5
6
7
PoE Injector/Splitter Kit
Model No.: SP391
http://www.micronet.info
Quick Installation Guide
Specification
CE Mark Warning
This equipment complies with the requirements relating to
electromagnetic compatibility, the essential protection
requirement of Council Directive 89/336/EEC on the
approximation of the laws of the Member States relating to
electromagnetic compatibility.
Company has an on-going policy of upgrading its products and
it may be possible that information in this document is not up-
to-date. Please check with your local distributors for the latest
information. No part of this document can be copied or
reproduced in any form without written consent from the
company.
Trademarks:
All trade names and trademarks are the properties of their
respective companies.
Copyright c 2008, All Rights Reserved
Model
External
Power Supply
Power
Splitter
Module
Power Injector
Module
Power Jack
Diameter
Environment
Emission
Input Voltage : AC 100 - 240V
Ouput Voltage : 24V DC
Output Current : 1A (max)
Input Voltage : 24V DC
Ouput Voltage : 5V / 7.5V / 9V / 12V
Output Current : 1.5A (max)
Input Voltage : 24V DC
Output Voltage : 24V DC
2.1mm (Inside diameter)
5.5mm (Outside diameter)
OO
: -10 C - 40 C
5% - 90%
CE
Operating Temperature
Operating Humidity :
SP391
2
Physical Description
1
Installation
3 4
RJ-45 for Data and Power
LED Indicators
Power Jack (Power In 24V)
RJ-45 for Data
DC Power Connector (Power Out)
Introduction
Micronet Power over Ethernet (POE) Injector/Splitter Kit SP391,
with adjustable output 5V/ 7.5V/ 9V/ 12V, effectively provides
Ethernet data and DC power to a non-PoE Ethernet terminals
such as IP Telephone sets, wireless access point, and Internet
camera. The technology incorporates electrical power onto a
LAN data line enabling the delivery of operating power in
addition to datacom to Ethernet terminals over standard cabling
infrastructure.
Package Contents
Before you start installing the device, verify the following items
are in the package:
PoE Injector
PoE Splitter
Power Cord
Quick Installation Guide
Power Adapter
Features
Convey the power to your LAN equipment through Ethernet
cable
Compliant with Micronet wireless AP, IP phone and internet
camera
Adjustable Splitter ouput: DC output 5V/ 7.5V/ 9V/ 12V
via DIP switch
Power LED indication
Injector
2
Splitter
1
43
5
1
2
3
4
5
WARNING:
Connect the Injector with Splitter only. Connecting the
Injector directly to other devices may cause serious damage!
SP391 does not comply with IEEE802.3af. Don't connect
any of it to IEEE802.3af devices.
For safety reason, SP391 will only support device with output
voltage below 12V/1.5A. Please make sure the remote
Ethernet device is under the range of 5V, 7.5V, 9V, 12V.
Injector
Splitter
Connect to End Device
Connect to AC Outlet
(100~240V)
Connect to End
Device's DC Jack
Connect to Switch/HUB
(Data Input)
AC/DC Power Adapter
-
1
-
2
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
Other documents
-
Lantech POS-100A User manual
-
Allied Telesis AT-6102 User manual
-
UNICOM Electric POE-22001G User manual
-
Tycon Systems 5600033 Datasheet
-
Trendnet TPE-111GI Owner's manual
-
Trendnet TPE-101I Owner's manual
-
-
-
-