Furuno NAVPILOT 711C/OB-IPS Installation guide

Type
Installation guide
www.furuno.com
NAVpilot-700/711
VOLVO IF KIT FAP-6300
INSTALLATION INSTRUCTIONS
This information provides the instructions for the installation of the VOLVO IF kit. This kit enables
the NAVpilot-700/711 to automatically steer a VOLVO IPS drive equipped vessel whose length is
between 35 and 80 ft.
For the operation and installation of the autopilot, see the operator’s manual (OME-72720) and
installation manual (IME-72720).
Please read these safety instructions before you install or operate the equipment.
Do not use the autopilot in the
following situations:
- Cruising speed is more than 40 kn
- Harbor entrance or narrow channel
- Where vessels change course often,
such as a cape or small island
- Poor visibility areas because of the
fog or rain, etc.
- When the vessel is stopped
IF-700IPS 0.30 m 0.30 m
Do not open the equipment unless
you are well familiar with electrical
circuits.
Only qualified personnel should work
inside the equipment.
WARNING
WARNING
CAUTION
Do not lock the helm when the
autopilot controls the vessel.
Malfunction or accident can result.
Do not speed up suddenly when the
autopilot controls the vessel.
Do not raise the speed to 30-40 kn
within 30 seconds. The autopilot can
not calculate parameters under those
conditions. Malfunction or accident can
result.
When an alarm sounds, switch the
steering mode to the STBY mode
and then control the vessel with the
helm.
Malfunction or accident can result if the
vessel is steered automatically.
For the heading sensor, use the
PG-700.
Use the rate gyro hybrid sensor (PG-700)
for the heading sensor. Install the
PG-700 away from metallic objects,
radiotelephone, and the antenna of a
radiotelephone. Malfunction or accident
can result if the sensor is too close to
those objects.
Do not input the heading data (output
from the autopilot) to the radar, etc.
The heading data output from the
autopilot is delayed for max 1 second
over the input data.
Follow the compass safe distances to
prevent interference to a magnetic
compass.
Standard
Compass
Steering
Compass
2
1. Materials
VOLVO IF Kit (Type: FAP-6300, Code No.: 000-022-971)
2. IPS Interface Unit (IF-700IPS)
2.1 LED status and meaning
The LED on the IPS interface unit indicates the status of the unit.
The LED status and meaning are shown below.
Name Type Code No. Qty Remarks
IPS Interface Unit IF-700IPS - 1
VOLVO IPS Gateway AUTOPILOT-GATEWAY - 1
Cable Assy. MJ-A7SPF0005-020C 000-159-699-10 1 2 m
Self-tapping Screw 4x16 SUS304 000-162-605-10 4
Fuse FGMB 125V 1A PBF 000-157-478-10 1 Spare parts
LED Lamp Status Status/Action
Off The IPS interface unit is OFF. The unit is powered by the processor
unit (FAP-7002). Turn on the processor unit.
Flashes The IPS interface unit operates normally.
Flashes twice, and then
goes off for two seconds
Communication error between the VOLVO IPS gateway and IPS in-
terface unit. Check the connection between the VOLVO IPS gate-
way and IPS interface unit.
LED (green)
IPS interface unit IF-700IPS
3
2.2 Mounting
Mounting considerations
When selecting a location, keep in mind the following points.
Make sure the location is strong enough to support the unit under the conditions of continued
vibration and shock normally encountered on the vessel.
Locate the unit away from heat sources.
The location must not be near water, rain and water splash.
Follow the recommended maintenance space shown in the outline drawing.
Follow the compass safe distance (standard compass: 0.30 m, steering compass: 0.30 m) to
prevent interference to a magnetic compass.
Connect the ground wire between the ground terminal and ship’s earth.
Keep in mind the length of the connection cable between the units.
Procedure
Install the unit with two self-tapping screws, on a bulkhead or desktop.
Self-tapping screw
4
2.3 Wiring
Connect the cable assy. (MJ-A7SPF0005-020C) and VOLVO IPS gateway to the IPS interface
unit as shown below.
Connection with the processor unit FAP-7002
Connect the cable assy. (MJ-A7SPF0005-020C) to TB1 (power) and TB7 (NMEA0183 port 2) of
the processor unit as shown in the procedure which follows.
Ground wire
(IV-1.25sq.)
Cable Assy.
(MJ-A7SPF0005-020C, 2m)
To processor unit FAP-7002
To VOLVO Penta EVC system
VOLVO IPS gateway
IPS interface unit IF-700IPS
TB1
Power
Cable entrance of the processor unit
㪂㩷㩷㩷㩷㪄
㪂㩷㩷㩷㩷㪄
㪂㩷㩷㩷㩷㪄
TB7
NMEA 0183 port 2
Processor unit FAP-7002
5
1. Remove the outside cover of the processor unit; hold the right and left sides of the cover and
pull the cover outward.
2. Remove the four screws circled below.
3. Remove the cable clamp/fan assy. from the shield cover.
Note: When removing the cable clamp/fan assy., be careful not to apply tension to the fan
connector.
4. Disconnect the fan connector.
Outside cover
Cable clamp/fan assy.
Shield cover
Disconnect
this connector.
6
5. Connect the cable assy. (MJ-A7SPF0005-020C) to the connector blocks TB1 and TB7.
Connection with TB1 (power)
Clamp the power line of the cable assy. and power cable of processor unit with the crimping
terminal, and then connect the + line (red) and - line (black) to the TB1 of the processor unit.
For the crimping terminal, use rod terminals or plate shape pre-insulation terminals.
Note1: Do not twist cores.
Note2: The + line (red) has a fuse holder. To prevent the detachment of the fuse, make a loop
in the power line of the cable assy. and then fix the lines as shown below.
Connection with TB7 (NMEA port 2)
Connect the signal lines of the cable assy. to TB7.
6. Fix the cable assy. to the cable clamp with a cable tie (supplied with processor unit).
7. Connect the fan connector.
8. Reattach the cable clamp/fan assy. and outside cover.
1 A fuse holder
(+ line, red)
Fix the lines with a cable tie.
Connector block
Push
Twist
cores.
6 mm
How to put wire into connector block
1. Make length of cores 6 mm.
2. Twist cores.
3. Push spring-loaded catch with slotted-head
screwdriver.
4. Insert core into hole.
5. Release screwdriver.
6. Pull wire to confirm it is securely inserted.
1234
5
5
ColorPin No.
Green
1
2
3
4
5
Yellow
White
Blue
Drain
TB7
Signal
TD_A
TD_B
RD_H
RD_C
Shield
Wind the copper tape around
the cable assy., and then fix to
the cable clamp with a cable tie.
Example: After connecting the cable assy.
TB7
TB1
7
Fuse replacement
The fuse in the fuse holder on the + line (red) of the cable assy. (MJ-A7SPF0005-020C) protects
the IPS interface unit from overcurrent and equipment fault. If you can not turn on the power, check
if the fuse has blown. If the fuse has blown, find the reason before you replace the fuse. If the fuse
blows again after the replacement, contact your dealer for advice.
VOLVO IPS Gateway (AUTOPILOT GATEWAY)
Install the unit with two self-tapping screws.
For details of the installation and wiring, see the installation manual of the VOLVO IPS gateway.
Name Type Code No.
Fuse FGMB 125V 1A PBF 000-157-478-10
WARNING
Use the proper fuse.
Use of a wrong fuse can result in fire and
damage the equipment.
: Minimum service clearance.
Unit mm
130
116
56
10
250
60
20
20.5
5.5
10
8
4. Initial Settings
This section shows you how to select language and units and open the [INSTALLATION] menu.
For details of the settings on the [INSTALLATION] menu, see the installation manual
(IME-72720).
1. Press the POWER/BRILL key or POWER/STBY key to turn on the power.
The first time the system is powered, the language selection menu appears.
2. Rotate the knob to select required language, and then push the knob.
3. Press the X key to show the [UNIT SETUP] menu.
1) Select the item to change then push the knob.
2) Select the unit to use then push the knob.
4. Press the X key to show the [OPERATION MODE] menu.
㪜㪥㪞㪣㪠㪪㪟㩿㪬㪪㪘㪀
㪜㪥㪞㪣㪠㪪㪟
㪝㪩㪘㪥㪚㪘㪠㪪
㪜㪪㪧㪘㪥㪦㪣
㪧㪦㪩㪫㪬㪞㪬㪜㪪
㪛㪜㪬㪫㪪㪚㪟㪜
㪠㪫㪘㪣㪠㪘㪥㪦
㪥㪦㪩㪪㪢
㪛㪘㪥㪪㪢㪜
㪪㪭㪜㪥㪪㪢㪘
㪪㪬㪦㪤㪠
UNITS SETUP
SPEED UNIT: kn
RANGE UNIT: nm
WIND SPEED UNIT: kn
DEPTH UNIT: ft
WATER TEMP UNIT: °F
PREV NEXT
OPERATION MODE
INSTALLATION
DEMO SLIDE SHOW
SIMULATOR
PREV NEXT ENTER
9
5. Select [INSTALLATION] then push the knob to show the [INSTALLATION] menu.
See the installation manual (IME-72720) for how to set the [INSTALLATION] menu.
Note1: The [INSTALLATION] menu can be opened from the STBY display by pressing the
knob three times while pressing and holding down the MENU key.
Note2: Set [BOAT TYPE] to [VOLVO EVC BOAT] on the [SHIP’S CHARACTERISTICS]
menu to use the VOLVO interface kit.
Check points before cruising
Check the following points before cruising.
Confirm that no error message appears.
When the IPS drive controls the rudder, the OVRD (override) mode is automatically enabled.
The rudder turns according to the W and X key in the AUTO mode.
INSTALLATION MENU
LANGUAGE: ENGLISH
UNITS SETUP
DISPLAY SETUP
SHIP’S CHARACTERISTICS
CAN BUS SETUP
NMEA0183 SETUP
SENSOR SELECTION
UNIVERSAL PORT
SEA TRIAL
COMPASS CALIBRATION: NO
1
,
2
DATA CALIBRATION
PARAMETER SETUP
AUTO OPTION
NAV OPTION
INSTALLATION MENU
FISH HUNTER OPTION
SYSTEM SETUP
RC SETUP
ALARM
Page 1 Page 2
1
: NO is replaced with DONE when
respective setup is completed.
NAVpilot-700 INSTALLATION menu
( BOAT TYPE VOLVO EVC BOAT )
2
: Shown when PG-700 is connected.
10
5. OVRD Mode
When the IPS drive controls the rudder, the OVRD (override) mode is automatically enabled. The
autopilot can not control the vessel in the OVRD mode.
Note: The OVRD mode is enabled when [BOAT TYPE] is set to [VOLVO EVC BOAT].
OVRD mode activation in the STBY mode
When the OVRD mode activates in the STBY mode, [OVRD] appears at the top-left position of the
display. At this time only the [INSTALLATION] and user menus are operative. When the IPS drive
releases control of the rudder, the autopilot goes to the STBY mode.
OVRD mode activation in the AUTO or NAV mode
When the OVRD mode activates in the AUTO or NAV mode, the audio alarm sounds, the pop-up
[EVC OVERRIDE] appears, and the mode indication at the top-left position of the display shows
[OVRD]. Press any key to stop the alarm and erase the pop-up. When the IPS drive releases con-
trol of the rudder, the autopilot goes to the STBY mode.
A
UTO
65
SETCSE
HDG
M
68.0
DEVIATION
3
20 10 5 5 10 20
㪭㪩㪛
㪩㪬㪛㪛㪜㪩
65
SETCSE
HDG
M
68.0
DEVIATION
3
20 10 5 5 10 20
㪩㪬㪛㪛㪜㪩
㪫㪙㪰
When the IPS drive releases
control of the rudder.
A
UTO
65
SETCSE
HDG
M
68.0
DEVIATION
3
20 10 5 510 20
㪭㪩㪛
㪩㪬㪛㪛㪜㪩
㪜㪭㪚㩷㪦㪭㪜㪩㪩㪠㪛㪜
A
UTO
65
SETCSE
HDG
M
68.0
DEVIATION
3
20 10 5 5 10 20
㪭㪩㪛
㪩㪬㪛㪛㪜㪩
65
SETCSE
HDG
M
68.0
DEVIATION
3
20 10 5 5 10 20
㪩㪬㪛㪛㪜㪩
㪫㪙㪰
Press any key.
When the IPS drive releases
control of the rudder
11
6. Messages
The massages which may appear when the [BOAT TYPE] is set to [VOLVO EVC BOAT] are
shown below.
When the system detects an alarm violation, error, etc., the alarm sounds and a message appears
on the display. Press the any key to stop the alarm and delete the message.
Message Status/Action
EVC INTERFACE ERROR Communication error between the processor unit and IPS inter-
face unit. Check the connection between the processor unit and
IPS interface unit.
NO CONTACT WITH EVC. Communication error between the VOLVO IPS gateway and IPS
interface unit occurs. Check the connection between the VOLVO
IPS gateway and IPS interface unit. Also check the connection
between the VOLVO IPS gateway and VOLVO Penta EVC sys-
tem.
EVC INTERFACE FAIL.
PLEASE TURN OFF AND
CHECK EVC INTERFACE.
System error of the IPS interface unit. Turn off the autopilot, con-
tact your dealer.
EVC OVERRIDE The OVRD mode is enabled.
EVC INTERFACE HAS
FAILED STARTUP TEST.
PLEASE CONTACT A LO-
CAL FURUNO REPRE-
SENTATIVE FOR REPAIR.
This message appears for the result of the startup test.
System error of the IPS interface unit. Turn off the autopilot, con-
tact your dealer.
NO CONNECT EVC INTER
FACE. PUSH ANY KEY TO
CONTINUE.
This message appears for the result of the startup test.
The IPS interface unit is not connected. Check the connection be-
tween the processor unit and IPS interface unit.
/CT
;0+5*+;#/#
D-1
 
