Fujifilm FINEPIX 2600 ZOOM User manual

Brand: Fujifilm

Model: FINEPIX 2600 ZOOM

Type: User manual

WARNING

THE COMPORNENTS IDENTIFIED BY THE MARK “ “ ON THE SCHEMATHIC

DIAGRAM AND IN THE PARTS LIST ARE CRITICAL FOR SAFETY.

PLEASE REPLACE ONLY BY THE COMPORNENTS SPECIFIED ON THE SCHMATHIC

DIAGRAMAND IN THE PARTS LIST.

IF YOU USE WITH PART NUMBER UN-SPECIFIED, IT MAY RESULT IN A FIRE AND AN

ELECTORICAL SHOCK.

FUJI PHOTO FILM CO.,LTD.

Ref.No.:ZM00377-102

Printed in Japan 2001.08(T.S.)

U/E/EG-Model

SERVICE GUIDE

FinePix 2600Zoom

DIGITAL CAMERA

6. Make leakage - current measurements to determine

that exposed parts are acceptably insulated from the

supply circuit before returning the product to the customer.

7. CAUTION: FOR CONTINUED

PROTECTION AGAINST FIRE

HAZARD, REPLACE ONLY WITH

SAME TYPE 2.5 AMPERES 125V

FUSE.

ATTENTION: AFIN D'ASSURER

UNE PROTECTION

PERMANENTE CONTRE LES

RISQUES D'INCENDIE,

REMPLACER UNIQUEMENT

PAR UN FUSIBLE DE MEME,

TYPE 2.5 AMPERES, 125

VOLTS.

WARNING:

TO REDUCE THE ELECTRIC

SHOCK, BE CAREFUL TO

TOUCH THE PARTS.

2.5A125V

RISK OF FIRE-

REPLACE FUSE

AS MARKED

WARNING!

HIGH VOLTAGE

SAFETY CHECK-OUT

After correcting the original problem, perform the following safety

check before return the product to the costomer.

FinePix2600Zoom(U)Service Guide

1. Check the area of your repair for unsoldered or poorly

sol dered connections. Check the entire board sur

face for solder splasher and bridges.

2. Check the interboard wiring to ensure that no wires

are ÒpinchedÓ or contact high-wattage resistors.

3. Look for unauthorized replacement parts, particu

larly tran sistors, that were installed during a previ

ous repair. Point them out to the customer and rec

ommend their replacement.

4. Look for parts which, though functioning, show obvi

ous signs of deterioration. Point them out to the cus

tomer and recommend their replacement.

5. Check the B + voltage to see it is at the values specified.

FinePix2600Zoom (U/E/EG) SERVICE GUIDE

TABLE OF CONTENTS

Page

1. Specifications

1-1.Product Specifications ............................................................................................................................. 4

2. Names of Components

2-1.Names of External Components .............................................................................................................6

2-2.Names of internal Components ..............................................................................................................7

3. Disassembly

3-1.Removing CABI R ASSY .........................................................................................................................8

3-2.Removing LCD ASSY,LCD FRAME ....................................................................................................... 9

3-3.Removing LENS ASSY ......................................................................................................................... 10

3-4.Removing MAIN PWB ASSY................................................................................................................ 11

3-5.Removing DCST PWB ASSY............................................................................................................... 11

3-6.Removing BATTERY HOLDER, LENS BARIA ASSY ........................................................................ 12

3-7.Removing SW PWB ASSY ................................................................................................................... 13

4. Adjustment and Inspection

4-1. Important point Adjustment when Replacing Major Parts ............................................................... 14

4-2.Preparations for Adjustment ................................................................................................................ 14

4-2-1.Required Measuring Equipment ................................................................................................... 14

4-2-2.List of Jig Used ............................................................................................................................... 14

4-2-3.Measuring Intrument and Jig Connection Diagram .................................................................... 15

4-2-4.Setup for adjustment...................................................................................................................... 15

4-2-5.Various downloading software decompressions, preservation methods, and notes ............. 16

4-2-6.Install the DSC jig driver and the PC adjustment software ....................................................... 17

4-3.Adjustment Using the PC ..................................................................................................................... 18

4-3-1.Setting up the Adjustment Software............................................................................................. 18

4-3-2.Starting the Adjustment Software ................................................................................................. 20

4-3-3.[ L ] : LCD Adjustment ................................................................................................................... 21

4-3-4.[ B ] : Battery adjustment ............................................................................................................... 22

4-3-5.[ C ] : CCD defect correction Adjustment .................................................................................... 23

4-3-6.[ P ] : Picture Adjustment .............................................................................................................. 24

4-3-7.[ A ] : AF Adjustment ...................................................................................................................... 25

4-3-8.[ F ] : Flash Adjustment ................................................................................................................. 26

4-3-9.[ E ] : End Setting ........................................................................................................................... 27

4-4.Inspection ............................................................................................................................................... 29

4-4-1.Inspection and shipment setting................................................................................................... 29

4-5.Hexadecimal to decimal Conversion Table ........................................................................................ 29

5. Appendix

5-1.List of Related Technical Updates Issued ......................................................................................... 30

Revised:3.Sep.2001

FinePix2600Zoom (U/E/EG) SERVICE GUIDE

1.Specifications

System

Model Digital camera FinePix2600 ZOOM

CCD Sensor 1/2.7-inch square pixel CCD

Total number of pixels: Approx. 2.11 million; Number of effective pixels: 2.0 million

Image file size 1600 × 1200 pixels (1.92 million pixels)/1280 × 960 pixels/640 × 480 pixels

File format Still image: JPEG (Exif Ver.2.1), DPOF-compatible

Movie: AVI format, motion JPEG

*Design rule for Camera File system compliant

Viewfinder Real image optical; Frame coverage: 80%

Lens Fujinon optical 3× zoom lens F3.5/F8.7

Storage media SmartMedia (3.3V)

Number of frames recorded

File Size 1600 × 1200 1280 × 960

640 × 480

Movie

Quality Mode FINE NORMAL BASIC FINE NORMAL NORMAL -

Image Data Size

Approx.770KB Approx.390KB Approx.200KB Approx.620KB Approx.320KB Approx.130KB

4MB (MG-4S) 4 9 19 6 12 30

Approx.23sec.

8MB (MG-8S) 10 19 39 12 25 61

Approx.47sec.

16MB (MG-16S/SW) 20 39 75 25 49 122

Approx.94sec.

32MB (MG-32S/SW) 41 79 152 50 99 247

Approx.191sec.

64MB (MG-64S/SW) 82 159 306 101 198 497

Approx.385sec.

128MB (MG-128S/SW) 166 319 613 204 398 997

Approx.774sec.

1. Specifications

1-1. Product Specifications

Focus distance f = 6-18 mm (equivalent to 38-114 mm on a 35 mm camera)

Exposure control 64 zones TTL metering, Program AE (exposure compensation available in Manual mode)

Sensitivity Equivalent to ISO 100

White balance Auto (7 positions selectable in Manual mode)

Focal range Normal:Approx. 0.8 m (2.6 ft.) in. to infinity

Macro: Approx.10 cm (3.9 in.) to 80 cm (2.6 ft.)

Shutter speeds Variable-speed, 1/2 to 1/1000 sec. (Using AE)

Flash (Auto flash using Effective range: Wide-angle Approx. 0.2 m-3.0 m (0.6 ft.-9.8 ft.)

flash control sensor) : Telephoto Approx. 0.8 m-3.0 m (2.6 ft.-9.8 ft.)

Flash modes: Auto, Red-Eye Reduction, Forced Flash, Suppressed Flash, Slow Synchro

LCD monitor 1.8-inches, 72,000-pixels D-TFD

Self-Timer 10 sec. timer clock

Input/Output Terminals

(USB) socket USB (1) for image data output with a personal computer

DC IN 3V (Power input) Special AC Power Adapter AC-3V

socket

FinePix2600Zoom (U/E/EG) SERVICE GUIDE

1.Specifications

Power supply and Others

Power supply Use one of the following:

z 2AA-size Ni-MH (nickel metal hydride) batteries (provided)

z AC Power Adapter AC-3V (sold separately)

Number of available shots using batteries (fully charged)

Battery Type With LCD monitor ON With LCD monitor OFF

Ni-MH battery

Approx. 150 frames* Approx. 300 frames*

HR-3UF

*With fully charged battery

This indicates the number of available frames shot consecutively at room tempera-

ture with a flash use rate of 50%.

Conditions for use Temperature: 0

C to +40

C (+32

F to +104

F); 80% humidity or less (no condensation)

Camera dimensions 99.8 mm × 65 mm × 53.9 mm/3.9 in. × 2.6 in. × 2.1 in.

(W/H/D) (not including accessories and attachments)

Camera mass (weight) Approx. 200 g/7.1 oz (not including accessories, batteries or SmartMedia)

Mass (weight) for Approx. 255 g/9.0 oz (including batteries and SmartMedia)

photography

Accessories z AA-size Nickel-Metal Hydride (Ni-MH) Batteries HR-3UF (2)

z SmartMedia (16MB, 3.3V) (1) Supplied with: Anti-static case (1)

Index label (1)

z Hand Strap (1)

z Battery Charger BC-NHS (1)

z Interface Set (1) CD-ROM (1)

Special USB cable with Noise Suppression core (1)

Software Quick Start Guide (1)

z Owner's Manual (1)

Optional Accessories z SmartMedia MG-4S: 4MB, 3.3V MG-8S: 8MB, 3.3V

MG-16S/SW: 16MB, 3.3V MG-32S/SW: 32MB, 3.3V

MG-64/SW: 64MB, 3.3V MG-128SW: 128MB, 3.3V

z AC Power Adapter AC-3V

z Fujifilm Rechargeable Battery 2HR-3UF

z Fujifilm Battery charger with Battery BK-NH

z SC-FX26

z FD-A2 Floppy Disk Adapter (FlashPath) Windows 95/98/98SE/Me/NT4.0

Mac OS 7.6.1 to 9.1

z SM-R2 Image Memory Card Reader

Compatible with Windows 98/98SE, Windows Me, Windows 2000 Professional,

iMac or Power Macintosh PCs which support USB as standard.

z DM-R1 Image Memory Card Reader

Compatible with Windows 98SE, Windows 2000 Professional (read-only),

iMacDV and Power Macintosh PCs with FireWire as a standard feature. Mac OS

8.5.1 to 9.1

z PC-AD3 PC Card Adapter

2.Names of Components

FinePix2600Zoom (U/E/EG) SERVICE GUIDE

2. Names of Components

2-1.Names of External Components

Viewfinder window

POWER swich

Flash control sensor

(USB)socket

DC IN 3V(Power input)

socket

Shutter button

Flash

Self-timer lamp

Lens cover

Lens

( ) ( ) button

Viewfinder lamp

Viewfinder

LCD monitor

Battery cover

Tripod mount

SmartMedia slot

Battery compartment

Strap mount

BACK button

MENU/OK button

button

DISP button

2. Names of Components

FinePix2600Zoom (U/E/EG) SERVICE GUIDE

2-2.Names of internal Components

CABI R ASSY

SW PWB ASSY

LCDFP PWB ASSY

LCD ASSY

LCD FRAME

FRAME L

MAIN PWB ASSY

DCST PWB ASSY

RSW PWB ASSY

BATTERY HOLDER

LENS ASSY

FRAME R

CABI F ASSY

CABI INNNER(N.S.)

BATTERY LID ASSY

3. Disassembly

FinePix2600Zoom (U/E/EG) SERVICE GUIDE

(1) Five screws are removed.

(2) Battery lid is opened.

(3) CABI R ASSY is removed in the direction of the arrow.

(4) CN305 is removed.

3. Disassembly

3-1.Removing CABI R ASSY

Remove in the order indicated by circled numbers.

<step1>

<step2>

<step3>

Revised:3.Sep.2001

3. Disassembly

FinePix2600Zoom (U/E/EG) SERVICE GUIDE

3-2.Removing LCD ASSY,LCD FRAME.

(1) CN801and CN501 are removed.

(2) Hook of LCD FRAME in two places is removed.

(3) LCD ASSY is removed on the direction of the

arrow.

(4) LCD FP PWB is removed in the direction of the arrow.

(5) Two screws are removed.

(6) Hook of LCD FRAME in two places is removed.

(7) Removes in the direction of the arrow.

<step1>

<step2>

<step3>

Remove in the order indicated by circled numbers.

Revised:3.Sep.2001

3. Disassembly

FinePix2600Zoom (U/E/EG) SERVICE GUIDE

(1) CN1 and CN201 are removed.

(2) LENS ASSY is removed in the direction of the arrow.

<step1>

* Method of installing FERRITE CORE when LENS ASSY is exchanged

(1) Match FERRITE CORE to REF.No C2 on the

CCD PWB ASSY.

(2) Pass FERRITE CORE through FPC of LENS ASSY.

(3) Make FERRITE CORE a center, and put insulating

tape of 9mm in width and 15mm in length.

FPC

15mm

9mm

2mm

Insulating tape

FERRITE CORE

3-3.Removing LENS ASSY.

Remove in the order indicated by circled numbers.

Revised:3.Sep.2001

3. Disassembly

FinePix2600Zoom (U/E/EG) SERVICE GUIDE

3-5.Removing DCST PWB ASSY

(1) Discharge the charge with the flash.

(2) Three screws are removed.

(3) DCST PWB ASSY is removed in the direction

of the arrow.

Thing to remove DCST PWB ASSY after flash is discharged.

<step1>

3-4.Removing MAIN PWB ASSY

(1) One screws are removed.

(2) CN301 and CN304 are removed.

(3) LENZ ASSY is removed in the direction of the arrow.

<step1>

Remove in the order indicated by circled numbers.

3. Disassembly

FinePix2600Zoom (U/E/EG) SERVICE GUIDE

3-6.Removing BATTERY HOLDER, LENS BARIA ASSY

Change MODE DIAL to the camera mode.

(1) Remove FRAME R and FRAME L.

(2) Two screws are removed.

(3) Remove BATTERY HOLDER in the direction

of the arrow.

(4) Four screws are removed.

(5) Have the part of (A) by the finger, and expand

CABI F in the direction of the arrow(5).

And, remove INNER CABI in the direction of (B).

(6) Expand CABI F in the direction of (6),

and remove the whole of INNER CABI.

* INNER CABI is installed in CABI F with the hook in

four places.

<step1>

<step2>

<step3>

INNER CABI

Remove in the order indicated by circled numbers.

3. Disassembly

FinePix2600Zoom (U/E/EG) SERVICE GUIDE

(7) Close LENS BARIA.

(8) Remove the screw, and remove BARIA GUIDE.

(9) Remove the screw, and remove the BARIA hook

in the direction of the arrow.

3-7.Removing SW PWB ASSY

(1) Three screws are removed.

(2) Remove SW PWB ASSY in the direction of the arrow.

<step4>

<step1>

BARIA hook

BARIA GUIDE

* How to install BARIA hook

1. Close LENS BARIA.

2. Set [BARIA hook] to the position of C, and stop the screw.

Remove in the order indicated by circled numbers.

4. Adjustment and Inspection

FinePix2600Zoom (U/E/EG) SERVICE GUIDE

4. Adjustment and Inspection

4-1. Important point Adjustment when Replacing Major Parts

Check and adjust of the items indicated by O in the table below when replacing the MAIN PWB ASSY,DCST PWB ASSY,

LENS ASSY,LCD ASSY.(Note that adjustment is not required when units other than those shown below are replaced.)

4-2. Preparations for Adjustment

4-2-1. Required Measuring Equipment

*1 Adjust in the following order when replacing the LENS ASSY and MAIN PWB ASSY.

Picture adjustment ---> CCD defect adjustment ---> AF adjustment ---> Flash adjustment

*2 Adjust the Flash following Picture adjustment.

MAIN PWB ASSY DCST PWBASSY LENS ASSY(*1) LCD ASSY

Battery adjustment

LCD adjustment

CCD defect adjustment

Picture adjustment

AF adjustment

Flash adjustment (*2)

End setting Required for all when replacing and adjusting the above parts. See P19 and P29 for details of termination setting.

Replacement parts

Adjustments

Measuring equipment Remarks

Monitor TV

Regulated power supply

Pattern box PTB450 or equivalent

Waveform monitor Used for function checks

Digital voltmeter

PC Used for various adjustments and operation checks (PC-AT compatible, Windows 98)

Brightness meter LS-110 (Minolta) or equivalent

Color temperature meter Color Meter IIIF (Minolta) or equivalent

4-2-2. List of Jig Used

(Note1) Please downloaded from Web server

(http://fujifilm-di.intranets.com/).

(Note2) The image contents included on the standard

card are as shown below.

Productname/type name Pats.No Use Remarks

FilterLB140 ZJ00006-100 Camera System adjustments Common with the DS-30/DS-20/DS-7

AF Chart J-6080-875-A AF adjustment Common with the 8mmVTR/MX500/MX600

Close_up lens(f=600mm) ZJ00007-100 AF adjustment Common with the 8mmVTR/MX500/MX600

Lens holder ZJ00008-100 AF adjustment Common with the 8mmVTR/MX500/MX600

Stand ZJ00009-100 AF adjustment Common with the 8mmVTR/MX500/MX600

Base plate ZJ00010-100 AF adjustment Common with the 8mmVTR/MX500/MX600

Gray Chart(Reflective type) ZJ00254-100 Flash adjustmen Common with the MX700/MX500

USB cable FZ03529-100 For PC adjustment Common with the FinePix4700zoom

Power cable jig ZJ00214-100 System adjustment Common with the DS-10/FinePix1500

FinePix2600Zoom ZJ00505-101 For PC adjustment Operates only on Win98 English OS

PC adjustment software (Note1)

AC adapter(AC-3V) ----------------- Adjustment overall Accessories

DSC jig driver setup ZJ00476-100 For PC setup DSC jig driver setup(Note1)

LCD adjustment card ZJ00433-100 For LCD adjustment FinePix2300/2500Z and commonness(Note1)(Note2)

Baseplat e (∑-13-3/Sigma

Optical Equipment)

Lens holder (∑-40-50/Sigma

Optical Equipment)

Stand (∑-32-130/Sigma

Optical Equipment)

File Name Image Contents

DSC00001.jpg Color bar

DSC00002.jpg Monoscope

DSC00003.jpg Full White

DSC00004.jpg Full Black

DSC00005.jpg Brightness adjustment chart

DSC00006.jpg Natural Picture

Revised:3.Sep.2001

Revised:12.Sep.2001

FinePix2600Zoom (U/E/EG) SERVICE GUIDE

4. Adjustment and Inspection

DC IN terminal

Voltmeter

(Note 1)

(sensing)

USB terminal

4-2-3.Measuring Intrument and Jig Connection Diagram

Note 1: Always check the input voltage in the vicinity of the DC IN terminal when adjusting.

FinePix2600Zoom

DC_5V

Power supply cable jig

Regulated power supply

4-2-4. Setup for adjustment

(1) Preparatory setup for Picture adjustment

(Fig.A)

Adjust the distance between the reference face of the camera

(see *1) and the filter (LB140) to 30±5mm, and adjust the dis-

tance between the filter (LB140) and the pattern box to a maxi-

mum of 50mm. Pattern box specifications are as follows.

1. Brightness:

160±5cd/m

(with LB140 filter)

No chart, center of pattern box

Minolta brightness meter LS-110 or equivalent

* Measurement

Place the filter (LB140) against the pattern box.

With the filter (LB140) in contact with the brightness meter, adjust

the pattern box brightness to 160±5cd/m

2. Color temperature:

6100 ± 50 K (with LB140 filter)

No chart, center of pattern box

Minolta color meter IIIF or equivalent

* Measurement

Place the filter (LB140) against the pattern box.

With the filter (LB140) in contact with the color tempera-

ture meter, adjust the pattern box color temperature to

6100 ± 50 K.

Filter(LB140)

Pattern

BOX

<Fig.A> Preparations for Picture Adjustment

Within 50mm

4. Adjustment and Inspection

FinePix2600Zoom (U/E/EG) SERVICE GUIDE

(2) Preparations for Flash adjustment (Fig.B)

As Flash adjustment is easily affected by external light, the

area around the gray chart should be as dark as possible.

The chart is mounted at a distance of 100 cm from the refer-

ence face of the camera.

An Oxford Gray (No.22) chart (manufactured by Superior)

with a reflectivity of 18±0.7% is used as the gray chart.

(3) Environment setup for AF adjustment (Fig.C)

1) Set the AF chart from the LENS front to 60cm.

2) Put the conversion lens(600mm) in front of LENZ.

3) Illuminate the AF chart with the light source.

Ensure that the brightness at the surface of the AF

chart is 9.0~12.0Ev.

4) Locate the conversion lens concentric with the

camera lens.

Gray chart

100cm

<Fig.B> Preparations for Flash Adjustment

<Fig.C> AF Adjustment Environment

AF chart

10+-1mm

Fluorescent lamp stand

60cm+-1cm

4-2-5.Various downloading software decompressions,

preservation methods, and notes

The PC adjustment software are in a specified Web server,

and both of these are the compression of ZIP form files.

Therefore, after downloading these compression files from

the Web server, the decompression of the file is necessary.

In the decompression software, if the decompression of the

ZIP form can be done, any software is OK.

(Please prepare each one for the decompression software.)

The decompression and the preservation method of the PC

adjustment software and the firmware are described

to the following.

(1) The PC adjustment soft decompression and

preservation method

<step1>

Download compressed PC adjustment software (ZJ00505-

100.ZIP) from Web server (http://fujifilm-di.intranets.com/).

<step2>

Defrost the downloaded compression software.

(Note)

*Specify the preservation drive for C drive if it is decompres-

sion software which can specify the preservation drive.

*Similarly, defrost without making a new folder if it is decom-

pression software which can be defrosted without making a

new folder.

*Defrost simply if the decompression software which you

have cannot specify the drive specification and the folder

making.

<step3>

The folder named ZJ00505-100 can be made by defrosting

without specifying anything. <Fig.D-1>

Then, copy the folder named FinePix2600ZU_E in this folder

in C drive.(Fig.D-2)

The folder of ZJ00505-100 becomes unnecessary at the

end, and delete this folder.

ZJ00505-100

FinePix2600Z_UE

My Computer

3.5inch FD(A:)

(C:)

<Fig.D-1>

FinePix2600Z_UE

My Computer

3.5inch FD(A:)

(C:)

<Fig.D-2>

ZJ00505-100

Revised:3.Sep.2001

FinePix2600Zoom (U/E/EG) SERVICE GUIDE

4. Adjustment and Inspection

4-2-6.Install the DSC jig driver and the PC adjust-

ment software

* Since this camera uses the USB for communications with the

personal computer, in order to start the PC adjustment soft-

ware, [the DSC jig driver] needs to be installed in the personal

computer beforehand.

* The DSC jig driver is the same as that for the FinePix 6800Z,

so if this jig driver software is already installed in the personal

computer, it is not necessary to install it.

The procedure is given below.

(1)Installation of DSC jig driver

DSC jig driver(ZJ00476-100.ZIP) is downloaded from Web

server (http://fujifilm-di.intranets.com/).

Defrost the downloaded compression software

Double-click setup.exe in the folder of defrosted ZJ00476-

100 and install Fuji FILM DSC Jig Driver as follows.

Install the software in [C:\ProgramFiles\Fjig]

according to the instructions on the PC's screen.

(2)Startup of PC adjustment software

When the folder has been copied to the C drive, double-click on the

file C:\FinePix2600Z_UE\ffw217.exe (Fig.D-3(1)) to start the adjust-

ment software.

<Fig.D-3> ffw217.exe screen display (Windows Explorer)

(Caution)[Important]

(a) PC adjustment software can not start when there is folder of

FinePix2600ZU_E in folder named ZJ00505-100.(Fig.D-1)

Please preserve the folder of FinePix2600Z_UE right under C drive.(Fig.D-2)

(b) Please do not change the foldername named FinePix2600Z_UE.

PC adjustment software can not start when foldername is changed.

(1)

4. Adjustment and Inspection

FinePix2600Zoom (U/E/EG) SERVICE GUIDE

4-3. Adjustment Using the PC

* As the initial setup is included in the FFW217.ini file, follow the

procedure described below. Note that the software will not

run if the file name is changed.

* As steps 3~6 in initial setup are included in the FFW217.ini file, all

that is required is to verify details.

* Do not alter the user program (FX2600Z_UE) under any cir-

cumstances. The software will not run if it has been altered

in any way.

4-3-1. Setting up the Adjustment Software

Double-click on the executable file FFW217.exe (Fig.D-(1)) to

display the FFW Start-up Screen (Fig.E).

Select the Setting menu (Fig.F-(1)) from the menu bar on the

Menu screen, and then select Mode setting (Fig.F-(2)).

Select the EVR menu (Fig.G-(1)) from the Customize dialog

screen, and setup as follows (Fig.G-(2)).

Item Setup details

etc (-V2) Use (

check)

LANC page Use (

check)

Select the Etc menu (Fig.H-(1)) from the Customize dialog

screen, and setup as follows (Fig.H-(2)).

Item Setup details

Number of automatic measurements

Enable mode change

No check (

un used)

Use Japanese fonts

No check (

un used)

<Fig.G> EVR Dialog Box Screen<Fig.H> Etc Dialog Box Screen

(2)

(1)(1)(2)

Apply

fx2600z_ue

<Fig.F> Mode Setting Select Screen

(1)

(2)

fx2600z_ue

<Fig.E> FFWJ217.EXE Start-up Screen

fx2600z_ue

FinePix2600Zoom (U/E/EG) SERVICE GUIDE

4. Adjustment and Inspection

Cautions When Adjusting

*1) FinePix2600Zoom cannot adjust the EVR data reading

and writing.(Details are right tables.)

*2) End Setting returns the camera from the Jig mode to

the Product Mode (see P27/28).

End Setting is required when using the PC adjustment

software, even when replacing boards or units other

than those noted above. Failure to run End Setting will

prevent identification as Mass Storage.

When the camera is connected to the PC, and prevent

communication with the PC.

*3) When all adjustment have been completed, always

check that the camera is identified as Mass Storage.

*4) Start from Picture adjustment absolutely when you

exchange LENS ASSY and MAIN PWB ASSY.

Select Hardware from the Customize Setup Screen (Fig.I-

(1)). Setup as follows on the Hardware menu (Fig.I-(2)).

Item Setup. details

Debug mode Select Ignore Focus

When setup on the three menus noted above (EVR, Etc, Hard

ware) is complete, click on Apply (Fig.I-(3)) on the Customize

dialog screen to finish.

After the setup has been applied, further setup is unnecessary.

Note:

Setting Disable OKNG Display to OFF on the screen shown in

Fig.H displays OK on the screen if adjustment is OK, and NG if

not (either setting may be entered).

Menu Command Details

Operation Start Program start

Stop Program stop

Temporary stop Temporary program stop

Step 0 Do not use

End Terminate program

Program Reload Program (*.ff) reload

Select Program (*.ff) select

Edit Program (*.ff) edit

Data ad[ ] Do not use

rd[ ] Do not use

SW Do not use

fsw Do not use

EVR Do not use *1)

Mode File record Do not use

NGSTOP Program stopped if

adjustment is NG

STEP Do not use

LINE Do not use

AUTO Do not use

Setting OKNG clear Do not use

Mode set Sets up mode

Automaticadjustment

Execution setting for Auto

Adjust in user program

Help Help Basic software help

FF help User program help

Focus Not used with this

adjustment software

Version Version information for

basic software

<Table> FFW217.exe Commands

<Fig.I> Hardware Dialog Box Screen

(1)

(2)

(3)

Apply

fx2600z_ue

Revised:3.Sep.2001

4. Adjustment and Inspection

FinePix2600Zoom (U/E/EG) SERVICE GUIDE

4-3-2.Starting the Adjustment Software

Double-click on the executable file FFW217.exe.

--->Start-up screen of FFW(figure E) displays it.

Select Operation -->Start to run (Fig.1-(1)-->Fig.1-(2)).

--->The[Start screen (Figure 2)] displays.

Press the Enter key of PC after setting the camera to the

Jig mode.

--->The[Adjustment item select screen (Figure 3)]

displays.

* Method of setting Jig mode

1) Input 3.0+-0.1V from DC_IN.

2) Set the mode dial to [CAM] mode.

3) Connect the USB cable.

4) Open the lens barrier.

5) Put in LCD adjustment card.

6) Open the battery cover.

7) Please holding down the [Release] button,

them trun on the camera.

8) Press Enter key when the setting end.

* Adjustment item list

<Fig.2> FinePix 2600Zoom PC Adjustment Soft-

ware Start Screen

<Fig.3> Adjustment Items Select Screen

<Fig.1> FFW217.EXE Start-up Screen

Adjustment item Selection

LCD adjustment Press the L key on the PC.

CCD defect correction Press the C key on the PC.

Battery adjustment Press the M key on the PC.

Picture adjustment Press the P key on the PC.

AF adjustment Press the A key on the PC.

Flash adjustment Press the F key on the PC.

End setting Press the E key on the PC.

(1) (2)

fx2600z_ue

Revised:12.Sep.2001

Page is loading ...

Fujifilm FINEPIX 2600 ZOOM User manual

Fujifilm FINEPIX 2600 ZOOM User manual

Fujifilm FINEPIX 2600 ZOOM User manual

Related papers

Other documents