2. Home
  3. Lighting
  4. Stroboscopes & disco lights
  5. Arena Luci
  6. BARIO LED

Arena Luci BARIO LED User manual

  • Hello! I am an AI chatbot trained to assist you with the Arena Luci BARIO LED User manual. I’ve already reviewed the document and can help you find the information you need or explain it in simple terms. Just ask your questions, and providing more details will help me assist you more effectively!
This instruction manual contains important information
about the installation and use of the projector. Please
readandfollowtheseinstructionscarefully.
Thesecurity of thisdevice is guaranteed onlywiththe
proper use of the following instructions, therefore they
mustbekeptcarefully.
Neverinstallthedeviceinlocationseasilyaccessibleby
peoplewho ignoretheexistenceof this user'smanual
andsafetyinstructions.
Disconnect the unit from any power supply before
attemptinganyoperationincontactorinsidetheunit,and
whennotinuse.
Itisessentialthateachdeviceiscorrectlyearthedand
that electrical installation conforms to all relevant
standards.Neversupplytheunitwithouttheearthlink.
Priortoconnecttheunittothemainssupply,checkthe
outputvoltagefitstechnicalrequirementsonthelabel.
Neverletpowercordcomeintocontactwithothercables.
Nevertouchelectricalcontacts,eitherdirectlywithyour
fingers,orindirectlybymeansofsharpormetalobjects.
Makesurethatcablescannotcausetriphazard.
Donotattempttodismantleandmodifytheunit.
Due to high technological level of this unit, service
maintenanceshouldbeperformedbyspecialisedopera
tors.PleasecontactyourArenaLucidealerforanyissue.
Always ensure that the structure to which you are
attaching the unit issecure and is able tosupport the
weightofeachunit.
Always make sure you are using a safety chain
connectedtotheunit.
Do not allow contact with water or anyotherfluids, or
metallicobjects(IP20).
Donotinstalltheprojectorinareasofhighhumidity.The
unitisintendedonlyforindoorpurposes.
Avoidinstallingtheunitclosetoheatsources.
Neverleanthepowercordonhotunitsurfaces.
Allowedtobemounteddirectlyoninflammablesurfaces.
Keepaminimumdistanceof3mbetweenthedeviceand
theilluminatedsurfaces.
Avoiddirectexposuretothelightfromthelamp.Thelight
luminanceisharmfultotheeye.
Installtheunitwhereitcanbeeasilyaerated.
Avoidobstructionofin/outvents.
The lighting apparatus must be used only with its
protectiveshield.
The protective grill, lenses or ultraviolet filter must be
changediftheyarevisiblydamagedtothepointatwhich
their effectiveness is diminished, for example by
becomingcrackedordeeplyscratched.
Toensurethereliabilityoftheprojectoritshouldbekept
clean. The lens and filters should also be regularly
cleaned(atleastonceeverysixmonths)tomaintainan
optimumlightoutput.
Donotuseanysolventbasedcleaningagents.Useonly
asoft,dryantistaticcloth.
The installation of LED modules (including power
supplies)shouldbedoneaccordingtocurrenttechnical
rules and regulations. The installation should be
performedonlybyaqualifiedoperator.
Avoid contact with either corrosive agents or humidity
and moisture on delicate elements: damages from
corrosionarenotrefundedascomponentdefects.
WARNINGS
BARIOLED
User'sManual
ProfileLEDspotwithmanualzoomandDMX
control
Please note that as part of Arena Luci's ongoing commitment to continuous product development,
specifications are subject to change in the course of product improvement without notice.Arena Luci is not
responsiblefordamagesresultingfromimproperordifferentusethanexpected.
PRF0501935DWW
PRF0501935DNW
PRF0501935DW
2/8
BARIOLEDDMX
BEFORESTARTING
Removetheproductfromtheshippingcarton,checking
thatallthecomponentssuppliedarepresentinthebox.
