16 ASSEMBLY INSTRUCTIONS
CHECKING LIST FOR INSPECTION AFTER ASSEMBLY
CONTENTS
ASSEMBLY INSTRUCTIONS ..................................................................................... 1
TO THE DEALER..................................................................................................... 1
SAFETY ................................................................................................................... 1
UNPACKING AND CHECKING PARTS .................................................................. 2
Unpacking Iron Crate........................................................................................................ 2
The Accessories Packaged Together with Tractor...........................................................2
Contents of Accessory Case ............................................................................................3
Contents of Nylon Bag Attached with the Accessory Case ..............................................5
ASSEMBLY.............................................................................................................. 5
Removing the Battery ....................................................................................................... 5
Mounting the Right and Left Fenders ...............................................................................6
Installing the Lever Grip....................................................................................................6
Attaching the 3-Point Hitch Assembly...............................................................................6
Attaching the Fender Cover..............................................................................................7
Attaching the Tail Cover and Rear Fender Stay...............................................................7
Attaching the Tail Light and License Holder Stay.............................................................8
Attaching the Tail Light, Rear Fender Stay and the Turn Signal/Hazard Light.................9
Attaching the Front Combination Light ...........................................................................10
Attaching the License Light and Trailer Electrical Outlet ................................................11
Attaching the Steering Wheel ......................................................................................... 11
Attaching the Seat ..........................................................................................................12
Attaching the Check Plate ..............................................................................................12
Attaching the PTO Cover................................................................................................12
Hoisting the Tractor ........................................................................................................13
Attaching the Front Tires ................................................................................................13
Attaching the Rear Tires.................................................................................................14
Hooking up the Battery ................................................................................................... 15
Attaching the Tool Box....................................................................................................15
ADJUSTING THE HEAD LIGHT ALIGNMENT ...................................................... 15
CHECKING LIST FOR INSPECTION AFTER ASSEMBLY................................... 16
1ASSEMBLY INSTRUCTIONS
ASSEMBLY INSTRUCTIONS
TO THE DEALER
1. This manual contains procedures intended to assist
the dealer in unpacking and assembling the product
before delivering to the customer.
The customer's purchase is based on confidence in
both the product and your store. Observe the
procedures in this manual to assemble and adjust
equipment for your customer's safety and satisfaction.
When fully assembled, check function of each part and
feature.
2. The following safety alert symbol marks and
indications are found throughout this manual in steps
where particular attention is required so as to ensure
your safety and to avoid product damage. Observe
the instructions in these warnings where indicated.
SAFETY
To prevent accidents, read through the following items
before starting work, and always regard safety when
working. It is your responsibility to ensure your safety on
the job.
1. Preparations
(1) Select a work site which is level, has sufficient
space, and is not close to dangerous objects.
(2) Avoid poorly ventilated
rooms.
Asphyxiation from exhaust
fumes is always a possibility
that accompanies running an
engine.
(3) Working clothes which may
be pinched or caught in the
equipment must not be worn.
Loose clothing can cause
serious injury or death.
(4) Always wear a mask and
protective goggles during
work when dust or flying
debris may be thrown by
equipment.
2. Assembly and adjustments
(1) Before assembling
equipment, read the
assembly instructions for the
product to become familiar
with the equipment and
procedures.
(2) Use only adequate and
required equipment, tools
and instruments (e.g. torque
wrench, battery hydrometer
and etc.).
(3) Set the parking brake and
block wheels to prevent
machine (or tractor)
movement.
(4) Lower the attachment or
implement to the ground
before assembling or
adjusting equipment.
(5) Before working under
suspended or raised
equipment, support the
equipment or attachment
and utilize the valve lock to
prevent the machine from
falling or moving out of place.
(6) Keep fire from cigarettes,
matches or other ignition
sources away from fuel, oil,
antifreeze and other
flammable materials.
Indicates an imminently
hazardous situation which, if not
avoided, will result in death or
serious injury.
Indicates a potentially
hazardous situation which, if not
avoided, could result in death or
serious injury.
Indicates a potentially
hazardous situation which, if not
avoided, may result in minor or
moderate injury.
Indicates that equipment or
property damage could result if
instructions are not followed.
Gives helpful information
ASSEMBLY INSTRUCTIONS2
3. After assembly check
(1) Before operating or test driving the equipment,
read and understand the operator's manual.
(2) Once the equipment is fully
assembled, select a safe
place for a test run. Prevent
onlookers from approaching
the equipment.
To avoid personal injury or
death:
A Do not start engine or
operate levers from
anywhere other than the
seat.
To avoid personal injury:
A Do not bypass-start the
equipment. Short circuiting
the starter terminal runs the
risk that the equipment will
start operating or moving
unexpectedly.
UNPACKING AND CHECKING PARTS
BUnpacking Iron Crate
1. Cut off the vinyl ropes that secure the top of the ROPS
to the iron crate.
2. Take the diagonal member out of the front of the iron
crate.
3. Take the 4 pieces of bolts (M10-1.25) out of both side
of the iron crate.
4. Tie up the iron crate with a nylon band and lift up with
a hoist or fork lift. (Be careful not to damage the
tractor.)
BThe Accessories Packaged Together with
Tractor
A : B1220 / B : B1620, B1820 / C : B1820ACE
A FRONT / REAR TIRES are not included in crate.
No. DESCRIPTION
UNIT
ABC
1 STEERING WHEEL 1 1 1
2 ACCESSORY CASE 1 1 1
3 FENDER L/R 1 1 1
4SEAT 1 - 1
5 TOOL BOX - - 1
3ASSEMBLY INSTRUCTIONS
BContents of Accessory Case
A : B1220 / B : B1620, B1820 / C : B1820ACE
No. DESCRIPTION
UNIT
No. DESCRIPTION
UNIT
ABC ABC
1
OPERATOR'S MANUAL 1 1 1 12 LICENSE PLATE HOLDER - 1 -
WARRANTY STATEMENT 1 1 1 13 LIGHT ASSY. (LICENSE) - 1 -
ASSEMBLY INSTRUCTIONS 1 1 1 14 STAY (TRAILER SOCKET) - 1 -
SLOW BLOW FUSE 1 1 1 15 LIGHT ASSY. (COMB. FRONT) - 2 -
STARTER KEY 2 2 2 16 STAY (FRONT WINKER) - 2 -
2 HUB ASSY. 2 2 2
17
GRIP (YELLOW 83) 1 1 1
3 COVER (FENDER TAIL) - 2 - GRIP (BLACK 83) 1 1 1
4 TAIL COVER ASSY. 2 - 2 GRIP (ORANGE 63) 1 2 2
5
LIGHT ASSY. (COMB. REAR RH) - 1 - LEVER GRIP (MAIN GEAR SHIFT) 1 1 1
LIGHT ASSY. (COMB. REAR LH) - 1 - 18 SEAT UPPER SUPPORT - 2 -
6
STAY (TAIL COVER RH) 1 - 1 19 LICENSE HOLDER STAY - 1 -
STAY (TAIL COVER LH) 1 - 1
20
SEAT STAY RH 1 - 1
7
STAY (TAIL LIGHT COVER RH) - 1 - SEAT STAY LH 1 - 1
STAY (TAIL LIGHT COVER LH) - 1 - 21 SEAT COVER, OPC 1 - -
8 COVER (PTO) 1 1 1 22 PLATE, CHECK 1 1 1
9 COVER (FENDER) 2 2 2 23 STAY (LICENSE LIGHT) - 1 -
10 PAD (STEERING) 1 1 1 24 LIGHT ASSY. (HAZARD) - - 2
11
REAR FENDER STAY RH 1 - 1 25 STAY (TOOL BOX) - - 1
REAR FENDER STAY LH 1 - 1 26 DRAWBAR PIN ASSY. - - 1
4 ASSEMBLY INSTRUCTIONS
A : B1220 / B : B1620, B1820 / C : B1820ACE
No. DESCRIPTION
UNIT
No. DESCRIPTION
UNIT
ABC ABC
FRONT TIRE ACCESSORIES B1620/B1820 ACCESSORIES 2
1NUT (M12) 121212
8
BOLT (M8 x 20) - 2 -
HUB ACCESSORIES SPRING WASHER (M5) - 5 -
2 BOLT (M16 x 95) 2 2 2 PAN HEAD SCREW (M5 x 30) - 3 -
3
COTTER (2) 2 2 2 PAN HEAD SCREW (M5 x 10) - 2 -
COTTER (1) 2 2 2 FLANGE NUT (M6) - 8 -
4
SPRING WASHER (M16) 2 2 2 B1620/B1820 ACCESSORIES 3
NUT (M16) 222
9
NUT (M5) - 5 -
WHEEL TUBE PIN 2 2 2 BOLT (M8 x 20) - 3 -
SPRING PIN 2 2 2 BOLT (M6 x 16) - 1 -
5
NUT (M14) 12 12 12 PAN HEAD SCREW (M5 x 16) - 2 -
SPRINT WASHER (M14) 12 12 12 FLANGE NUT (M5) - 2 -
PLAIN WASHER (M14) 12 12 12 B1820ACE ACCESSORIES
B1220 ACCESSORIES
10
BOLT (M8 x 20) for SEAT STAY - - 4
6
TAPPING SCREW (6 x 16) 4 - - BOLT (M8 x 20) for FENDER STAY - - 4
BOLT (M8 x 20) 6 - - SNAP PIN - - 1
