Kubota GZD21-2 HD Assembly Manual

Brand: Kubota

Model: GZD21-2 HD

Type: Assembly Manual

This manual is also suitable for

ENGLISH

FRANÇAISDEUTSCH

MONTAGEANLEITUNG

ASSEMBLY

INSTRUCTIONS

INSTRUCTIONS DE

MONTAGE

1BDABANAP2170

MODELS

MODELES

MODELLE

GZD15-3 LD/HD

GZD21-2 HD

PRINTED IN JAPAN

IMPRIME AU JAPON

DRUCK : JAPAN

Code No.

AT . B . 2 - 3 . 2 . AK N

de code. K2013-7152-2

Code Nr.

KUBOTA Corporation 2014

TO THE DEALER

This manual contains procedures intended to assist the dealer in unpacking and

assembling the product before delivering to the customer.

The customer's purchase is based on condence in both the product and your

store. Observe the procedures in this manual to assemble and adjust equipment for

your customer's safety and satisfaction. When fully assembled, check function of

each part and feature.

SAFETY FIRST

The following safety alert symbol marks and indication are found throughout this

manual in steps where particular attention is required so as to ensure your safety

and to avoid product damage. Observe the instructions in these warnings where

indicated.

DANGER : Indicates an imminently hazardous situation which, if not

avoided, will result in death or serious injury.

WARNING : Indicates a potentially hazardous situation which, if not

avoided, could result in death or serious injury.

CAUTION : Indicates a potentially hazardous situation which, if not

avoided, could result in minor or moderate injury.

IMPORTANT : Indicates that equipment or property damage could result if

instructions are not followed.

NOTE : Gives helpful information.

AU REVENDEUR

Ce manuel contient les procédures prévues pour aider le revendeur monter le

produit avant la livraison au client.

L'achat du client est basé sur la conance qu'il accorde au produit et à votre

magasin. Respecter la procédure décrite dans ce manuel et régler l'équipement

pour la sécurité de votre client. Lorsque le montage est terminé, vérier le bon

fonctionnement de chaque pièce et caractéristique.

Pour vos clients qui parlent français, joindre l'étiquette en français qui se trouve

dans l'emballage des accessoires.

LA SECURITE EN PREMIER LIEU

Le symbole et les indications de sécurité suivants se trouvent dans ce manuel

lorsqu'une attention particulière est requise pour assurer la sécurité en cours

d'utilisation et éviter d'endommager le produit. Respecter les instructions données

dans ces avertissements.

DANGER : Indique une situation éminemment dangereuse. Des

blessures graves ou la mort peuvent survenir si cette

situation n'est pas évitée.

AVERTISSEMENT : Indique une situation potentiellement dangereuse. Des

blessures graves ou la mort peuvent survenir si cette

situation n'est pas évitée.

ATTENTION : Indique une situation potentiellement dangereuse. Des

blessures mineures ou graves peuvent survenir si cette

situation n'est pas évitée.

IMPORTANT : Si les instructions se sont pas suivies, l'équipement ou

vos biens peuvent être endommagés.

NOTE : Donne des informations pertinentes.

AN DEN HÄNDLER

Diese Anleitung beinhaltet Verfahrensschritte, die dem Händler beim Zusammenbau

des Produkts helfen sollen, bevor es an den Kunden ausgeliefert wird.

Der Kauf durch den Kunden basiert auf dem Vertrauen des Kunden am Gerät und

Ihrem Geschäft. Beachten Sie bitte die Verfahrensschritte in dieser Anleitung um

den Zusammenbau und die Einstellung am Gerät zur vollsten Zufriedenheit des

Kunden durchzuführen. Nach dem Zusammenbau ist das Gerät auf sämtliche

Funktionen zu überprüfen.

SICHERHEIT KOMMT ZUERST

Das folgende Sicherheits-Warnsymbol ist vom Anfang bis zum Ende in dieser

Bedienungsanleitung an den Stellen zu nden, wo spezielle Vorsicht geboten

ist, die die Sicherheit des Bedieners sowie die Sicherheit der sich in der Nähe

bendlichen Personen betrifft, und um Schaden am Gerät zu vermeiden. Befolgen

Sie deshalb diese Warnhinweise in den bezeichneten Abschnitten.

GEFAHR : Dieses Zeichen weist auf die Möglichkeit einer äußerst

gefährlichen Situation hin, die zu einem schweren Unfall

führen kann, wenn sie nicht vermieden wird.

WARNUNG : Dieses Zeichen warnt davor, keine gefährlichen Situationen

einzugehen, die zu schweren Unfällen führen können.

VORSICHT : Dieses Zeichen macht Sie darauf aufmerksam, dass es

durch unaufmerksames Verhalten zu Unfällen kommen kann.

WICHTIG : Diese Überschrift macht Sie darauf aufmerksam, die

entsprechenden Hinweise der Anleitung zu beachten, damit

es nicht zu Beschädigungen von Mäher und Anbaugeräten

kommen kann.

HINWEIS : Unter dieser Überschrift nden Sie wichtige Informationen.

ENGLISH

SAFETY

To prevent accidents, read through the following items

before starting work, and always regard safety when

working. It is your responsibility to ensure your safety on

the job.

1. Preparations

(1) Select a work site which is level, sufficiently

spacious and not in the vicinity of dangerous

objects.

(2) Avoid poorly ventilated rooms. Asphyxiation from

exhaust fumes is always a possibility that

accompanies running engine.

(3) Working clothes which may be pinched or caught

in the equipment must not be worn. Loose

clothing can cause serious injury or death.

(4) Always wear a mask and protective goggles

during work when dust or flying debris is thrown

about.

2. Assembly and adjustments

(1) Before assembling equipment, read the assembly

instructions for the product to become familiar

with the equipment and procedures.

(2) Use only adequate and required equipment, tools

and instruments (torque wrench or battery

hydrometer).

(3) Set the parking brake and place blocks in front of

wheels (when they're contacting the ground) to

prevent machine movement.

(4) Lower the attachment or implement to the ground

before assembling or adjusting equipment.

(5) Before working under suspended or raised

equipment, support the equipment or attachment

to prevent the machine from falling or moving out

of place.

(6) Keep fire from cigarettes, matches or other

ignition sources away from fuel, oil, antifreeze and

other flammable materials.

3. After assembly check

(1) Once the equipment is fully assembled, select a

safe place for a test run. Prevent onlookers from

approaching the equipment.

To avoid serious injury or death:

A Do not start engine or operate levers from

anywhere other than the seat.

To avoid serious injury or death:

A Do not bypass-start the equipment. Short

circuiting the starter terminal runs the risk that

the equipment will start operating or moving

unexpectedly.

ENGLISH

UNPACKING AND CHECKING PARTS

BUNPACKING WOODEN CRATE

1. Hook a hoist to the 4 corners of the crate and raise the

hoist cable until taut.

This serves to prevent the upper part of the crate from

striking the machine when cut.

2. Saw the crate as indicated in the figure below.

A Sawing outside the indicated area may damage the

machine or accessory parts.

A Be sure that the crate is free of other obstructions (e.g.

nails, staples and etc.).

3. Raise the upper part of crate and remove from the

immediate area.

4. Remove the remaining slats from the crate.

These are indicated by the oblique lines in Figure 1.

BUNPACKING IRON CRATE

1. Hook nylon ropes at the four corners of the iron-crate's

top stay. Pull up the nylon ropes until they get just tight.

2. Remove the six bolts from behind the vertical supports

on both sides of the iron crate.

3. Lift and detach the top frame of the iron crate.

A In lifting the top frame, be careful to keep the crate's

vertical supports from scratching the machine.

Figure 1: Cutting area of the crate

(1) Nylon band (A) Front

(B) 300 mm

(1) Nylon band

(2) 6-Bolt

(3) Iron crate

(1) Iron crate

ENGLISH

4. Unlocking both ends of the rear axle

Remove the snap pins off both ends of the rear axle,

and draw out the headed pins.

5. Remove the fixtures (1), (2), (3), (4) from the machine

front as shown in the figure below.

Join the fixtures (1), (3), (4) to the iron crate bottom.

(1) Snap pin

(2) Headed pin

(1) Stay

(2) Nut

(3) Bolt

(4) Nut

ENGLISH

BTHE ACCESSORIES PACKAGED

TOGETHER WITH GZD15-3 AND GZD21-2

REF.

No.

PART NAME Q'TY

GZD15-3 GZD21-2

LD HD HD

(1)

400BAG, ASSY 1 ---

500BAG, ASSY 1 --- ---

(2) 400COVER, ASSY 1

(3)

ARM (LIFT, UPPER) 2 ---

ARM (LIFT, LOWER) 2 ---

(4)

PART, SHIPPED, KIT 1 --- ---

(5)

ACCESSORIES,

ASSY (Bag)

1 --- ---

(6) COVER (LH) 1 ---

(7) PIPE (ROPS) 1

(8) PIPE (ROPS UPPER) 1

(9) RC42GZD-3, MOWER 1 ---

(10)

RCK48GZD-2,

MOWER

1 --- ---

ENGLISH

BACCESSORIES ASSY

<Box>

REF.

NO.

PART No. PART NAME

QUANTITY

RE-

MARKS

GZD

15-3

GZD

15-3

GZD

21-2

(1) K2013-7122-0

MANUAL,

111

(2) K2013-7152-2

MANUAL,

INST

111

(3) PL501-6892-0

KEY,

STARTER

111

(4)

K2011-1813-0

BOLT,

HEX (M12 x

1.25 x 210)

222

M12 x

210

02572-50120

NUT,

LOCKING

222M12

(5) K2011-6550-4

SET LABEL,

MAINTE.

111

(6)

01133-51225

BOLT,

SEMS

888

M12 x

01123-50825

BOLT,

SEMS

111M8 x 25

(7)

K2013-2141-0

BOLT,

FLANGE

(M8 E 26)

4 4 --- M8 x 26

01754-50816

BOLT,

FLANGE

4 4 --- M8 x 16

K3655-5221-0

WASHER

(BOLT)

4 4 ---

04613-50050

CIR-CLIP,

EXTERNAL

6 6 ---

(8)

K2013-2138-0

PLATE

(LH 2)

1 1 ---

K2013-2142-0

PLATE

(BOLT

HOLDER 16)

4 4 ---

K2013-2143-0

BOLT,

FLANGE

(M8 E 35)

2 2 --- M8 x 35

(9) K2031-8616-0

BOLT

(M16 x 2)

222

M16 x

147

(10)

K3611-8256-0 NUT 2 2 2 M16

01133-51020

BOLT,

SEMS

111

M10 x

04512-50100

WASHER,

SPRING

LOCK

333

02572-50100

NUT,

LOCKING

333M10

ENGLISH

<Bag>

REF.

NO.

PART No. PART NAME

QUANTITY

RE-

MARKS

GZD

15-3

GZD

15-3

GZD

21-2

(11)

01133-51000

BOLT,

SEMS

222

M10 x

100

04512-50100

WASHER,

SPRING

LOCK

222

02118-50100 HEX. NUT 2 2 2 M10

01615-51025

BOLT,

CUP-SQ-NK

222

M10 x

(12) K2031-8615-0

PIN (LOCK),

SET

222

(13) K2013-5681-2

SUPPORT

(SEAT

BELT)

111

(14)

K6082-6353-0

COLLAR,

ARM

--- 8 8

01173-51470 HEX. BOLT --- 7 7

M14 x

02574-50140

NUT,

LOCKING

--- 7 7 M14

04011-50140

WASHER,

PLAIN

--- 11 11

(15) K5243-3203-0

ASSY

JOINT,

UNIVERSAL

11---

(16) K2771-5685-2

BELT,

SEAT, ASSY

111

(17) K5245-7271-3

COVER

(CENTER)

11---

(18) K5245-7269-2

COVER

(CENTER

LH)

11---

(19) K2013-2134-0

COVER

(U/J)

11---

(20) K2031-5351-4

GUARD

(FRONT)

111

(21) 01138-51430

BOLT,

SEMS

888

REF.

No.

PART NAME

QUANTITY

RE-

MARKS

GZD21-2

(1)

UNIVERSAL JOINT

COVER FRONT STAY

(2)

BOLT (for Universal

joint cover front stay)

2 M8 x 16

ENGLISH

ASSEMBLY OF THE GRASS CATCHER

CONTAINER

BPreparations for Assembling the Under

ROPS Pipe

1. Make a team of two to do this job.

2. Remove the bolt (1) and nut (2) from the lift rod (for

both sides).

The bolt (1) will be used again to reassemble this

component. Be careful not to lose them. (The nut (2)

will not be reused.)

BInstalling the Under ROPS Pipe

1. Remove the snap pin (1) that keeps the cylinder (A) in

place.

2. Remove the 4 bolts (2) first and then the fixing plate

(1). (The same for both sides)

4 bolts (2) will not be reused.

3. Using the bolts (3), temporarily connect the pipes

(ROPS, UNDER) (1) to the frame (3). (4 bolts each for

each side)

Fix the cylinder (2) to the frame (A) with the headed pin

(4) and snap pin (5).

(1) Bolt

(2) Nut

(3) Lift rod

(4) Under ROPS pipe

(1) Snap pin (A) Cylinder

(1) Fixing plate

(2) Bolt

(A) PIPE, ROPS UNDER

(B) Frame

(1) PIPE, ROPS UNDER

(2) Cylinder

(3) Bolt (M14 x 30)

(4) Headed pin

(5) Snap pin

(A) Frame

ENGLISH

BInstalling the Lift Arms (Upper and Lower)

A There are two upper lift arms. The lift arm that has a

stay is for the right side. Be careful not to confuse the

right and left ones and to keep the stay outward.

C Under ROPS pipe side

Using bolts, washers, collars and nuts, install the upper lift

arm and the lower lift arm to PIPE, ROPS UNDER.

Tightening torque: 40 to 50 N-m (4.1 to 5.1 kgf-m)

A Set the washer on the nut side. Insert the bolt from the

outside. For the lower lift arm, set the cylinder

mounting bracket downward

A Apply grease between the lift arm and PIPE, ROPS

UNDER.

C Bag base side

(Right side lower lift arm)

1. Remove the headed pins and take off the arm cam

from the bag base.

2. At the right side, using the arm cam, collars and

washers, install the lower lift arm.

3. Fix the arm cam with the headed pin and the snap pin.

A Set the washers on the inside of the bag base only.

(1) Bag base

(2) PIPE, ROPS UNDER

(3) Upper lift arm

(4) Lower lift arm

(5) Cylinder mounting bracket

(6) Stay

(1) Bolt (M14 x 70)

(2) Washer

(3) Collar

(4) Nut (M14)

(5) Upper lift arm

(6) Lower lift arm

(7) PIPE, ROPS UNDER

(1) Headed pin

(2) Snap pin

(3) Washer

(4) Bag base

(1) Arm cam

(2) Collar

(3) Lower lift arm

(4) Bag base

ENGLISH

(Left side lower lift arm)

Using bolts, washers, collars and nuts, install the lower lift

arm to the bag base.

Tightening torque: 40 to 50 N-m (4.1 to 5.1 kgf-m)

A Set the washers on both sides. Insert the bolt from the

outside.

A Apply grease between the lift arm and the bag base.

(Upper lift arm)

The position of the hole for setting is different between

GZD15-3 and GZD21-2.

Using bolts, washers, collars and nuts, install the upper lift

arms to the bag base.

Tightening torque: 40 to 50 N-m (4.1 to 5.1 kgf-m)

A Set washer on both sides. Insert the bolt from the

outside. (Same as the left side lower lift arm.)

A Apply grease between the lift arm and the bag base.

BInstalling the Lift Rod

Temporarily fix the lift rod (2) to PIPE, ROPS UNDER (1)

with the M10 x 16 bolts (3) on both sides. Tighten up the

bolts.

Tightening torque: 48.1 to 55.9 N-m (4.9 to 5.7 kgf-m)

BInstalling the Cylinder

Using the headed pin (3) and snap pin (4), connect the

cylinder (2) to the lower lift arm (1).

(1) Bolt (M14 x 70)

(2) Washer

(3) Collar

(4) Nut (M14)

(5) Lower lift arm

(6) Bag base

(1) Bolt (M14 x 70)

(2) Upper lift arm

(3) Bag base

(A) for GZD15-3

(B) for GZD21-2

(1) PIPE, ROPS UNDER

(2) Lift rod

(3) M10 x 16 bolt

(A) For GZD21-2

(B) For GZD15-3

(1) Lower lift arm

(2) Cylinder

(3) Headed pin

(4) Snap pin

ENGLISH

BTightening the Bolts

Tighten up the M14 x 30 bolts (2) (4 pcs. for each side) to

the frame.

Tightening torque: 123.6 to 147.0 N-m (12.6 to 15.0 kgf-

BInstalling the ROPS Pipe

Use M10 flange bolts and flange nuts to install PIPE

(ROPS) to PIPE, ROPS UNDER as shown in the figure

below.

Tightening torque: 48.1 to 55.9 N-m (4.9 to 5.7 kgf-m)

BGZD15-3 HD & GZD21-2 HD Hose Clamp

Positions

A Lift the back base to its top limit and clamp it tightly.