$
#
&
%
0#/'
ฬ⒓
6+6.'
MI
/#55
&9) 0Q
5%#.'
#22418'&
%*'%-'&
&4#90
4'(0Q
+06'4%100'%6+10 &+#)4#/
⋧੕⚿✢࿑
ࠝ࡯࠻ࡄࠗࡠ࠶࠻
#7612+.16
0#8RKNQV
 126+10
 5*+2;#4& 5722.;
016'
㧖㧞㧕ࠝࡊ࡚ࠪࡦޕ
㧖㧝㧕ㅧ⦁ᚲᚻ㈩ޕ
ᵈ⸥
㧖㧟㧕ࠤ࡯ࡉ࡞㐳ߐߦࠃࠅ⧌✢ߩᄥߐࠍᄌᦝߔࠆޕ
 %*#0)' 6*' %14' 5+<' #%%14&+0) 61 %#$.' .'0)6*
6;#/#5#-+
*/#-+
5*+'.&
)0&
9*6
$.7
;'.
)40
4'&
$.-
ࠪࡠ
ࠕࠝ
㩚㩎㩨㩢
ࠕࠞ
ࠢࡠ
)0&
%10641. #
5*+'.&
)0&
9*6
$.7
;'.
)40
4'&
$.-
ࠪࡠ
ࠕࠝ
㩚㩎㩨㩢
ࠕࠞ
ࠢࡠ
%10641. $
,
5*+'.&
)0&
$.7
;'.
)40
ࠕࠝ
㩚㩎㩨㩢
4'&ࠕࠞ
࠴ࡖ $40
4'/2
4'/5+)
4'/0
4'/59
4475+)
447A5+)
5*+'.&
)40㩚㩎㩨㩢
;'.
ࠢࡠ
ࠪࡠ 9*6
$.-
447
,
,
%10641. 70+6
ᠲ૞ㇱ
,
,
)0&
O (#2
4'/16' %10641..'4
㆙㓒▤೙ེ
47&&'4 4'('4'0%'
ㅊᓥ⊒ାེ
70+6 (#2
ห਄
&+661
6'4/+0#614
⚳┵ེ
,
%10641. 70+6
ᠲ૞ㇱ
OǾ
5*+'.&
)0&
4'/16' %10641..'4
(#2
㆙㓒▤೙ེ
4'/16' %10641..'4
㆙㓒▤೙ེ
4'/16' %10641..'4
㆙㓒▤೙ེ
(#2 (#2
ᠲ૞ㇱᠲ૞ㇱ %10641. 70+6%10641. 70+6

+8US

+8US

+8US
4'/2
4'/5+)
4'/0
4'/59
(#2 (#2
,
(#2
(#2
6$


8&%
219'4
%#0 DWU
6$
5*+'.&
$&#((/
219'4A59
%#0A*
%#0A.
8A2
$&#((/
.4
OǾ
$&#((/
$&#((/.4OǾ
$&#((/.4OǾ
6$
6$
0'6A5
0'6A%
0'6A*
0'6A.
0'6 219'4
6$
0'6A5
0'6A%
5*+'.&

+8US
8$75
&A2
&A0
)0&
75$
8$75
&A2
&A0
)0&
75$
75$ %#$.'
6$



4'/ 
447A294
)0&
)0&
8A2
219'4A59
%#0A*
%#0A.
4'/16' %10641..'4
㆙㓒▤೙ེ
(#2
4'/16' %10641..'4
(#2
㆙㓒▤೙ེ
/,#52(OǾ

/,#52(
,

/,#52(
4'/2
4'/5+)
4'/0
4'/59
4'/%1/
0%
0%
0%
0%
()
4'/2
4'/5+)
4'/0
4'/59
4'/%1/
0%
0%
0%
0%
()
ࠕࠝ
㩚㩎㩨㩢
࠴ࡖ
ࠕࠞ
$.7
;'.
)40
4'&
$40

294A59A*
294A59A%
%#0A*
%#0A.
8
5*+'.&
)0&
294A59A*
294A59A%
%#0A*
%#0A.
8
5*+'.&
)0&
294A59A*
294A59A%
%#0A*
%#0A.
8
5*+'.&
)0&
294A59A*
294A59A%
%#0A*
%#0A.
8
5*+'.&
)0&
294A59A*
294A59A%
%#0A*
%#0A.
8
5*+'.&
)0&
294A59A*
294A59A%
%#0A*
%#0A.
8
5*+'.&
(#2
&+564+$7614
ಽ㈩ེ


 

 


,
,
/,#52(
/,#52(
,
ห਄
&+661
O
2%
ࡄ࠰ࠦࡦ
ࡔࡦ࠹࠽ࡦࠬ↪
(14 /#+06'0#0%' 10.;
%10641. 70+6
ᠲ૞ㇱ
(#2
(#2

,70%6+10 $1:
ࠤ࡯ࡉ࡞ᑧ㐳
࡙࠾࠶࠻
$&#((/
,

$&#(#(.4
OǾ

$&#(#(.4
OǾ
㩒㨹㩎㩦㨺㩂㩍㩨㩔㩨㨼㩇
0'6914- &'8+%'
6$





㧔ㆬᛯ㧕
㧔5'.'%6㧕
)0&
51.$/1614
51.#/1614
6$
51.#
51.$
51.%1/
51.'01+& 8#.8'
㔚⏛ᑯ
4'8'45+$.' 27/2
࡝ࡃ࡯ࠪࡉ࡞ࡐࡦࡊ
/1614#
/1614$
241%'5514 70+6
೙ᓮㇱ
(#2
6$
$%A219'4
$%
5*+'.&
/1614
/1614
$;2#55%.76%*
$;2#55%.76%*
$%
*;&4#7.+% .+0'4
&4+8'
ࠢ࡜࠶࠴
/161451.
5*+'.&
6&#
6&$
4&*
4&%
2
2
0/'# 2146
6$
5*+'.&
6$
)'0'4#. 176
176A01
%1/
176A0%
176A01
%1/
176A0%
4'.#; %106#%6 /#:#
ᄖㇱࠕ࡜࡯ࡓ
':6'40#. #.#4/
ᄖㇱࠕ࡜࡯ࡓ
':6'40#. #.#4/
ାภߩ⒳㘃ߦࠃࠅធ⛯ࠍㆬᛯߔࠆ
%100'%6+10 5'.'%6'& $; 5+)0#. /1&'
)'0'4#. +0
6$
59A8
59A+0
59A)0&
59A8
59A+0
59A)0&

ࠗࡌࡦ࠻ࠬࠗ࠶࠴
'8'06 59+6%*
*'./ 5'0514
*'./ 5'0514
*'./ 5'0514A5+)
*'./ 5'0514
*'./ 5'0514A5+)
*'./ 5'0514
 
&2;/#:#
&2;
 
&2;
 
#66#%*'&
/1614#
/1614$
ࡄࡢ࡯ࠕࠪࠬ࠻ࠪࠬ࠹ࡓ
#%%756''4 (25
$40࠴ࡖ
ࠢࡠ
ࠕࠝ
$.-
$.7
$40࠴ࡖ
ࠢࡠ
ࠕࠝ
$.-
$.7
ࠢࡠ $.-
ࠕࠞ 4'&
%#$.'O
0%
5*+'.&
6:&*
6:&%
4:&*
4:&%
⥶ᴺⵝ⟎
0#8 '37+2/'06
߹ߚߪ 14
*'#&+0) 5'05140/'#
/,#52(OǾ

;'.
)40
㩚㩎㩨㩢
9*6ࠪࡠ
ࠢࡠ $.-
㩗㩍㩨㨲㩧㩂㩨㩈㩧㩅㨺
5*+'.&
6$
6&#
6&$
4&*
4&%
2
0/'# 2146
2
+(+25
+25ធ⛯࡙࠾࠶࠻
+25 +06'4(#%' 70+6

+8US
#
;'.
)40
㩚㩎㩨㩢
9*6ࠪࡠ
ࠕࠝ $.7
ࠢࡠ $.-
ࠕࠞ 4'&
/$((/O

%$$((/O
ࠕࠞ 4'&
ࠢࡠ $.-
ࠪࡠ 9*6
ࠕࠝ $.7
 1// .
6'4/+0#614
⚳┵ེ


219'4 5722.;
 8&%
8%6(Z% 
/CT
/CT
%% , 
/2;
/,#52(%O
81.81 +06'4(#%' -+6
81.81ࠗࡦ࠲࡯ࡈࠚࠗࠬࠠ࠶࠻
(#2
&2;
 
 8&%
 
62;

