Putco 270524B Installation guide

Brand
Putco
Model
270524B
Category
Wall & ceiling mounts accessories
Type
Installation guide

Putco 270524B is a grille for 2007+ Jeep Wranglers. It is made of either stainless steel or aluminum and comes with all the necessary hardware for installation. The grille is designed to be easy to install, with no drilling required. It also features a notch in the top of the grille that aligns with the "P" in the Jeep logo, ensuring a precise fit.

In addition to its aesthetic appeal, the Putco 270524B grille also offers some functional benefits. It is designed to protect the Jeep's radiator from damage, and it can also improve airflow to the engine.

Putco 270524B is a grille for 2007+ Jeep Wranglers. It is made of either stainless steel or aluminum and comes with all the necessary hardware for installation. The grille is designed to be easy to install, with no drilling required. It also features a notch in the top of the grille that aligns with the "P" in the Jeep logo, ensuring a precise fit.

In addition to its aesthetic appeal, the Putco 270524B grille also offers some functional benefits. It is designed to protect the Jeep's radiator from damage, and it can also improve airflow to the engine.

270524B, 270524BL
64178, 64178L
LIMITED 90 DAY WARRANTY
Putco guarantees it’s Stainless Steel and Aluminum products against defects in workmanship and material for as long as you
own your vehicle. All painted products have a 90 day warranty on the painted surface. Any defects resulting from faulty
material or workmanship will be warranted by Putco and repaired or replaced at our discretion. Putco assumes no extra labor
costs. Damages caused by freight carriers, improper installation, misuse, collision, or neglect will not be warranted by Putco.
11/14/2014 - JW 270524BI
2007+ Jeep Wrangler Grille Installation Instructions
Congratulations on your purchase of a high quality PUTCO product. Should you
need any application or technical assistance, feel free to call us at: 1-800-357-9261
Monday-Friday 8:00 a.m. - 5:00 p.m. (Central Standard Time)
Contact your PUTCO dealer for other quality accessories.
Please read all instructions before installation and to check to see that all parts are included.
Tools Needed:
- 7/16" Wrench
- 5/32" Hex Wrench
- 5/16" Drill Bit
- Drill
- Flat Head Screw Driver
- Saw- Recommended:
Oscillating Hand Tool
Grille Installation
1. Remove Grille from packaging. Check to see if all parts from above table of kit contents are
included.
2. Remove 6 plastic retaining clips with flat
head screw driver (locations shown
above) by removing center rivet pin first.
3. Once clips are removed, remove grille by
pulling straight out and unhooking the
marker lights.
KIT CONTENTS:
Description Qty.
Grille (Stainless Steel or Aluminum) 1
1/4" - 20 x 3/4" SS bolt 20
1/4" - 20 SS Lock Nut 20
1/4" SS Washer 20
Only for Lighted Grille (below)
20" Luminix Light 1
Wiring Harness 1
Switch 1
Light Bar Installation Instructions 1
270524B, 270524BL
64178, 64178L
LIMITED 90 DAY WARRANTY
Putco guarantees it’s Stainless Steel and Aluminum products against defects in workmanship and material for as long as you
own your vehicle. All painted products have a 90 day warranty on the painted surface. Any defects resulting from faulty
material or workmanship will be warranted by Putco and repaired or replaced at our discretion. Putco assumes no extra labor
costs. Damages caused by freight carriers, improper installation, misuse, collision, or neglect will not be warranted by Putco.
11/14/2014 - JW 270524BI
4. Use saw to cut inner section of grille out. Mark 3.25" from top and bottom, these will be your cut
lines. Only inner bars will be removed. (Recommend using tape around cut line) (white
shaded area below).
5. Place Putco grille over cut jeep grille. Align notch in top of grille with the "P" in the Jeep logo.
Measure grille side to side and up and down to verify it is set on the Jeep grille square.
Mark and drill all 20 holes around border of Putco grille. Use 5/16" drill bit.
6. Bolt Putco grille to Jeep grille using 1/4"-20 hardware; washer and nut goes on back side of
grille. Use 7/16" wrench and 5/32" hex wrench to tighten hardware.
7. Reinstall grille shell into Jeep. Enjoy!!
For Lighted grilles, refer to the Wiring Installation on Light Bar Installation Instructions for
wiring instructions
3.25” From Top and Bottom
Cut
  • Page 1 1
  • Page 2 2

Putco 270524B Installation guide

Brand
Putco
Model
270524B
Category
Wall & ceiling mounts accessories
Type
Installation guide

Putco 270524B is a grille for 2007+ Jeep Wranglers. It is made of either stainless steel or aluminum and comes with all the necessary hardware for installation. The grille is designed to be easy to install, with no drilling required. It also features a notch in the top of the grille that aligns with the "P" in the Jeep logo, ensuring a precise fit.

In addition to its aesthetic appeal, the Putco 270524B grille also offers some functional benefits. It is designed to protect the Jeep's radiator from damage, and it can also improve airflow to the engine.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents