Raymarine DSM30 User manual

Brand: Raymarine

Model: DSM30

Type: User manual

This manual is also suitable for

DSM300 & DSM30

Digital Sounder

Module

Installation Manual

Document number: 87080-1

Date: November 2006

Trademarks and registered trademarks

HSB, Raymarine and SeaTalk are registered trademarks of Raymarine plc.

All other product names are trademarks or registered trademarks of their

respective owners.

Contents of this handbook ©Raymarine 2006

Contents

Trademarks and registered trademarks ............................................ 2

Important Information .........................................................................................5

Intended Use .......................................................................................... 5

Safety Notices ...................................................................................... 5

EMC Conformance ................................................................................. 6

Declaration of Conformity ................................................................ 6

Product Disposal .................................................................................... 6

Waste Electrical and Electronic Equipment (WEEE) Directive ........... 6

Warranty .............................................................................................. 6

Chapter 1: DSM Installation ..............................................................................7

1.1 Introduction ........................................................................................... 7

Planning the Installation ........................................................................ 7

EMC Installation Guidelines ................................................................. 7

Suppression Ferrites ......................................................................... 8

Connections to Other Equipment ..................................................... 8

1.2 Unpacking and Inspecting the Components ........................................... 9

Cable Options ...................................................................................... 10

1.3 Selecting Sounder Module Mounting Location .................................... 10

1.4 Mounting the Sounder Module ........................................................ 11

1.5 Cable Runs ......................................................................................... 14

1.6 System Connections ........................................................................... 14

Transducer Connection ...................................................................... 15

DC Power Connection ........................................................................ 15

Ground Connection ............................................................................ 18

1.7 Display Configuration ...................................................................... 18

Configuring E Series Displays ............................................................. 18

Configuring C Series Displays ............................................................. 19

Configuring hsb2 PLUS (Pathfinder) Series Displays ........................... 20

Chapter 2: Maintenance and Problem Solving ...............................................21

2.1 Maintenance ........................................................................................ 21

Routine Checks .................................................................................... 21

Cleaning Instructions ........................................................................... 21

EMC Servicing and Safety Guidelines ................................................... 22

2.2 Resetting the System ............................................................................ 23

For E Series and C Series Displays... ................................................ 23

For hsb2 PLUS Series Displays... ..................................................... 23

2.3 Problem Solving ................................................................................... 25

Common Problems and Their Solutions ................................................ 25

Status LED .......................................................................................... 26

4 DSM300 and DSM30 Installation Manual

2.4 How to Contact Raymarine ...................................................................28

On the Internet .....................................................................................28

Customer Support ..........................................................................28

In the US ...............................................................................................28

Accessories and Parts .....................................................................28

Technical Support ...........................................................................29

Product Repair and Service .............................................................29

In Europe ..............................................................................................30

Technical Support ...........................................................................30

Accessories and Parts .....................................................................30

Worldwide Support ..............................................................................30

Appendix: Specifications...............................................................................31

General .................................................................................................31

Sounder Features ..................................................................................31

Index ......................................................................................... 33

Important Information

Raymarine DSM300 and DSM30 Digital Sounder Modules provide echo sounder

data that can be displayed on Raymarine E Series, C Series, and hsb

PLUS

(Pathfinder) Series display units.

This manual contains important information for installing and maintaining your

Digital Sounder Module. Raymarine’s Technical Services representatives or your

local dealer will be available to answer any questions you may have.

Instructions on how to operate the fishfinder application can be found in the

handbook for your particular display system.

Intended Use

DSM300 and DSM30 Digital Sounder Modules are intended for depth finding and

fishfinding purposes on recreational (non-IMO/SOLAS class) boats. Echo

sounders require an appropriate Raymarine transducer and interconnecting

cable.

Safety Notices

This equipment must be installed and operated in accordance with the

instructions contained in this manual. Failure to do so can result in personal injury

and/or navigational inaccuracies. In particular:

CAUTION: High Voltage

Digital Sounder Modules contains high voltages. Adjustments require specialized

service procedures and tools only available to qualified service technicians – there

are no user serviceable parts or adjustments. The operator should never remove

the cover or attempt to service the equipment.

CAUTION: Transducer Cable

Removing the transducer cable from the rear of the DSM300 or DSM30 while the

sounder module is powered on can cause sparks. Only remove the transducer

cable after power has been removed from the DSM. As with any electronic device,

be sure the sounder module is mounted where it is well ventilated and free from

gasoline fumes.

If the transducer cable is accidentally removed while the DSM is powered on,

remove power from the sounder module, replace the transducer cable, and then

return power to the module. As a safety feature, the sounder module only

recognizes that the transducer is connected at power-up.

6 DSM300 and DSM30 Installation Manual

EMC Conformance

All Raymarine equipment and accessories are designed to the best industry

standards for use in the recreational marine environment.

The design and manufacture of Raymarine equipment and accessories conform to

the appropriate Electromagnetic Compatibility (EMC) standards, but correct

installation is required to ensure that performance is not compromised.

Declaration of Conformity

Raymarine plc declare that the DSM300 and DSM30 Digital Sounder Modules are

in compliance with the essential requirements of EMC directive 2004/108/EC.

The original Declaration of Conformity certificate may be viewed on the relevant

product page at www.raymarine.com.

Product Disposal

Waste Electrical and Electronic Equipment (WEEE) Directive

The WEEE Directive requires the recycling of waste electrical and electronic

equipment. While the WEEE Directive does not apply to some of Raymarine’s

products, we support its requirements as part of our environmental policy and we

ask you to be aware of how you should dispose of this product.

The wheelie bin symbol found on our products signifies that it should not be

disposed of in general waste or landfill. Please contact your local dealer, national

distributor or Raymarine Technical Services for information on product disposal.

Warranty

To register your Digital Sounder Module ownership, please take a few minutes to

fill out the warranty registration card found at the end of this handbook. It is very

important that you complete the owner information and return the card to the

factory in order to receive full warranty benefits.

Chapter 1: DSM Installation

1.1 Introduction

This chapter provides details for mounting the DSM300 and DSM30 and

connecting to the display.

For the system to display depth, water temperature and speed, you must install

the transducer type(s) capable of transmitting the appropriate data.

Planning the Installation

Before you install your system, plan the installation, considering:

• Location of the sounder module, as described in Section 1.3

• Cable Runs, as described in Section 1.5

• Correct transducer for your application

EMC Installation Guidelines

All Raymarine equipment and accessories are designed to the best industry

standards for use in the recreational marine environment.

Their design and manufacture conforms to the appropriate Electromagnetic

Compatibility (EMC) standards, but correct installation is required to ensure that

performance is not compromised. Although every effort has been taken to ensure

that they will perform under all conditions, it is important to understand what

factors could affect the operation of the product.

The guidelines given here describe the conditions for optimum EMC performance,

but it is recognized that it may not be possible to meet all of these conditions in all

situations. To ensure the best possible conditions for EMC performance within the

constraints imposed by any location, always ensure the maximum separation

possible between different items of electrical equipment.

For optimum EMC performance, it is recommended that wherever possible:

• Raymarine equipment and cables connected to it are:

• At least 5 ft (1.5 m) from any equipment transmitting or cables carrying

radio signals, e.g., VHF radios, cables and antennas. In the case of SSB

radios, the distance should be increased to 7 ft (2 m).

• More than 7 ft (2 m) from the path of a radar beam. A radar beam can nor-

mally be assumed to spread 20 degrees above and below the radiating

element.

8 DSM300 and DSM30 Installation Manual

• The equipment is supplied from a separate battery from that used for engine

start. Voltage drops below 10 V and starter motor transients can cause the

equipment to reset.

This will not damage the equipment, but may cause the loss of some informa-

tion and may change the operating mode.

• Raymarine specified cables are used. Cutting and rejoining these cables can

compromise EMC performance and must be avoided unless doing so is

detailed in the installation manual.

• If a suppression ferrite is attached to a cable, this ferrite should not be

removed. If the ferrite needs to be removed during installation it must be reas-

sembled in the same position.

Suppression Ferrites

The following illustration shows typical cable suppression ferrites used with

Raymarine equipment. Always use the ferrites supplied by Raymarine.

Connections to Other Equipment

If your Raymarine equipment is to be connected to other equipment using a cable

not supplied by Raymarine, a suppression ferrite must always be attached to the

cable that is closest to the Raymarine unit.