FLANGE NUT (M8) 4 - - FLANGE NUT (M8) - - 4
BOLT (M8 x 25) 4 - - BOLT (M8 x 25) - - 4
SNAP PIN 1 - - TAPPING SCREW (M6 x 10) - - 8
BOLT (M6 x 12) 2 - - BOLT (M6 x 16) - - 1
SEMS BOLT (M8 x20) 4 - - BOLT (M6 x 20) - - 2
BOLT (M6 x 16) 1 - - TOOL ACCESSORIES
B1620/B1820 ACCESSORIES 1
11
GREASE GUN - - 1
7
BOLT (M8 x 25) - 4 - SPANNER (10 - 12 mm) - - 1
BOLT (M8 x 20) - 9 - SPANNER (12 - 14 mm) - - 1
SCREW SEMS (M6 x 14) - 4 - SPANNER (14 - 17 mm) - - 1
FLANGE NUT (M8) - 1 - SPANNER (19 - 22 mm) - - 1
5ASSEMBLY INSTRUCTIONS
BContents of Nylon Bag Attached with the
Accessory Case
A : B1220 / B : B1620, B1820 / C : B1820ACE
ASSEMBLY
BRemoving the Battery
Take out the battery.
Charge the battery as indicated in the operator's manual.
To avoid personal injury:
A Thoroughly read the Operator's manual before
charging.
A Insufficient charging will cause the battery to run down
quickly, resulting in premature battery failure.
No. DESCRIPTION
UNIT
ABC
1
RING 222
JOINT PIN 2 2 2
BOLT (M8 x 20) for FENDER 8 8 8
3-POINT HITCH LOWERING
SPEED KNOB
111
ASSEMBLY INSTRUCTIONS6
BMounting the Right and Left Fenders
1. Move the left-side two levers of the tractor to the low
position.
2. Tilt the front of the left-hand fender (1), insert the two
levers (2) in the lever guide (3).
3. For the right-hand fender, insert the levers in the lever
guide.
4. Secure the fender (LH and RH) (1) with the four M8
bolts (2).
BInstalling the Lever Grip
Install the lever grips onto the control levers. See the
figure.
A Apply rubber-bonding adhesive to the lever before
installing the lever grips to permanently secure them.
BAttaching the 3-Point Hitch Assembly
1. Attach the top link (1) to the top link bracket (2) with the
joint pin and the set pin.
A The upper hole on the top link bracket (2) is normally
used for mounting.
2. Attach the lift rod (3) to the lift arm (4) with the joint pin
and snap ring.
3. Grease all screws and rotating parts of the 3-point
hitch until movement is smooth.
(1) Yellow 83
(2) Orange 63
(3) Lever grip (main gear shift )
(4) Orange 63 [B1620, B1820, B1820ACE]
(5) Black 83
7ASSEMBLY INSTRUCTIONS
BAttaching the Fender Cover
1. Install the fender cover (1) on the right and left fenders.
BAttaching the Tail Cover and Rear Fender
Stay
[B1220]
1. Secure the tail light cover stay (LH and RH) (1) to their
respective tail light covers (2) with two tapping screws
(3).
2. Insert the cord clamp of wire harness (1) into the hole
(A) of the fender (RH).
3. Attach the rear fender stay (1) to the fender (LH and
RH) with the M8 x 20 bolt (2).
4. Align the hole of the tail cover stay (3) with that of the
fender and rear fender stay.
Secure the tail cover (4) tightening the M8 x 20 bolt (5)
and M8 nut (6).
ASSEMBLY INSTRUCTIONS8
BAttaching the Tail Light and License
Holder Stay
[B1620, B1820]
1. Attach the tail light (1) to the tail light cover (2).
2. Attach the tail light stay (3) to the tail light cover (2) with
the nuts (4) and tighten them.
3. Install the tail light assembly (1) and license holder
stay (2) at the right or left rear of the tractor with the M8
x 20 bolts (3), M8 nut (4).
4. Install the tail light assembly (1) with the M8 x 20 bolt
(2) to the right rear of the tractor.
5. Connect the rear combination light cables to the wire
harness cables with the 4-P coupler (1). (Both sides)
Insert the cord clamp of wire harness into the hole (A)
of tail light stay (RH and LH).
6. Insert the cord clamp of wire harness (1) into the hole
(A) of fender (RH and LH).
9ASSEMBLY INSTRUCTIONS
BAttaching the Tail Light, Rear Fender Stay
and the Turn Signal/Hazard Light
[B1820ACE]
1. Insert the rear turn signal / hazard light (1) into the hole
of the fender.
Secure the light with plain washer (2), spring washer
(3) and nut (4).
2. Secure the right-hand and left-hand tail cover stays (1)
to their respective tail lights (2) with the four tapping
screws (3).
Attach the cord clamp of wire harness to the hole (A).
3. Attach the rear fender stay (1) to the fender (LH and
RH) with the M8 x 20 bolt (2) and M8 flange nut (3).
4. Align the hole of the tail cover stay (4) with that of the
fender and rear fender stay.
Secure the tail cover (5) tightening the M8 x 20 bolt (6)
and M8 flange nut (7).
5. Connect the tail light cable to the wire harness cable
with the 1-P coupler (8).
6. Connect the rear turn signal / hazard light cables to the
wire harness cables with the 1-P coupler (3).
A Make sure of the cable combination of the tail light and
side turn signal / hazard light cables and their partner
couplers. Confirm the color of the couplers.
7. Insert the cord clamp of wire harness (1) into the hole
(A) of the fender (RH and LH).
ASSEMBLY INSTRUCTIONS10
BAttaching the Front Combination Light
[B1620, B1820]
1. Attach the front winker stay (1) with the M6 x 14 bolts
(2) and M6 flange nuts (3).
2. Pass the combination light cable through the hole of
the center pillar.
A Install the front turn signal / hazard light at the upper
position.
3. Attach the combination light (1) to the front winker stay
(3) with the M6 flange nuts (2).
4. Connect the combination light cables to the wire
harness cable with the 1-P coupler (1).
A When connecting the cables, pass the cable (2)
without being touched by the rod (3).
11ASSEMBLY INSTRUCTIONS
BAttaching the License Light and Trailer
Electrical Outlet
[B1620, B1820]
1. Attach the license light (2) to the license light stay (1)
with the washers and nuts (3).
2. Attach the license light stay (1) to the license plate
holder (4) with the two M5 x 16 pan head screws (5)
and two flange nuts (6).
3. Attach the license plate holder (4) to the license holder
stay (7) with the M8 x 20 bolts (8).
4. Connect the license light cables to the wire harness
cables with the 1-P coupler (9).
A When attaching the license light (2), apply the ground
(10) between the license plate holder (4) and the
flange nut (6) as shown below.
5. Attach the trailer electrical outlet (1) to the trailer
socket stay (5) with the pan head screw (2), nuts (3),
and spring washers (4).
6. Attach the trailer electrical outlet (1) to the license plate
holder (4) with the M5 screws (2), M5 nuts (3) and
spring washers (4).
BAttaching the Steering Wheel
1. Attach the steering wheel (1) with one M12 nut (2) and
spring washer (3). The steering wheel should sit flat on
the steering column and be positioned as shown in the
photo.
2. Tightening torque for the M12 nut (2) should be 30 to
49 N-m (3.0 to 5.0 kgf-m).
3. Attach the pad (4).
ASSEMBLY INSTRUCTIONS12
BAttaching the Seat
[B1220, B1820ACE]
1. Attach the seat stays (2) to the seat (1).
2. Attach the seat (1) and set the snap pin (3).
3. Apply the OPC seat cover (4) to the seat (1) with the
bolts (5). [B1220]
[B1620, B1820]
1. Attach the upper seat support (1) to the seat with the
two M8 x 20 bolts (2).
2. Place the seat on the tractor and fix it with five M8 x 20
bolts (1).
BAttaching the Check Plate
1. Attach the check plate (1) with the M6 x 16 bolt (2).
A Make sure the hole of the check plate (1) is placed
forward.
BAttaching the PTO Cover
1. Attach the PTO cover (1) to the lower link stay and
tighten them with four M8 x 25 bolts (2).
13ASSEMBLY INSTRUCTIONS
BHoisting the Tractor
To avoid personal injury:
A Set blocks and/or safety stands under the
tractor when suspended, to prevent falling,
before working under neath.
C Hoist and jigs
1. Use a 1 ton or larger hoist.
2. Use belt straps to protect the painted surfaces from
scratches.
3. Prepare blocks and safety stands.
C Hoist hook position
Never raise the front and rear ends at the same time.
A Front end: Fit the front hitch to the front bumper with
the four bolts. Lift the assembly as shown in the figure.
A Suspend the front jig, place a safety stands below and
put the jig on the safety stands.
A Rear end : Hook to ROPS as indicated in the figure.
BAttaching the Front Tires
1. Attach the front tires (1) (left and right) with twelve M12
nuts (2).
A Be sure the inflation valve stem of each tire faces
outward.
2. Tightening torque for the M12 nuts (2), should be 79.0
to 92.0 N-m (8.1 to 9.4 kgf-m, 58.3 to 67.9 ft-lbs).
3. Check air pressure in the front tires.
4. Remove the front jig.
A Refer to the Operator's Manual for the proper air
pressure.
ASSEMBLY INSTRUCTIONS14
BAttaching the Rear Tires
1. Attach the left and right hub (1) to the rear tires with six
M14 nuts (2), spring washers (3) and plain washers (4)
each.
A If the tire side wheel is made for taper nut mounting,
use only the nut and tighten with the taper side.
A Be sure the hubs are facing in the proper direction.
2. Tightening torque for the M14 nuts (2) should be 108
to 126 N-m (11.0 to 12.8 kgf-m).
3. Hook a hoist to the tractor's 3-point hitch and lift the
tractor.
4. Pull out the crate skids from the rear.
5. Insert the rear tire assembly over the axle, to the
desired tread setting: then attach the wheel tube pin
(5) and spring pin (6) and tighten the M16 nut (7), M16
spring washer (9) and M16 bolt (8).
6. Tightening torque for the M16 nut (7) should be 124 to
147 N-m (12.6 to 15.0 kgf-m).
7. The standard position of the rim on the axle is as
shown in the figure below.
8. Check air pressure in the rear tires.
A Refer to the Operator's Manual for the proper air
pressure.
A Insert the bolt from the indented side of the cotter (A)
as shown.
15ASSEMBLY INSTRUCTIONS
BHooking up the Battery
1. Perform the following after the battery has received a
good charge (specific gravity: 1.26/20 C).
(1) Check that the battery fluid is at an intermediate
point between the upper and lower level
markings.
(2) Wipe the battery clean of any battery fluid on the
outside. (Battery should be washed clean with
water so no acid is left on battery case.)
2. Next, mount the battery (1) on the mounting plate (2).
while doing so, make sure the two rubber plates are in
the correct position (see figure below).
3. Fix the battery (1) in place with the battery retainer (3),
the battery set bolt (4), the M6 plain washer (5) and the
wing nut (6).
4. Connect the (+) cable first, then the (-) cable.
5. Apply a moderate amount of grease to the battery
terminals.
A Always connect the (+) cable of the battery before the
(-) cable.
Connecting the (-) cable first runs the risk of short
circuit while connecting the (+) cable.
BAttaching the Tool Box
[B1820ACE]
1. Remove the M8 x 20 bolt (1).
2. Attach the tool box stay (2) to the seat support (3) with
the M8 x 20 bolt (1).
3. Attach the tool box (5) to the tool box stay (2) with the
two M6 x 20 bolt (4).
ADJUSTING THE HEAD LIGHT
ALIGNMENT
[B1620, B1820]
1. Adjust the head light alignment turning the screws (1).
16 ASSEMBLY INSTRUCTIONS
CHECKING LIST FOR INSPECTION AFTER ASSEMBLY
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
Kubota B1220 Assembly Instructions Manual
- Type
- Assembly Instructions Manual
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
Kubota B1620 Workshop Manual
-
-
-
-
-
-
-
-
-
Other documents
-
DV8 OFFROAD FDJL-01 Installation guide
-
Sharp LB1085 User manual
-
Harbor Freight Tools 1720 lb. Capacity 48 in. x 96 in. Super Duty Trailer User manual
-
HAUL MASTER 94564 Assembly And Operating Instructions Manual
-
Yamaha FZ-16 Assembly Manual
-
DAELIM VJF125 User manual
-
wsm M9540NARROW Workshop Manual
-
Cub Cadet 7254 User manual
-
-
Baja WD400U User manual
