lens or flash with your

fingers.

• When recording outdoors during clear weather

or under other intense light, undesired light

(ghosting) may enter the screen. If this

happens, shade the lens with your hand or other

object while recording.

• The exposure and focus are adjusted to the

center of the LCD screen.

, Press and hold the shutter

button halfway down.

A beep sounds. When the AE/AF lock

indicator changes from flashing to light-up,

the camera is ready for shooting.

• If you release the shutter button, the recording

will be canceled.

• When the camera does not beep, the AF

adjustment is not complete. You can continue to

shoot, but the focus is not adjusted properly.

• This camera employs an auto-macro AF

function. The minimum focal distance to the

subject is 10 cm (4 inches).

1 2

3

10

101

2M

AE/AF lock

indicator

Flashes green

t Lights up

Page is loading ...

Sony Cyber Shot DSC-U40 User manual

This manual is also suitable for

Sony Cyber Shot DSC-U40 User manual

Related papers

Other documents