O
81.81 +25 )#6'9#;
#7612+.16 )#6'9#;
81.81 +25ࠥ࡯࠻࠙ࠚࠗ
81.81 +25

/CT;0+5*+;#/#
Yoshihir
o
Nishiya
ma
:Yoshihiro NishiyamD
DN:cn=Yoshihiro Nishiyama, c=JP - , o=FURUNO
ELECTRIC Co., Ltd., ou=Technical Documentation
:2013.03.19 08:53:50 +09'00
S-1
11
㪍㪅㩷
㪲㪙㪦㪘㪫㩷㪫㪰㪧㪜㪴 㪲㪭㪦㪣㪭㪦㩷㪜㪭㪚㩷㪙㪦㪘㪫㪴 ⊒↢䈜 ਅ⴫䈮⸥タ 䈜䇯
䊤䊷䊛䉣䊤䊷↢䈚䈢 䈐䈲 䊤䊷䊛 䊒䉝 䉳䈏
䈘䉏 䈚䈩 䉝䊤䊷䊘䉾䊒䉝䉾䊒 䉾䉶䈚䈩
䈒䈣
⁁ᘒ ಣℂ
EVC INTERFACE ERROR
೙ᓮㇱ -IPS ធ⛯࡙࠾࠶࠻㑆ߩㅢାਇ⦟߇⊒↢ߒߡ޿߹ߔޕ೙
ᓮㇱ -IPS ធ⛯࡙࠾࠶࠻㑆ߩធ⛯ࠍ⏕⹺ߒߡߊߛߐ޿ޕ
NO CONTACT WITH EVC.
IPSធ⛯࡙࠾࠶࠻-VOLVO IPSࠥ࡯࠻࠙ࠚࠗ㑆ߩㅢାਇ⦟߇⊒↢
ߒߡ޿߹ߔޕIPS ធ⛯࡙࠾࠶࠻ -VOLVO IPS ࠥ࡯࠻࠙ࠚࠗ㑆ߩ
ធ⛯ޔ߅ࠃ߮ VOLVO IPS ࠥ࡯࠻࠙ࠚࠗ -VOLVO Penta EVC
ࠬ࠹ࡓ㑆ߩធ⛯ࠍ⏕⹺ߒߡߊߛߐ޿ޕ
EVC INTERFACE FAIL.
PLEASE TURN OFF AND
CHECK EVC INTERFACE.
IPS ធ⛯࡙࠾࠶࠻ߦ⇣Ᏹ߇⊒↢ߒߡ޿߹ߔޕᧄᯏߩ㔚Ḯࠍಾࠅޔ
ᒰ␠߹ߚߪઍℂᐫߦ߅໧޿วࠊߖߊߛߐ޿ޕ
EVC OVERRIDE
ࠝ࡯ࡃ࡯࡜ࠗ࠼ࡕ࡯࠼ߦ⒖ⴕߒߚߎߣࠍ⍮ࠄߖࠆㅢ⍮ޕ
EVC INTERFACE HAS
FAILED STARTUP TEST.
PLEASE CONTACT A LO-
CAL FURUNO REPRE-
SENTATIVE FOR REPAIR
⿠േᤨߩࠬ࠲࡯࠻ࠕ࠶ࡊ࠹ࠬ࠻ߩ⚿ᨐߣߒߡ⴫␜ߐࠇ߹ߔޕ
IPS ធ⛯࡙࠾࠶࠻ߦ⇣Ᏹ߇⊒↢ߒߡ޿߹ߔޕᧄᯏߩ㔚Ḯࠍಾࠅޔ
ᒰ␠߹ߚߪઍℂᐫߦ߅໧޿วࠊߖߊߛߐ޿ޕ
NO CONNECT EVC IN-
TERFACE. PUSH ANY
KEY TO CONTINUE
⿠േᤨߩࠬ࠲࡯࠻ࠕ࠶ࡊ࠹ࠬ࠻ߩ⚿ᨐߣߒߡ⴫␜ߐࠇ߹ߔޕ
IPS ធ⛯࡙࠾࠶࠻߇ធ⛯ߐࠇߡ޿߹ߖࠎޕ೙ᓮㇱ -IPS ធ⛯࡙
࠾࠶࠻㑆ߩធ⛯ࠍ⏕⹺ߒߡߊߛߐ޿ޕ
10
㪌㪅㩷
㪠㪧㪪 ⥽ᯏ೙ᓮਛ䇮 䈲⥄േ⊛䈮䊋䊷 䈮ಾ
䈜䇯 䉥䊷䊋䊷 䊝䊷 ਛ䈲䇮 䉥䊷 േᠲ೑↪䈜 䈲䈪
䈐䉁
ᵈ㧕ࠝ࡯ࡃ࡯࡜ࠗ࠼ࡕ࡯࠼ߪޔ[BOAT TYPE] [VOLVO EVC BOAT] ࠍ⸳ቯߒߡ޿ࠆ႐วߩߺ
೑↪น⢻ߢߔޕ
ᚻേ ᤨ䈱䊋䊷
ᚻേ䊝䊷 䊷䊋 ⒖ⴕ ↹㕙Ꮐ਄ ⴫␜ 㪲㪦㪭㪩㪛㪴
䈜䇯 㪲㪠㪥㪪㪫㪘㪣㪣㪘㪫㪠㪦㪥㩷㪤㪜㪥㪬㪴 䉱䊷 䊷એᄖᯏ⢻䈲೑↪
㪠㪧㪪 ⥽ᯏ೙ᓮ⸃㒰 䊷䊋 ⸃㒰
⥄േ⊛䈮ᚻേ䊝䊷 䈮ಾ ᦧ䉒 䈜䇯
⥄േ ⥶ᴺ ᤨ䈱䊋䊷
⥄േ ⥶ᴺ 䉥䊷䊋䊷 ⒖ⴕ 㖸䈍
㪲㪜㪭㪚㩷㪦㪭㪜㪩㪩㪠㪛㪜㪴 䈏⴫␜ 䉏䇮 ↹㕙Ꮐ਄ ⴫␜䈏 㪲㪦㪭㪩㪛㪴 䈮ಾ 䈜䇯 䈇䈝
䈱䉨䊷䉕᛼䈩䇮 䊷䊛㖸䈍䉋䈶䊘 䉕ᶖ
䈱⹺⍮ᓟ 㪠㪧㪪 ⥽ᯏ೙ᓮ䈏⸃㒰 䉥䊷䊋䊷 䊝䊷 䈲⸃㒰
䉏⥄േ⊛䈮ᚻേ䊝䊷 䈮ಾ ᦧ䉒 䈜䇯
A
UTO
65
SETCSE
HDG
M
68.0
DEVIATION
3
20 10 5 5 10 20
㪭㪩㪛
㪩㪬㪛㪛㪜㪩
65
SETCSE
HDG
M
68.0
DEVIATION
3
20 10 5 5 10 20
㪩㪬㪛㪛㪜㪩
㪫㪙㪰
㪠㪧㪪 䊄䊤䉟䊑䈮䉋䉎
⥽ᯏ೙ᓮ䉕⸃㒰
A
UTO
65
SETCSE
HDG
M
68.0
DEVIATION
3
20 10 5 510 20
㪭㪩㪛
㪩㪬㪛㪛㪜㪩
㪜㪭㪚㩷㪦㪭㪜㪩㪩㪠㪛㪜
A
UTO
65
SETCSE
HDG
M
68.0
DEVIATION
3
20 10 5 510 20
㪭㪩㪛
㪩㪬㪛㪛㪜㪩
䈇䈝䉏䈎䈱
䉨䊷䉕᛼䈜
65
SETCSE
HDG
M
68.0
DEVIATION
3
20 10 5 510 20
㪩㪬㪛㪛㪜㪩
㪫㪙㪰
㪠㪧㪪 䊄䊤䉟䊑䈮䉋䉎
⥽ᯏ೙ᓮ䉕⸃㒰
9
㪌㪅㩷 㪲㪠㪥㪪㪫㪘㪣㪣㪘㪫㪠㪦㪥㪴 ㆬᛯ ᠲ૞ 䈜䇯
㪲㪠㪥㪪㪫㪘㪣㪣㪘㪫㪠㪦㪥㪴 ⴫␜ 䈜䇯 㪲㪠㪥㪪㪫㪘㪣㪣㪘㪫㪠㪦㪥㪴 䈱⸳ቯ
䈲䇮 ⵝ஻ⷐ㗔ᦠ 䋨㪠㪤㪡㪄㪎㪉㪎㪉㪇䋩 ෳᾖ
1ᚻേࡕ࡯࠼ᤨߦ [MENU] ࠠ࡯ࠍ᛼ߒߥ߇ࠄᠲ૞ࡁࡉࠍ 3 ࿁᛼ߔߣޔ[INSTALLATION]
ࡔ࠾ࡘ࡯ࠍ㐿ߊߎߣ߇ߢ߈߹ߔޕ
2 VOLVO ࠗࡦ࠲࡯ࡈࠚࠗࠬࠠ࠶࠻ࠍ೑↪ߔࠆ႐วߪޔ[SHIP’S CHARACTERISTICS]
ࡔ࠾ࡘ࡯਄ߢ [BOAT TYPE] [VOLVO EVC BOAT] ߦ⸳ቯߒߡߊߛߐ޿ޕ
૶↪೨䈱ὐᬌ
ᧄᯏ೑↪䈜 ೨䈮 ਅ⸥䈱⏕⹺
䊷䉳䈏䉏䈭䈇
㪠㪧㪪 ⥽ᯏ೙ᓮᤨ䈮 ⥄േ⊛䊋䊷 䈮⒖ⴕ
䈜䉎
䍃⥄W 䈍䉋䈶 X 䈢ᣇะ䈮⥽䈏േ
INSTALLATION MENU
LANGUAGE: ENGLISH
UNITS SETUP
DISPLAY SETUP
SHIP’S CHARACTERISTICS
CAN BUS SETUP
NMEA0183 SETUP
SENSOR SELECTION
UNIVERSAL PORT
SEA TRIAL
COMPASS CALIBRATION: NO*
1
,
*
2
DATA CALIBRATION
PARAMETER SETUP
AUTO OPTION
NAV OPTION
INSTALLATION MENU
FISH HUNTER OPTION
SYSTEM SETUP
RC SETUP
ALARM
1 2
*
1
ᣇ૏䉶䊮䉰䊷䈱⵬ᱜቢੌᓟ䇮䇸㪥㪦䇹䈱
⴫␜䈲䇸㪛㪦㪥㪜䇹䈮ᄌ䉒䉍䉁䈜䇯
㪲㪙㪦㪘㪫㩷㪫㪰㪧㪜㪴㪔㪲㪭㪦㪣㪭㪦㩷㪜㪭㪚㩷㪙㪦㪘㪫㪴䈱䈫䈐䈱㪲㪠㪥㪪㪫㪘㪣㪣㪘㪫㪠㪦㪥㩷㪤㪜㪥㪬㪴
䋨㪝㪘㪧㪄㪎㪇㪇㪈䈱႐ว䈱⴫␜଀䋩
*
2
㪧㪞㪄㪎㪇㪇ធ⛯ᤨ䈮⴫␜䈘䉏䉁䈜䇯
8
㪋㪅㩷 ⵝ஻ᓟ䈱⸳ቯ
ೋ࿁⿠േᤨ䈱⸒⺆ න૏⸳ቯ䇮 㪲㪠㪥㪪㪫㪘㪣㪣㪘㪫㪠㪦㪥㪴 䈱⴫␜ᣇᴺ䈮⸥タ
䈜䇯 㪲㪠㪥㪪㪫㪘㪣㪣㪘㪫㪠㪦㪥㪴 䊷䈪⸳ቯ䈧䈇 ⵝ஻ⷐ㗔ᦠ 䋨㪠㪤㪡㪄㪎㪉㪎㪉㪇䋩 ෳᾖ
䈘䈇
㪈㪅㩷 ᠲ૞ㇱ䈱 㪲㪧㪦㪮㪜㪩㪆㪙㪩㪠㪣㪣㪴 㪲㪧㪦㪮㪜㪩㪆㪪㪫㪙㪰㪴 䉨䊷ࠍ᛼ߒߡޔ㔚Ḯࠍ౉ࠇ߹ߔޕ
ೋ࿁⿠േᤨߪޔਅ࿑ߩࠃ߁ߥ⸒⺆⸳ቯࡔ࠾ࡘ࡯߇⴫␜ߐࠇ߹ߔޕ
㪉㪅㩷 ૶↪䈜⸒⺆ㆬᛯ ᠲ૞ 䈜䇯
㪊㪅㩷 X 䊷䉕᛼䈚䈩䇮 䊷䉕㐿䈐䉁䈜
ᦝ䈚䈢䈇ᛯ䈚䇮 䊑䉕᛼䈚䉁䈜
㪉㪀㩷૶↪䈜න૏ㆬᛯ ᠲ૞ 䈜䇯
㪋㪅㩷 X㪴䉨
㪜㪥㪞㪣㪠㪪㪟㩿㪬㪪㪘㪀
㪜㪥㪞㪣㪠㪪㪟
㪝㪩㪘㪥㪚㪘㪠㪪
㪜㪪㪧㪘㪥㪦㪣
㪧㪦㪩㪫㪬㪞㪬㪜㪪
㪛㪜㪬㪫㪪㪚㪟㪜
㪠㪫㪘㪣㪠㪘㪥㪦
㪥㪦㪩㪪㪢
㪛㪘㪥㪪㪢㪜
㪪㪭㪜㪥㪪㪢㪘
㪪㪬㪦㪤㪠
UNITS SETUP
SPEED UNIT: kn
RANGE UNIT: nm
WIND SPEED UNIT: kn
DEPTH UNIT: ft
WATER TEMP UNIT: °F
PREV NEXT
OPERATION MODE
INSTALLATION
DEMO SLIDE SHOW
SIMULATOR
PREV NEXT ENTER
7
䉵䈱੤឵
ᡰ⛎䈱⚵ຠ 㪤㪡㪄㪘㪎㪪㪧㪝㪇㪇㪇㪌㪄㪇㪉㪇㪚 䋨⿒䋩 䈲䇮 ㆊ㔚ᵹ䉇ㆊ㔚࿶
㪠㪧 ⛯䊡 䈱᡿㓚 䈏ઃ䈇䈜䇯 ᧄᯏ䈱㔚Ḯ䈏౉ 䈲䇮
䊍䊠 䊍䊠
㔚࿶䈱ේ࿃⸃᳿ ⷙቯ ੤឵ ੤឵ᓟ䈮ౣ䈶 ಾ䉏
䈲䇮 ᒰ␠ 䈲ઍℂᐫ䈍໧ว䈞
㪊㪅㩷 㪭㪦㪣㪭㪦㩷㪠㪧㪪 䋨㪘㪬㪫㪦㪧㪠㪣㪦㪫㪄㪞㪘㪫㪜㪮㪘㪰䋩
ᧄ䉕૶䈦䈩䇮 䉕࿕ 䉁䈜
㪭㪦㪣㪭㪦㩷㪠㪧㪪 䉭䊷 ⵝ஻ ⚿✢⹦⚦䈮䈧䈲䇮 㪭㪦㪣㪭㪦㩷㪠㪧㪪 䈮ઃዻ
ขᛒ⺑᣿ᦠෳᾖ 䈇䇯
ฬ⒓ ဳᑼ ⇟ภ
ࡅࡘ࡯࠭
FGMB 125V 1A PBF 000-157-478-10
䊍䊠䊷䉵䈲ⷙቯ䈱䉅䈱䉕૶↪䈜䉎䈖䈫䇯
ⷙቯᄖ䈱䉅䈱䉕૶↪䈚䈢႐ว䇮 ㊀ᄢ䈭