D3548-3

Chapter 1: DSM Installation 9

1.2 Unpacking and Inspecting the Components

Unpack your system carefully, to prevent damage to the equipment. Save the

carton and packing, in case you need to return the unit for service. Check that you

have all the correct system components:

Power Cable, 3m

part no. R69053

Mounting Screws,

No.8 (x4)

D9598-1

DSM300 Digital Sounder Module,

part no. E63069

C Series Network Cable, 3m

part no. E65010

hsb

adapter, 4-pin to 3-pin

part no. R69081

Operation Manual for PLUS

Displays, part no. 81249

DSM300

Operation

Manual

DSM300

Installation Manual,

part no. 87080

DSM300

& DSM30

Installation

Manual

Power Cable, 3m

part no. R69053

Mounting Screws, No.8 (x4)

D9599-1

DSM30 Digital Sounder Module,

part no. E63074

C Series Network Cable, 3m

part no. E65010

Installation Manual,

part no. 87080

DSM300

& DSM30

Installation

Manual

DSM30

10 DSM300 and DSM30 Installation Manual

A 3m-long cable is included for connecting your sounder module to a C Series or

hsb

PLUS (Pathfinder) Series display. Longer cables and connection cables for

other types of systems must be purchased separately.

Note:

C Series displays have 4-pin connectors while the older hsb

PLUS Series displays

have a 3-pin configuration. This requires that you use a 4-pin to 3-pin adapter (Raymarine

part number R69081) when connecting a sounder module to an hsb

PLUS Series display.

This adapter is included with the DSM300 but must be ordered separately with a DSM30.

Select from the following cable options:

1.3 Selecting Sounder Module Mounting Location

DSM300 and DSM30 sounder modules are waterproof to IPX-7 is and is designed

to be mounted either above or below deck.

Mount the DSM where it is:

• protected from physical damage and excessive vibration

• protected from prolonged exposure to rain, salt spray and direct sunlight

• well ventilated

• as close to the transducer as possible

Do not locate the DSM:

• in the engine compartment

• on the main console

When planning the installation, the following should be considered to ensure

reliable and trouble free operation:

•

Access: There must be sufficient space below the unit to enable cable con-

nections to the panel connectors, avoiding tight bends in the cable.

Cable Options

System Cable Part No.

E Series

SeaTalk

Network Cable, RJ-45, 1.5m

SeaTalk

Network Cable, RJ-45, 5m

SeaTalk

Network Cable, RJ-45, 10m

SeaTalk

Network Cable, RJ-45, 20m

E55049

E55050

E55051

E55052

C Series C Series Network Cable, 4-pin-to-4-pin, 10m E65011

hsb

PLUS Series

(Pathfinder)

hsb

In Line Terminator

hsb

Splitter Cable

hsb

Adapter Cable, 4-pin to 3-pin

R58117

E55040

R69081

Chapter 1: DSM Installation 11

• Interference: The selected location should be far enough away from

devices that may cause interference, such as motors, generators, and radio

transmitter/receivers. (See the EMC guidelines earlier in this chapter.)

•

Magnetic compass: Mount the unit at least 3 ft (1 m) away from a magnetic

compass.

•

Cable runs: The unit must be located near a DC power source. The power

cable supplied is 10 ft (3 m).

•

Environment: Provide good ventilation to prevent overheating.

CAUTION: Do Not Remove the Transducer Cable

Removing the transducer cable from the sounder module while

power is turned on can cause sparks. As with any electronic

device, be sure the sounder module is mounted where it is well

ventilated and free from gasoline fumes.

1.4 Mounting the Sounder Module

The DSM can be mounted either above or below deck using the supplied

hardware. To allow for ease of cable connection, mount the sounder module so

that the cables hang below the unit.

9.96 in (252.9 mm)

D7468-1

3.46 in

(88 mm)

9.51 in (241.6 mm)

10.76 in (273.3 mm)

7.37 in (187.2 mm)

Weight: 2.2 lbs (1.0 Kg)

Compass Safe Distance: 39 in (1 m)

2.43 in

(61.7 mm)

1.65 in

(41.8 mm)

12 DSM300 and DSM30 Installation Manual

To mount the DSM:

1. Hold the module in the location where you want to mount it, making sure it is

perpendicular to the deck.

2. Mark the location of the four key holes onto the mounting surface.

3. Drill a 9/64" pilot hole at each of the marked locations.

Vertical

D7479-1

Vertical

D7538-1

Chapter 1: DSM Installation 13

Note:

For fiberglass with a gelcoat surface, you should overdrill the surface to prevent the

gelcoat from chipping when driving in the screw. Before drilling the pilot hole, hand drill

the marked location with an oversized bit and countersink to approximately 3/8" diame-

ter.

4. Drive the supplied #8 screws into the pilot holes. Screw them in about half way.

5. Mount the module to the surface, slipping the screw heads through the four

key holes.

6. Press the module downward so the screws align with the narrow end of the

keyholes.

7. Tighten the screws. Do not overtighten.

6 mm

minimum

D7480-1

D7469-1

14 DSM300 and DSM30 Installation Manual

1.5 Cable Runs

Consider the following before installing the system cables:

• You will need to attach power, transducer, and display cables.

• All cables should be adequately secured, protected from physical damage,

and protected from exposure to heat.

• Avoid running cables through bilges or doorways, or close to moving or hot

objects.

• Avoid sharp bends.

• Use a watertight feed-through wherever a cable passes through an exposed

bulkhead or deckhead.

• Secure cables in place using tie-wraps or lacing twine. Coil any extra cable

and tie it out of the way.

1.6 System Connections

The connector panel provides the following connection sockets:

•

T/D, 7-pin socket for connecting to the transducer

•

HSB2, 4-pin socket for connecting to a C Series or hsb

PLUS Series display

•

POWER, 3-pin socket; two for connecting to boat’s DC power and one RF

ground (screen) connection

•

SEATALK HS, RJ-45 socket for connecting to an E Series display

CAUTION:

To protect exposed pins, please place the attached dust cover

over the socket (4-pin or RJ-45) to which you are not connecting a

cable.

D7464-2

10.7 to 18 VDC (DSM30)

E Series Display

Transducer

C Series or hsb PLUS

10.7 to 32 VDC (DSM300),

Chapter 1: DSM Installation 15

Transducer Connection

A 30 ft (10 m) cable is supplied with the transducer. This cable has a connector

plug (with an outer nut that you must attach) at one end for attaching to the

“T/D” connector on the sounder module. Optional extension cables are available.

CAUTION: Do Not Cut or Splice the Transducer Cable

• There is high voltage on the transducer cable. Splicing could

create a safety hazard.

• Cutting the transducer cable severely reduces sonar

performance. If the cable is cut, it must be replaced—it cannot

be repaired.

• Cutting the transducer cable will void the warranty and

invalidate the European CE mark.

DC Power Connection

The DSM300 is intended for use on boat’s DC power systems rated from 10.7 V to

32 V. The DSM30 is intended for use on boat’s DC power systems rated from 10.7

V to 18 V (12 volt systems only).

The power connection to the unit should be made at either the output of the

battery isolator switch or at a DC power distribution panel. Power should be fed

directly to the DSM via its own dedicated cable system and protected by a thermal

circuit breaker or fuse on the red (positive) wire that is installed close to the power

connection.

A10 ft (3 m) power cable is supplied with the unit. This cable has a connector plug

at one end for attaching to the “POWER” connector on the sounder module and

3 wires at the other end for connecting the power supply. The power cable may be

extended by up to 60 ft (20 m) using a wire gauge of AWG 12 or greater.

The RED wire must be connected to the feed from the positive (+) battery terminal

and the BLACK wire to the feed from the negative (–) battery terminal. The shield

wire (drain) should be connected to the boat’s RF ground. See “Ground

Connection” on page 18.

Install a quick blow 8 amp fuse on the red (positive) wire.

CAUTION: If the power connections are accidentally reversed the

system will not work. Use a multimeter to ensure that the input

power leads are connected for correct polarity.

DC power is connected at the 3-pin POWER connector on the unit’s connector

panel. The connector (viewed from the outside) and pin functions are shown in

the following diagram and table.

16 DSM300 and DSM30 Installation Manual

There is no power switch on the DSM. The unit turns on when the power cord is

attached to boat’s power and plugged into the POWER connector on the

connector panel.

Note:

You should locate the DSM so that the power cord can be easily removed, if

necessary. If the sounder is placed in a difficult-to-reach location, Raymarine strongly

suggests installing an on/off switch on the DSM power cord at a point where it is easily

accessible.

Power Connections with an E Series Display

Pin No. Function Color

1 Battery positive Red

2 Battery negative Black

3 Shield (drain wire) No insulation

D6162-1

D9600-1

Transducer

Sounder Module

E Series Display Unit

Power Supply

Chapter 1: DSM Installation 17

Power Connections with a C Series Display

Power Connections with an hsb

PLUS Series Display

D9601-1

Transducer

Sounder Module

C Series Display Unit

Power Supply

D9602-1

Transducer

Sounder Module hsb PLUS Series Display UnitPower Supply

18 DSM300 and DSM30 Installation Manual

Ground Connection

It is important that an effective RF ground is connected to the system. A single

ground point should be used for all equipment. You can ground the sounder

module by connecting the drain wire (shield) of the Power Input cable to the

boat’s RF ground. If you need to extend the wire, the extension wire should be an

8 mm braid or AWG 10 multi-stranded cable. If your boat does not have an RF

system, connect the drain wire to the negative battery terminal.

The DC system should be either:

• Negative grounded, with the negative battery terminal connected to the

boat’s ground.

• Floating, with neither battery terminal connected to the boat’s ground.

This system is not intended for use on “positive” ground vessels.

1.7 Display Configuration

The DSM must be connected to an hsb

PLUS Series, C Series or E Series display

unit to show echo sounder data. How you configure your sounder module

depends on the type of display to which you will be connecting it.

Configuring E Series Displays

The E Series system operates on the SeaTalk

network. E Series cables have an

RJ-45 modular connector that attach to the “SEATALK HS” connector on the

sounder module. See “Cable Options“ on page 10 for a list of available E Series

cables. When the DSM is used with a single display, connection is made via a

SeaTalk

Crossover Coupler.

Configuring an E Series System - Single Display

E Series Display

Sounder Module

SeaTalk

Cable

SeaTalk

Cable

Crossover Coupler

E55060

D9603-1

Chapter 1: DSM Installation 19

When used in a multiple display system, connect the DSM to the SeaTalk

Network Switch.

Configuring an E Series System - Multiple Displays

Configuring C Series Displays

The C Series system uses cables with a round 4-pin twist-lock network connector.

A 3m-long C Series cable is included with your sounder module and is also

available in a 10 m length (Raymarine part number E65011). The display cable

attaches to the 4-pin male connector labelled “HSB2”on the connector panel of

the sounder module.

Configuring a C Series System

E Series Display

DSM

SeaTalk

Network Switch

E55058

SeaTalk

Cable

SeaTalk

Cable

SeaTalk

Cable

D9604-1

C Series Display

Sounder Module

4-pin to 4-pin C Series Cable

D9605-1

20 DSM300 and DSM30 Installation Manual

Configuring hsb

PLUS (Pathfinder) Series Displays

hsb

PLUS network cables have a triangular 3-pin connector on both ends. When

using the DSM with an hsb

PLUS Series display, connect the supplied 4-pin to

3-pin hsb

adapter between the sounder module and the network cable.

The hsb

system must be terminated at both ends of the network. If a PLUS Series

display is the last device on the network, an inline terminator is installed on the

cable where it connects to the display. The network connection in the DSM,

however, is internally terminated; it does not require an inline terminator.

Because the sounder module is internally terminated, it must be

installed at the end of the hsb

network. You must not use an inline

terminator on the DSM end of the network. If an hsb

splitter is

used, connect it to a display and not to the DSM.

Configuring an hsb

PLUS System - Single Display

Configuring an hsb

PLUS System - Multiple Displays

3-pin to 3-pin hsb

cable

R69081

Sounder Module

R58117

hsb

Inline

Terminator

4-pin to 3-pin

hsb

adapter

D9606-1

hsb

PLUS Series Display

Sounder Module

R55040

3-pin hsb

cable3-pin hsb

cable

hsb

Splitter

R58117

hsb

Inline

Terminator

R69081

4-pin to 3-pin

hsb

adapter

D9607-1

hsb

PLUS Series Display hsb

PLUS Series Display

Page is loading ...

Raymarine DSM30 User manual

Brand: Raymarine

Model: DSM30

Type: User manual

This manual is also suitable for

Download PDF

report

Raymarine DSM30 User manual

This manual is also suitable for

Raymarine DSM30 User manual

Related papers

Other documents