sks CAGE SHIFTER + User manual

  • Hello! I've reviewed the user manual for the SKS GERMANY Cage Shifter 11887. This document details two ways to mount the device on your bike, using bottle cage holes or as an anywhere solution. It provides clear instructions on how to prepare the CAGE SHIFTER+, attach accessories, and ensure secure mounting using screws and hook and loop fasteners. I'm ready to answer any questions you have about the device or its installation.
  • What should I do before mounting the CAGE SHIFTER+?
    What kind of screws should I use?
    What should I do after securing the CAGE SHIFTER+?
GERMANY
MANUAL ¬ CAGE SHIFTER+ ¬ 11887 ALLROAD ROAD MOUNTAIN
EN . Scope of delivery
A 1x
CAGE SHIFTER+ with mounted nuts & bolts
B
4x Klett-Strap short
C
4x Accessory adapter
D
2x Klettstrap long, with rubber strap
E
2x Frame protection lm
D 2x B 4x A 1x
C 4x
E 2x
EN . Variation 1: Use on the bottle cage holes
01 EN .
Preparing the CAGE SHIFTER+ (A):
a. Attach the required accessory adapters (C) to the wings
of the CAGE SHIFTER+ (A).
b. Route the short hook and loop fasteners (B) through the
opening on the prepared CAGE SHIFTER+ (C) with the
hook and loop side facing the bike.
02 EN .
Screw the CAGE SHIFTER+ (A) to the frame in the desired
direction. Screw the bottle holder to the CAGE SHIFTER+
(A) with the screws supplied
Attention: Only use the screws supplied to avoid damage
to the frame.
03 EN .
Secure the accessory with the short hook and loop fasteners
(B) and shorten all protruding hook and loop fasteners.
GERMANY
MANUAL ¬ CAGE SHIFTER+ ¬ 11887 ALLROAD ROAD MOUNTAIN
03 EN .
Apply frame protection lm (E) at the necessary points; clean
these points beforehand. Secure the CAGE SHIFTER+ (A)
with the long hook and loop fasteners with a rubber tab (D)
at the desired point. Make sure that the rubber tab is ush
between the CAGE SHIFTER+ (A) and the frame. Tighten
the hook and loop fasteners securely with the rubber tab (D)
for a secure hold.
02 EN .
c. Route the short hook and loop fasteners (B) through
the opening on the prepared CAGE SHIFTER+
with the hook and loop side facing the bike.
Tip: Use the long hook and loop fastener with a rubber tab (D)
as a guide. To do this, attach the short (B) and long hook and
loop fasteners (D) to each other and pull them together through
the opening.
EN . Safety information:
Check that the CAGE SHIFTER+ is securely mounted
every day before setting out on your bike
Shorten hook and loop fasteners that are too long
(risk of accident)
Mount the CAGE SHIFTER+ only where it cannot come
into contact with the tyre / spokes. Risk of accident!
Only use the screws and hook and loop fasteners
supplied to avoid damage to the frame
Use frame protection lm to avoid damage to the frame.
04 EN .
Screw the bottle holder to the CAGE SHIFTER+ (A) with the
screws supplied.
Attention: Only use the screws supplied to avoid damage to
the frame. Secure the accessory with the short hook and loop
fasteners (B). Shorten all protruding hook and loop fasteners.
EN . Variation 2: Use as ANYWHERE solution
01 EN .
Preparing the CAGE SHIFTER+ (A):
a. Attach the required accessory adapters (C) to the wings
of the CAGE SHIFTER+ (A).
b. Route the long hook and loop fasteners with a rubber tab
(D) from below through the opening on the prepared CAGE
SHIFTER+ (C) as indicated.
2x
/