੐᡿䉇Ἣἴ䉕ᒁ䈐⿠䈖䈜ේ࿃䈮䈭䉍䉁䈜䇯
㪈㪊㪇
㪈㪈㪍
㪌㪍
㩺㪈㪇
㩺㪈㪇
㩺㪉㪌㪇
㩺㪍㪇
㩺㪉㪇
㪉㪇㪅㪌
㩺ශኸᴺ䈲䇮ᦨዊ䉰䊷䊎䉴ⓨ㑆ኸᴺ䈫䈜䉎䇯
න૏䋨㫄㫄䋩
㪌㪅㪌
6
㪌㪅㩷 㪫㪙㪈 㪫㪙㪎 䊦⚵ຠ 㪤㪡㪄㪘㪎㪪㪧㪝㪇㪇㪇㪌㪄㪇㪉㪇㪚 䈱⧌✢
⛯䈚䉁䈜
㪈䋨䋩䈻
䊤䉟䊮 䊤䉟䊮 䈚䉁
⛯䈜 ᫔⁁ 䈲᧼⁁࿶⌕┵ሶ ೙ᓮㇱ㔚Ḯ ࿶⌕
ធ⛯
1ᛮߌ㒐ᱛߩߚ߼ޔࠤ࡯ࡉ࡞⚵ຠߩ㔚Ḯ✢ߣ೙ᓮㇱߩ㔚Ḯࠤ࡯ࡉ࡞ࠍᝦߞߚ⁁ᘒߢធ
⛯ߒߥ޿ߢߊߛߐ޿ޕ
2䊦⚵ຠ + ࡜ࠗࡦ㧔⿒㧕ߦߪޔࡅࡘ࡯࠭ࡎ࡞࠳࡯߇ขࠅઃߌࠄࠇߡ޿߹ߔޕ
ࡅࡘ࡯࠭ࡎ࡞࠳࡯߇ᄖࠇߡធ⸅ਇ⦟߇⿠ߎࠄߥ޿ࠃ߁ߦޔ- ࡜ࠗࡦ㧔㤥㧕ߣ౒ߦࠤ࡯
ࡉ࡞ࠍ৻Ꮞ߈ߒߡ߆ࠄਅ࿑ߩ૏⟎ࠍࠦࡦࡌ࠶ࠢࠬߢ࿕ቯߒߡߊߛߐ޿ޕ
㪫㪙
㪥㪤㪜㪘㩷㪇㪈㪏㪊 䊘䊷 䋩䈻
㪫㪙㪎 䊦⚵ຠ䈱ାภ ធ⛯ 䈜䇯
㪍㪅㩷 䋨೙ᓮㇱ䈱Ꮏ᧚䋩 䊦⚵ຠ 䈮࿕ቯ
䉁䈜
㪎㪅㩷 ㄟ䉂䈜䇯
㪏㪅㩷 䉬 ⚵ຠ䇮 䈶೙ᓮㇱర䈱 䈜䇯
㪈㪘㩷䊍䊠䊷䉵䊖䊦䉻䊷
㩿㪂䊤䉟䊮㪀
䈖䈱ㇱಽ䉕䉮䊮䊔䉾䉪䉴䈪
࿕ቯ䈜䉎䇯
䉮䊈䉪䉺䊑䊨䉾䉪
᛼䈜
⧌✢䉕
ᝦ䉎䇯
㪍㫄㫄
䉮䊈䉪䉺䊑䊨䉾䉪䈻䈱ធ⛯ᣇᴺ
㪈㪅㩷⧌✢䈏㪍㫄㫄䈮䈭䉎䉋䈉䈮䉦䉾䊃䈚䉁䈜䇯
㪉㪅㩷⧌✢䉕ᝦ䉍䉁䈜䇯
㪊㪅㩷䊙䉟䊅䉴䊄䊤䉟䊋䊷䈪䇮䉬䊷䊑䊦ⓣ䈱਄ㇱ䈮䈅䉎
㩷㩷㩷䊗䉺䊮䋨䊋䊈ᑼ䋩䉕᛼䈚䉁䈜䇯
㪋㪅㩷䉬䊷䊑䊦ⓣ䈮⧌✢䉕Ꮕ䈚ㄟ䉂䉁䈜䇯
㪌㪅㩷䊗䉺䊮䈎䉌䇮䊙䉟䊅䉴䊄䊤䉟䊋䊷䉕ᄖ䈚䉁䈜䇯
㪍㪅㩷⧌✢䉕ᒁ䈦ᒛ䈦䈩䇮ᛮ䈔䈭䈇䈖䈫䉕⏕⹺䈚䉁䈜䇯
㪈㪉
✢⦡䊏䊮⇟ภ
䊄䊧䉟䊮✢
㪫㪙㪎
ାภ
㪫㪛㪶㪘
㪫㪛㪶㪙
㪩㪛㪶㪟
㪩㪛㪶㪚
㪪㪿㫀㪼㫃㪻
䉬䊷䊑䊦⚵ຠធ⛯ᓟ䈱઀਄䈏䉍଀
䉬䊷䊑䊦⚵ຠ䈮㌃䊁䊷䊒䉕Ꮞ䈐䇮
䉮䊮䊔䉾䉪䉴䉕૶䈦䈩䉬䊷䊑䊦
䉪䊤䊮䊒䈮࿕ቯ䈜䉎䇯
㪫㪙㪎
㪫㪙㪈
5
㪈㪅㩷 ೙ᓮㇱ
೙ᓮㇱ䊋䊷 ᄖ䈜 Ꮐฝਔ஥ᐩㇱᜰవ ਔ஥䈮ᐢ
䈮䈚䈩䉁䈜
㪉㪅㩷 ਅ࿑䈱૏⟎ 㩿㪋 䈜䇯
㪊㪅㩷 䉲䊷䊦 䊋䊷䈎䉬䊷 ⚵ຠ 䈜䇯
ᵈ㧕ࠤ࡯ࡉ࡞ࠢ࡜ࡦࡊ / ࡈࠔࡦ⚵ຠࠍขࠅᄖߔߣ߈ߪޔࡈࠔࡦ↪ࠦࡀࠢ࠲ߦ⽶⩄߇߆߆ࠄ
ߥ޿ࠃ߁ߦᵈᗧߒߡߊߛߐ޿ޕ
㪋㪅㩷
೙ᓮㇱ䉦䊋䊷
䉬䊷䊑䊦䉪䊤䊮䊒 䊐䉜䊮⚵ຠ
䉲䊷䊦䊄䉦䊋䊷
䈖䈱䉮䊈䉪䉺䉕ᄖ䈜䇯
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24

Furuno NAVPILOT 711C/OB-IPS Installation guide

Type
Installation guide

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI