MicroNet SP390BI User manual

MicroNet
Brand
MicroNet
Model
SP390BI
Category
Network splitters
Type
User manual
3
21
4
Installation
To install the SP390BI lnjector, please follow below steps.
1.Using RJ-45 cable to connect the DATA IN port on the SP390BI
with the switch (which is Data out port).
2. Using RJ-45 cable to connect the DATA OUT port in SP390.BI to
connect with the PoE Splitter (SP390BS)
3. Plug in the power cable of the PoE Splitter to the PD’s power
plug.
4. Before starting, make sure all connect are correct and the voltage
is right.
● The SP390BI connects to the splitter in the DATA OUT port.
● The SP390BI connect to the switch with DATA IN port.
● The POWER IN port is outlet to get the power supply to
SP390BI form wall power plug.
Introduction
Micronet Power over Ethernet (PoE) Injector P390BI is
revolutionary technology for powering Ethernet terminals such as IP
Telephone sets, wireless access point, Internet camera, PoE splitter
or other equipment support IEEE802.3af standard. The injector
supports IEEE802.3af standard that can detect the connected
device, which supports the IEEE802.3af and then provides the
power to the device.
Package content
Before you start installing the device, verify the following items are
in the package:
● SP390BI Injector
● Quick Installation Guide
● Power Cord
Features
● Remote power feeding
● Compliant with IEEE802.3af
● Convey power and data over Ethernet cable
● Short-circuit protection
● Light weight and compact size
● Plug-and-Play
Physical Description
SP390BI view SP390BI view
● DATA IN port: It is a RJ-45 Ethernet interface port for data
transmit to the PoE Injector. It is used to
connect to switch.
● DATA OUT port: It is a RJ-45 Ethernet port and has a fix RJ-45
cable for connecting with the PoE Splitter
(SP390BS).
● POWER IN port: The POWER IN port is for supporting the power
into injector.
PN: 2300-0461
7
5 6
Quick Installation Guide
Power over Ethernet Injector
Model No.: SP390BI
http://www.micronet.info
CE Mark Warning
This equipment complies with the requirements relating to
electromagnetic compatibility, EN 55022 class B for ITE, the
essential protection requirement of Council Directive 89/336/EEC
on the approximation of the laws of the Member States relating to
electromagnetic compatibility.
Company has an on-going policy of upgrading its products and it
may be possible that information in this document is not up-to-date.
Please check with your local distributors for the latest information.
No part of this document can be copied or reproduced in any form
without written consent from the company.
Trademarks:
All trade names and trademarks are the properties of their
respective companies.
Copyright © 2006, All Rights Reserved.
WARNING:
Connect the injector with splitter only. Connecting the injector
directly to other devices may cause serious damage!
Specifications
IEEE802.3, 10BASE -T
IEEE802.3u,100BASE-TX
IEEE802.3af, Power over Ethernet
RJ-45 Data in/out: Data/signal pairs pin 1, 2, 3, 6
RJ-45 Power out: power over spare wire pairs pin:
4, 5(V+) , 7, 8(V-)
0 ° - 40 °C (32 ° - 104° F)
10% - 90% (Non-condensing)
60 x 117 x 35 mm ( W x L x H )
176
Input: 100-240V, 50/60Hz, 0.3A
Output: 40VDC, 0.3A, 15.5Watts
FCC Class B,CE
RJ-45 (10BASE-T): Cat.3, 4, 5 UTP/STP
RJ-45 (100BASE-TX): Cat.5, 5e UTP/STP
Standard
Interface
Cable Connections
Operating Temperature
Operating Humidity
Weight (g)
Power Supply
Emission
Dimension (mm)
  • Page 1 1
  • Page 2 2

MicroNet SP390BI User manual

MicroNet
Brand
MicroNet
Model
SP390BI
Category
Network splitters
Type
User manual
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents