ELONGATED AND ROUND BIDET TOILET SEAT
XXXXXX
BP0657&BP0658
toilet seat
□ Use this product only for its intended use as directed in this manual.
□ Do not disassemble, repair, or remodel the unit, as this will void the warranty.
□ Do not stand or drop heavy objects on this product and do not insert any object
into openings or hose.
□ Do not pull or stress the water supply hose.
□ Do not use in hot water line. Temperature above 40℃ (104℉) will damage the
product and void your warranty.
□ Turn off the water supply before installing this bidet toilet seat.
□ Before begining the installation of this product, ensure all parts are present.
Compare all the parts with the Package Contents section of this manual. If any part is
missing or damaged, do not attempt to assemble, install, or operate the product.
Contact customer service for replacement parts at 1-855-HD-GLAClER or visit
www.HomeDepot.com.
Estimated Installation Time: 8 minutes.
□ Prohibits any indivisual from performaing any action with this symbol.
□ Prohibits any individual from dismantling product.
□ Keep away from any extreme heat or fire.
□ Operate only as instructed.
□ Always test your cleaning solution on an inconspicuous area before applying to
the entire surface. Avoid using aerosol products.
□ Wipe surfaces clean and rinse completely with water immediately after applying
cleaner. Rinse and dry any overspray that lands on nearby surfaces.
□ Do not allow cleaners to soak on surfaces.
□ Use a soft, dampened sponge or cloth. Never use an abrasive material such as a
brush or scouring pad to clean surfaces.
□ Do not allow chemicals and cosmetics (such as fingernail polish and aftershave)
to come in contact with the seat.
□ The ideal cleaning mixture is dishwashing soap and water. Rinse and dry with a
soft cloth.
□ Only connect the seat to a cold water supply of drinking quality at a pressure of
20 (139 kPa) - 80 psi (551 kPa).
Installation (continued)
Installation (continued)
Add the rubber washer inside.
Part Description Quantity
A Bidet Seat 1
B Installation Template 1
C Fixed Base 1
D Sliding Plates 2
E Connecting Bolts 2
F Nylon Nuts (for top mounting) 2
G Nuts (for bottom mounting) 2
H Washer (for bottom mounting) 2
I Water Inlet Hose 1
J T-Shaped Connector 1
K Installation Guide 1
2b 3
4 51 2a
89
10 11
6 7
Positioning the template
□ Wipe the bowl surface clean. Lay
the template (B) over the top of the
toilet bowl.
□ Position the template (B) to how
you want the bidet seat to pair up
with the bowl once installed.
Installing the top mount
fittings
□ Assemble nylon nut (F), fixed base
(C), sliding plates (D) and bolts (E) into
the ceramic in the order as shown .
□ Adjust the fixed base (C) and lock
the bolts (E). Make sure the fixed base
(C) is fixed on top.
Installing the bottom
mount fittings
□ Screw in the nuts (G) and
washer (H) from the underside of
the ceramic until the fixed base
(C) is fixed.
Removing the template
Positioning the seat
□ Align the bidet seat (A) with the
fixed base (C).
Attaching the seat
□ Push the bidet seat (A) backward
to attach it to the fixed base (C).
Latching the seat
□ You will hear a "click" when the
bidet seat (A) is securely locked in.
Removing the seat
□ Press the button and push the
seat forward forcefully to remove.
Turning off the water
shutoff value
□ Drain the remaining water from the
toilet cistern.
Disconnecting the inlet hose
□ Unscrew the existing toilet cistern inlet
hose from the wall.
Connecting the hoses
□ Assemble the toilet cistern
inlet hose, water inlet hose (I),
T-shaped connector (J) as
shown in the diagram.
Finishing installation
□ Make sure all joints are locked and
the knob on the bidet seat is in the
closed position to avoid water spray,
then turn on the water shutoff value to
use normally.
A B C
D E F
G H J
I K
J
I
B
E
D
C
F
H
G
toilet cistern
inlet hose
toilet cistern
inlet hose
water shutoff
value
water shutoff value
toilet cistern
inlet hose
B
B
Note: all joints should be locked to
avoid water leaking.
□ Remove the template (B) from the
bowl and discard it.
CAUTION:
