Veise 801 User manual

Brand: Veise

Model: 801

Type: User manual

Veise 801 is a versatile door lock designed to provide enhanced security and convenience for your home or office. With its adjustable backset that fits either 2-3/8''(60mm) or 2-3/4''(70mm) backset, it can be easily customized to suit your specific door requirements. The reversible lever allows for flexible installation on both left-handed and right-handed doors. Installation is made simple with the included mounting screws, latch and strike screws, and a user-friendly hand tool for lever disassembly.

Thank you for purchasing our products. Please review this manual thoroughly before operating your device.

All pictures in this manual are for illustration purpose only. Actual product may vary due to product upgrade.

Latch(A)

Strike(C)

Rear Lever

(E)

Front Lever

(F)

Latch & Strike

screws (B)

Mounting Screw

(D)

TOOL REQUIRED: Do not use an electric

screwdriver during installation.

Parts list

Latch x1

ALatch & Strike screws x4

BStrike x1

Mounting

Screw x2

DHand Tool x1

HRear Lever x1

EFront Lever x1

1. Prepare the door

and check dimensions

If your door already has the holes shown in the picture

below, proceed to the next step, if your door does not

have holes, use the mounting template to drill a new hole.

2-1/8"

(54mm) 1"

(25mm)

2-3/8" or 2-3/4"

(60 or 70mm)

Door thickness:

1-3/8" to 2"

(35mm or 50mm)

25mm

2. Latch backset adjustment

Backset is the distance from the door edge to the center of the hole in the door.

The latch is provided with adjustable design which can fit either 2-3/8’’(60mm) or 2-3/4’’(70mm)

backset.

2-3/8"

(60mm)

2-3/4"

(70mm)

A. If the backset of your

door is 2-3/8"(60mm), no

need to adjust the latch.

B. If the backset of your door is 2-3/4"(70mm), please adjust the latch.

3. Install latch and strike

The latch should be aligned with the

chiseled properly.

IMPORTANT:

Make sure the hole in door frame is drilled a minimum of

1" (25mm) deep.

IMPORTANT:

4. Reverse lever direction (Optional)

1. Find the joint point, press the point by using

the Hand Tool.

2. Till the joint point is pressed down completely,

then pull out the lever. Sometimes, it may

happen that the joint point is unable to be

pressed down completely, in this case, please

press the joint point along with pulling out the

lever.

Pull out

The front lever is installed for right-handed door in

default. If your door is left-handed, please

exchange the front and rear lever with each other.

While you exchange the lever direction, the edge of

inner mechanism may be a little sharp, please protect

your hands from being hurt.

IMPORTANT: WARM REMINDER:

ARear Lever disassembly steps

Joint point

Pull out

CExchange the lever

Exchange the lever of front and rear with each other,

press the lever back till you hear a mild “Ding” sound.

1. Rotate the lever and find the joint point of the lever

through the hole on the housing.

2. Press the joint point with the Hand Tool, till the joint

point is pressed down completely, then pull out the

lever.

Sometimes, it may happen that the joint point is

unable to be pressed down completely, in this case,

please press the joint point along with pulling out

the lever.

BFront Lever disassembly steps

Align the hole with the

inside joint point

5. Install front and rear lever

The base of spindle must be

rotated aligning to the hole.

6. Test the Lever

Keep the door open,

checking out front and rear

lever to test if it works

smoothly.

Veise 801 User manual

Veise 801 User manual

Related papers

Other documents