Refer to the following packing list to check which
components must be present in the packaging. If any
componentismissingordamaged,contactyourArena
Lucidealerimmediately.
n°1profilespotBARIOLEDDMX
n°1filterframe
n°1coupleofCanonXLR5poleconnectors
(male/female)
Beforestartingtheinstallationofyourproductmakesu
rethattherearenoevidentdamagescausedbytrans
portation.Intheeventthattheprojectorisdamaged,do
not plug it in and do not attempt to use it until you
contactedyourArenaLucidealerforassistance.
INSTALLINGTHEPROJECTOR
Attach the projector by means of the central hole dia
meter 11mm on the fork; for suspended applications,
youmustalsofixtheprojectorwithasafetychainsecu
ringittothesupportstructureandtheringontherear
plate,besidesthehandle.
Loosenthesideknobto adjustthetiltofthe projector
(+50° / 50°); once positioned, tighten the knob firmly.
For a mounting on tripod, the projector should be
installedupsidedown.
Theprojectormustbefixedonasuitablesupportwhich
remainsstableduringoperation.Alwaysmakesurethe
standorstructuretowhichyouaresettingtheprojector
issecureandisabletobeartheweightofeachunit.
POWERSUPPLYMAINS
Disconnectthemainsvoltagefromthesystem.
Connect the power cord to the mains supply, paying
attentiontothevoltageandfrequencyindicatedonthe
label.
Respect the LNE polarity indicated on the terminals
(colorbrown=L,blue=N,yellow/green=E).
It is essential that each projector is correctly earthed
and that electrical installation conforms to all the
standardsofgoodpracticeandsafetyregulations.
Theprojectordoes not have builtin on/off switchand
turnsonimmediatelywhenpowerissupplied.
Itisrecommendedthattheprojectorisconnectedtothe
mainsviaaproperswitch,sothatitcanbeturnedon
andoffindividually.
Caution
Itisimportantthatthegroundconnectionofeachpro
jectorisrunaccordingtotherulesinforce.Thepower
absorptionoftheprojectoris55W.
FILTERFRAME
Thefilterframefitsinthefrontoftheprojector.Undothe
smallretainingknobontherightsideofthedeviceand
slide it backward to release the filter frame. Now it is
possibletoextractandinsertthefilterholder.
Opentheframeandinsertthecoloredgelandthenput
itbackinplaceontheprojector.Payattentiontokeep
thenotchontheframetotherightsideoftheprojector,
tomatchthefilterholder.Slideforwardtheknobandfa
stenittolockthefilterframe.
3/8
USER'SMANUAL
MANUALZOOMADJUSTMENT
Use the two knobs underneath the projector to ma
nuallyadjusttheapertureofthelightbeamtosuitany
typeofinstallation.
The beam spread can be adjusted from 19°
(handlesapart)to35°(handlestogether).
CONNECTINGCONTROLSIGNALS
Theprojector,inordertoberemotelycontrolled,requi
res a digital signal DMX 512 (1990). The connection
betweencontrollerandprojectorandbetweenprojector
andprojectormustbemadewithtwocoreshieldedca
ble with a section of at least 0.5mm
2
and connectors
modelCanonXLR5pinplugandsocket(supplied).In
carryingoutthewiringoftheconnectorsitisimportant
that the signal wires do not make contact with each
otheranddonottouchthecasingoftheplug.Theca
sing of the plug must not be in contact with other ob
jects possible sources of disturbance. The three
terminals have the numberingreferredto the polesof
theXLRconnectorsnormallyusedfortheconnectionof
the DMX: pin 1 = GND or braided screen, pin 2 =
DATA or coldpole,pin3 = DATA+orhotpole.Pin 4
andpin5arenotconnected.
Connect the signal coming from the controller to the
DMXsocketoftheprojectorlabeledDMXIN.Continue
connectingtheDMXOUTsockettotheDMXINsocket
ofthenextprojector.
TerminationoftheDMXsignal
Forinstallationswherethecablesignalmusttravellong
distances or where there are electrical noises, for
example a discotheque, it is recommended to use a
DMXterminator.TheDMXterminatorissimplyanXLR
connector with a resistance of 120Ω (Ohm) between
pins 2 and 3. The connector is then plugged into the
DMXOUTsocketonthelastprojectorinthechain.
4/8
BARIOLEDDMX
PROJECTORADDRESSES
The projector, to be remotely controlled, requires 2
DMXchannels.Eachprojectormustbegivena digital
start address number so that the correct projector re
sponds to the correct control signals.This digital start
address is the channel number from which the pro
jectorstarts to “listen” to the digital control information
beingsentoutfromthecontroller.Thisdigitalencoding
mustbedoneoneachprojector.
Thestartaddressofthecodingisassignedbysetting
thedesiredvalueusingthedisplayinterfaceontherear
panel. Press the MENU button on the keypad, the
display shows the word
DMX ADDR
and the DMX
address that is currently set for the projector; use the
UP or DOWN buttons to select the desired starting
address(ie.projector1address1,projector2address
3, projector 3 address 5, etc.); for fast forward press
andholdthebutton.
Youcanquicklyjumptotheminimumvalue(001)orthe
maximum value (511). To set the minimum, press UP
whilepressingDOWN;tosetthemaximum,pressDO
WNwhilepressingUP.
PressENTERtostore(thedisplayshows
-STORED-
),
orpressMENUtoreturn.
The number of selectable base addresses from the
electronicboardrangesfrom1to511.
OPERATION
Aftersupplyingthedevice,thesoftwareperformsare
set; at the end of the electronics reset routine, the
displayshowstheidlestate.
Intheidlestateyoucangetmanyinformations:
D001 . 100
38'C
D001isthebaseaddressoftheprojector.
.(blinkingdot)indicatesthepresenceofavalidDMXsi
gnal.
100isthemasterdimmerlevel(expressedin%).
38'Cistheinternaltemperatureofprojector,in°C.
In the absence of DMX signal (XLR connector
unplugged),theblinkingdotisoff.After60secondsof
inactivity,thedisplaybacklitshutsoff.Pressanykeyto
switchitonagain.
Setthe base address ofthe projector as seen before
Fig.01WiringdiagramforDMXsignalremotecontrol
5/8
USER'SMANUAL
andconnect the signalfrom DMX controllerto control
thevariousfunctionsoftheprojector.
WhentheprojectorisreceivingaDMXframe,ifthesi
gnalislost(orthecableisdisconnected)theprojector
holdsthecurrentlevelsofDMXchannelsandtheLED
sourceisstilldrivenwiththelevelssentinthelastvalid
DMXframe.
Then,iftheprojectoristurnedoffandon,anditisnot
connected to a valid DMX signal, the light intensity is
brought to 0% (unless you changed the option menu
"manual"priortoswitchoff,seelaterinoptionsettings).
ShouldthetemperatureoftheLEDboardincreaseover
85°C, the electronic management automatically redu
cesthelightintensityinordertobringthetemperature
backtoacceptablevalues.
Inaddition,thebrightnessofthelightisbroughttozero
when the temperature on the LED board rises above
100°C.
OPTIONMENU
To activate the display press any button. Then to
access the options of the projector press the MENU
button. The display shows the name of the option
starting from option 1, the base DMX address. Press
again the MENU button to scroll through the list of
options. Adjust the value with UP or DOWN buttons,
thenconfirmyourchoicewithENTER(thedisplaysho
ws
-STORED-
).
Ifyoudon'tpressENTER,allyourchangeswillbelost:
after 20seconds of inactivity inside the options menu,
thedisplayreturnsbacktotheidlestate.
Option1DMXaddress
When the display shows
DMX ADDR
with the current
DMXaddress,presstheUPorDOWNbuttonsasma
nytimesasrequiredtodisplaythenumberofthedesi
redchannel.Tofastforwardpressandholdthebutton.
Remember that you can quickly jump to theminimum
value(001)orthemaximumpossiblevalue.Tosetthe
minimum, press UP while pressing DOWN; to set the
maximum,pressDOWNwhilepressingUP.
PressENTERtostoreorMENUtogoback.
Option2Manuallevelsettings
Manual settings are only effective when there is no
DMX signal connected, instead they have no effect
when the DMX signal is present (message
-ERROR-
shown).
Whenthedisplayshows
MANUAL
,inthesecondrowit
shows the channel number (starting from 1) and the
current manually set level in DMX units, for example
CH1: 255
.
Thechannelnumberisblinking,whilethechannellevel
issteady.UsetheUPorDOWNbuttontoswitchtothe
desiredchannel(1 to 2), then pressENTER: now the
channel number is steady and the channel level is
blinking, indicating that you can modify its value. Use
UP or DOWN to adjust the channel level; for fast
forwardpressandholdthebutton.ThenpressMENU
toreturntothechannelselection.
Remember thatyoucanquicklyjump to the minimum
value(001)orthemaximumvalue(255).Tosetthemi
nimum,pressUPwhilepressingDOWN;tosetthema
ximum,pressDOWNwhilepressingUP.
Repeat the above steps until you finish your manual
settings. Finally press ENTER to save your job, the
displayshows
-STORED-
.
Thevaluesarestoredintothepermanentmemory,and
willbereproduceduntilyouconnecttheDMXsignal.
Note:
Afteryousetthemanualvalues,whentheprojectoris
turned off and on, and it is not connected to a valid
DMXsignal,thechannelslevelsforch.1,ch.2areauto
maticallyrecalledfrommemoryandtheLEDsourcewill
behaveaccordingly.
If you connect a DMX signal and then remove it, the
stored values become "disabled" and at the next igni
tion (without DMX) the manualvalues will beignored;
thelightintensityisbroughtto0%,whilech.2issetto0.
Inallcases,ifyouswitchontheprojectorwithavalid
DMX signal connected, the manual settings are igno
red.
Remember that if you don't press ENTER to save in
memory,themanualsettingswillbelostandwon'tbe
recalledatthenextpoweron.
Option3FanMode
This functionrelatesto thecontrolof the LEDcooling
fan.
When thedisplay shows
FAN MODE
, the secondrow
showsthecurrentoperatingmodeandyoucanchange
itbypressingUPorDOWNbutton:

MAX
Thefanisalwaysonatmaximumspeed.

OFF-MAX
Thefanisswitchedoffuntilthetemperatureisbelowa
minimumsetpoint(50°C),thenitstartsblowingatmini
mum speed and gradually increases in speed as the
temperature rises, reaching the maximum speed at
70°C.

MIN-MAX
The fan is always on at minimum speed when the
temperatureis belowa minimum setpoint(50°C), and
graduallyincreasesinspeedasthetemperaturerises,
reachingthemaximumspeedat70°C.
Press ENTER to confirm (the display shows
-STORED-
forawhile)orpressMENUtoquit.
Option4SoftwareVersion
Whenthedisplayshows
SW REV.
youcanreadinthe
second row the current software release installed on
6/8
BARIOLEDDMX
theprojector.
PressMENUorwait20secondstogoback.
DMXCHANNELFUNCTIONS
Inthefollowingdiagramsyouwillfindthecontrolvalues
inDMXunits(0255)forall2channelsoftheprojector.
Channel1Dimmer
Theintensityoflightisvariableinalinearwayfromoff
tothemaximum;inparticular,forDMXvalueequalto0
the LED source is off, for increasing intermediate va
luesthebrightnessgraduallyincreases,forvalueequal
to255theLEDsourceisonatitsmaximumintensity.
Channel2Strobe
The projector is able to generate an electronic strobe
effect, obtained by rapidly switching on and off the
LED.ThestrobeisdisabledforDMXvaluesbetween0
and 9, while for values between 10 and 255 the fre
quencyoftheflashesgraduallyincreases.
RDMFUNCTIONS
The Remote Device Management Protocol (RDM)
permits intelligent bidirectional communication
between devices from multiple manufacturers. RDM
permitsaconsoleorothercontrollingdevicetodiscover
andthen configure,monitorandmanage intermediate
and enddevices connected through a DMX512
network.
RespondersandControllersidentifythemselveswitha
48bitUniqueID(UID).TheUniqueID(UID)consistsof
a16bitManufacturerIDwitha32bitDeviceID.
The32bitdeviceIDisuniquethroughoutallproducts
manufactured under a specific Manufacturer ID, to
ensure that no two devices with the same UID will
appearontheDMX512network.
TherecommendedmethodforrepresentingtheUIDin
text is in hexadecimal format with a colon separating
theManufacturerIDandtheDeviceID.
Anexampleofsuchwouldbe:
mmmm:dddddddd
where mmmm is the Manufacturer ID in hexadecimal
andddddddddistheDeviceIDinhexadecimal.
ManufacturerIDforArenaLuciis:
0x00B0
DeviceIDforArenaLuci productsconsistsofa12bit
ProductIDfollowedbya20bitSerialNumber.
ProductIDforDalìLEDis:
0x047forPRF0501935DWW
0x048forPRF0501935DNW
0x049forPRF0501935DW
The UID that would appear on RDM Controllers is
then(e.g.0x00001istheSerialNumberinhexaecimal):
00B0:04700001forPRF0501935DWW
00B0:04800001forPRF0501935DNW
00B0:04900001forPRF0501935DW
RDMParameterMessages
RDM Parameter Messages are sent to set configu
rationandgetstatusinformationfromthedevice.
Get/SetIdentifyDeviceIDENTIFY_DEVICE
Thisparameterisusedfortheusertophysicallyidentify
thedevicerepresentedbytheUID.
Whena"StartIdentify"issentfromtheRDMcontroller
to the projector, the projectorwill respond by strobing
the light. To stop the strobing after detecting the unit,
send"StopIdentify".
GetDeviceInfoDEVICE_INFO
This parameter is used to retrieve a variety of
information about the device that is normally required
byacontroller.
RDMProtocolVersion:
Thisfieldcontainstheversionnumberofthepublished
RDMStandardsupportedbythedevice.
BarioLEDreturns1.00.
DeviceModelID:
7/8
USER'SMANUAL
This field identifies the Device Model ID of the Root
DeviceortheSubDevice.
BarioLEDreturns
00.47forPRF0501935DWW
00.48forPRF0501935DNW
00.49forPRF0501935DW
ProductCategory:
ThisfieldreportsaProductCategorybasedonthepro
duct’sprimaryfunction.
BarioLEDreturnsFixtureFixed.
SoftwareVersionID:
This fieldindicatestheSoftwareVersion ID forthede
vice.
BarioLEDreturns
04.70.01.00forPRF0501935DWW
04.80.01.00forPRF0501935DNW
04.90.01.00forPRF0501935DW.
DMX512Footprint:
This field specifies the DMX512 footprint (number of
consecutive DMX512 slots required). This information
can be used in conjunction with DMX_
START_ADDRESSforautopatchingcapabilities.
BarioLEDreturns02.
DMX512Personality:
This field specifies the current DMX512 Personality
setting for the projector and also the total number of
personalitiesavailable.
BarioLEDreturns01/01.
DMX512StartAddress:
ThisfieldshowsthecurrentDMX512StartingAddress.
SubDeviceCount:
This parameteris used to retrieve the number ofSub
DevicesrepresentedbytheRootDevice;adevicemay
containoneormoresubdevices,allhavingacommon
setofparameters.Anexampleofadevicewithsubde
vicesisadimmerrackcontaininganumberofdimmer
modulesubdevices.
BarioLEDhasn'tanysubdevice.
SensorCount:
Thisfieldindicatesthenumberofavailablesensorsina
RootDeviceorSubDevice.
SensorswillbeaddressedusingotherRDMsensorre
latedparametermessages.
BarioLEDhasn'tanyaddressablesensor.
Get/SetDMX512StartingAddress
DMX_START_ADDRESS
ThisparameterisusedtogetorsettheDMX512start
address. Useyour RDM controller's commands to set
thedesiredDMXaddress.
GetSoftwareVersionLabel
SOFTWARE_VERSION_LABEL
This parameterisusedto get a descriptiveASCIItext
label for the device’s operating software version. The
descriptivetextreturnedbythisparameterisintended
fordisplaytotheuser.Thelabelmaybeupto32cha
racters.
BarioLEDreturns1.00.
TheSoftwareVersionIDfieldfromtheDEVICE_INFO
parametershouldbeusedforcomparingdevicesfrom
thesameManufacturerwiththesameDeviceModelID
to determine if they are running identical software
versions.
Get/SetDMX512Personality
DMX_PERSONALITY
Thisparameterisusedtosettheprojector’sDMX512
Personality.Manydevicessuchasmovinglightshave
different DMX512 Personalities. Many RDM parame
tersmaybeaffectedbychangingpersonality.
BarioLEDhasonepersonality:
Mode1:2ch./02.
Parameter PERSONALITY_DESCRIPTION contains
the Personality Requested, the DMX512 Footprint for
that Personality, alongwith up to32 charactersof de
scription.
BarioLEDreturns:
Personality#01
SlotRequired:02
Descrip:Mode1:2ch.
GetDeviceModelDescription
DEVICE_MODEL_DESCRIPTION
Thisparameterprovidesatextdescriptionofupto32
characters for the device model type. Bario LED re
turns:
ProfileDMXandManualzoom.
GetManufacturerLabel
MANUFACTURER_LABEL
This parameter provides anASCII text response with
theManufacturernameforthedeviceofupto32cha
racters.
BarioLEDreturns:
ARENALUCIITALY.
Get/SetDeviceLabelDEVICE_LABEL
This parameter provides a mean of setting a
descriptive label of up to 32 characters for each
device.Thismaybeusedforidentifyingadimmer
racknumberorspecifyingthedevice'slocation.By
defaultthisfieldisempty.
8/8
BARIOLEDDMX
WARRANTYCONDITIONS
The unit is guaranteed for 24 months from the date of
purchase against defects in workmanship or materials
thatcomposeit.
This warranty does faults due to incorrect or improper
useofthedevice.
The warranty is immediately void if the unit has been
tamperedwithoropenedbyunauthorizedpersonnel.
The warranty provides, at the discretion ofArena Luci,
repairorreplacementoffaultyequipment.
Theserialnumberandmodelofthedevicearerequired
to obtain information or assistance from the dealer. We
invite youtotranscribethemintime: for anyrequest of
information or services, this will result in a quick and
effectiveoperation.
CERULES
The device meets the essential requirements of the
Directives LVD 2014/35/UE, EMC 2014/30/UE, RAEE
2012/19/UE, RoHS 2011/65/UE, Ecodesign
2009/125/CE  reg. (UE) 1194/2012, Energy label
2010/30/UE reg.(UE) 874/2012  reg. (UE) 518/2014,
GPSD2001/95/CE.
Warnings
Disposal of Old Electrical & Electronic Equipment
(applicable in the European Union and other European
countrieswithseparatecollectionsystems).
Theproduct shallnot betreated ashousehold
wastebutmustbehandedovertotheapplicable
collectionpointfortherecyclingofelectricaland
electronicequipment.Byensuringthisproductis
correctly disposed, you will help prevent potential
negativeconsequencesfortheenvironmentandhuman
health,whichcouldotherwisebecausedbyinappropriate
waste handling. The recycling of materials will help to
conserve natural resources. For more detailed
informationaboutrecyclingofthisproduct,pleasecontact
yourcityoffice,yourhouseholdwastedisposalserviceor
yoursupplier.
ArenaLucisrlviaSvizzera12/1446042CastelGoffredo(MN),Italy
Tel.+390376782411Fax+390376780973
www.arenaluci.com[email protected]
Powersupply
Powerconsumption
Source
ColourTemperature
Cooling
Beamaperture
Control
Connection
Material
Colour
Insulationclass
Weight
Dimensions
Protection
AmbientTemperature
Suitabletobefittedonnormallyinflammablesurfaces
Appliedstandards
230VAC50Hz
55Wmax
LEDmodule,interchangeable
3000K(WW)4000K(NW)5700K(W).CRI>90
Heatsinkwithlownoiseaxialfan,max8dB.
Manualzoom19°÷35°
DMX512,2controlchannelswithRDM
Threepolespowercord
Aluminiumandsteelplate
Epoxypowderpaintfinish,black
I
4.8kg(includedfilterframe)
420x114x135mm(body)
IP20
From15°Cto+40°C
TECHNICALSPECIFICATION
PRF0501935DENR2|06/2019
/