A Make sure the hoses are parallel, not crossing each

other.

A Make sure that the hoses are clamped on the upper lift

arm.

A Move up and down the back base to make sure that

the hoses do not stretch tight (P), nor come into

contact with the lift base and rear tires (Q).

A Be sure to pass the clamp through the Under ROPS

pipe stay and to clamp the hoses. (R)

A Be sure to clamp the sleeve ends of the hoses. (S)

A Be sure to clamp the white-taped zone of the hoses

above the cylinders. (T)

A Be sure to clamp the hoses below the top of the

fenders. (U)

(1) PIPE, ROPS UNDER

(2) Bolt (M14 x 30)

(1) PIPE, ROPS

(2) Flange bolt (M10)

(3) Flange nut (M10)

(A) PIPE, ROPS UNDER

(1) Upper lift arm

(2) Clamp on the bag base

(3) Clamp on the lift cylinder

(4) Clamp below the fender's

top level

(5) Clamp above the check wire

stay level

(6) Clamp on the upper lift arm

(A) Pass close to the headed

(B) 200 mm (reference)

(D) 200 mm (reference)

ENGLISH

Assemble the grass catcher container by referring to

GC400HZ grass catcher instruction manual.

INSTALLATION OF TIRE, MOWER, LABEL,

LOW DUMP GRASS CATCHER AND SO ON

BPutting the Tires

1. Lifting the machine

For the front, apply nylon slings around the front axle.

For the rear, apply nylon slings around the right and

left frames.

2. Putting the front tires

Fix the tire (1) to the front axle with the bolt (2) and nut (3).

Tightening torque: 20 to 25 N-m (2.0 to 2.5 kgf-m)

A When removing the hubcap from the front wheel, be

careful not to drop and lose the collar.

A Direct the wheel bracket backwards and place the tire

(1) with the air valve outwards, as shown below.

A Turn the front tire by hand to make sure it turns

smoothly.

A Insert the bolt (2) from outside and apply the nut (3)

inside.

A Tighten the nut gradually until wheel bearing play is

eliminated and wheel turns freely by hand.

3. Putting the rear tires

Fix the tire (1) to the rear axle with the bolts (2) (4 pcs. for

each side).

Tightening torque: 77.5 to 90.2 N-m (7.9 to 9.2 kgf-m)

A For the tire pressure, refer to the Operator's Manual.

A Place the tire (1) with the air valve outwards.

(1) Tire

(2) Bolt (M12 x 210)

(3) Nut (M12)

(A) Wheel bracket

(B) Air valve

(1) Tire

(2) Bolt

ENGLISH

BInstalling the Upper ROPS Pipe

Use 2 set pin assies, locking nuts and bolts to install PIPE,

ROPS UPPER (1) to PIPE, ROPS UNDER.

Tightening torque: 50.0 to 60.0 N-m

5.1 to 6.1 kgf-m

BAdjustment of Foldable ROPS

A Adjust free fall of the ROPS upper frame regularly.

A If you feel less friction when folding the ROPS, tighten

the nut (1) until you feel the right friction in the

movement and then replace the cotter pin.

BInstalling the Front Guard

1. Remove 2 existing bolts. (These bolts will not be

used.)

2. Use 2 bolts, 2 nuts and 2 washers to install GUARD

(FRONT) to the weight bracket as shown in the figure

below.

(1) PIPE, ROPS UPPER

(2) Set pin

(3) BOLT (M16)

(4) NUT (M16)

(1) Nut

(1) Existing bolt (M10)

(1) GUARD (FRONT)

(2) Bolt (M10 x 100)

(3) Nut (M10)

(4) WASHER, SPRING

ENGLISH

BInstalling the Seat Belt Assy

As shown in the figures below, install BELT, SEAT, ASSY

(1) to the seat.

BPreparations For Attaching the Mower

Before attaching the mower, set hardware for installation

to frame and covers beforehand.

(1) BELT, SEAT, ASSY

(2) SUPPORT (SEAT BELT)

(3) SQUARE NECK BOLT (M10 x 25)

(4) BOLT (M10 x 20)

(5) Nut (M10)

(6) Washer

(A) 35 5 from

the level

(1) COVER (LH)

(2) COVER (LH 2)

(1) COVER (U/J)

(1) PLATE (BOLT HOLDER 16)

(2) Flange bolt (M8 x 16)

(3) Washer

(H) Hole

ENGLISH

BAttaching the Mower

1. Attach the mower by referring to operator's manual.

BAttaching the Label

Attach the label to the backside of a seat.

BAttaching the Grass Catcher Container

Mount the grass catcher container by referring to "GRASS

CATCHER MOUNTING" section in GZD15-3 LD/HD,

GZD21-2 HD operator's manual.

(1) Flange bolt (M12 x 26)

(2) Flange nut (M12 x 35)

(3) CIR-CLIP

(P) COVER (LH)

(Q) Frame

(R) Welded nut

(S) COVER (LH 2)

(1) Label

ENGLISH

AFTER-ASSEMBLY CHECK

1. After assembling, check the machine based on the following check list and check the safety switches.

AFTER-ASSEMBLY CHECK LIST Inspector:

Model number: Machine number: Inspection date:

Division Inspection item Results

Assembly

1. Are the front tires tightly and properly fastened?

2. Are the rear tires tightly and properly fastened?

3. Have all bolts been tightened, are there any missing parts?

4. Are the hose clamps in their specified positions? [for HD]

5. Are the hoses out of contact with the tires?

(30 mm or more clearance needed) [for HD]

Lubrication

1. Engine oil amount correct?

2. Transmission fluid amount correct?

3. Mower gear case oil amount correct?

4. Front PTO case fluid amount correct?

Cooling water

1. Radiator coolant amount correct?

2. Recovery tank filled with correct amount of coolant?

Electrical system

1. All instruments (Fuel gauge and hour meter) functioning?

2. EASY CHECKER(TM) functioning?

3. Battery cable properly connected?

4. Charged enough (proper specific gravity)?

Running

1. Parking brake well responsive?

2. Acceleration lever working smoothly?

3. HST system working smoothly?

4. Motion control levers neutral position ensured with levers out.

5. PTO on / off operation smooth?

6. Mower up / down operation smooth?

7. Key switch functioning for smooth engine stop?

8. OPC system and PTO control system functioning?

(See "Check the OPC system and PTO control system".)

Others

1. No oil leak and fuel leak?

2. Check inflation pressure of tires.

3. Does engine start system operate correctly? (See "Check the engine start system".)

4. All accessories (operator's manual, key switch, etc.) on hand?

ENGLISH

C Check the engine start system

1. Start and run the machine following all safety instructions in the operator's manuals.

2. Check the engine start system.

Check the following tests before operating the machine.

If the machine does not pass one of the following tests, do not operate the machine.

Inspection item Results

Test 1 (OPERATOR NOT ON THE SEAT)

1. Securely set the parking brake.

2. Shift the PTO lever to "DISENGAGE" (OFF) position.

3. Set the motion control levers to the "NEUTRAL LOCK" position.

4. Turn the key switch to "START" position.

5. The engine must not crank.

Test 2 (OPERATOR ON THE SEAT)

1. Do not set the parking brake. (release it from test 1)

2. Shift the PTO lever to "DISENGAGE" (OFF) position.

3. Set the motion control levers to the "NEUTRAL LOCK" position.

4. Turn the key switch to "START" position.

5. The engine must not crank.

Test 3 (OPERATOR ON THE SEAT)

1. Securely set the parking brake.

2. Shift the PTO lever to "DISENGAGE" (OFF) position.

3. Grasp the motion control levers and move them inward from "NEUTRAL LOCK" position to

"NEUTRAL" position and then release the levers.

4. Turn the key switch to "START" position.

5. The engine must not crank.

Test 4 (OPERATOR ON THE SEAT)

1. Securely set the parking brake.

2. Shift the PTO lever to "ENGAGE" (ON) position.

3. Set the motion control levers to the "NEUTRAL LOCK" position.

4. Turn the key switch to "START" position.

5. The engine must not crank.

Test 5 (OPERATOR ON THE SEAT)

1. Open the hood.

2. Sit on the operator's seat.

3. Depress the brake pedal fully.

4. Turn the key to the "START" position.

5. The engine should not crank.

Page is loading ...

Kubota GZD21-2 HD Assembly Manual

Brand: Kubota

Model: GZD21-2 HD

Type: Assembly Manual

This manual is also suitable for

Download PDF

report

in other languages

français: Kubota GZD21-2 HD
Deutsch: Kubota GZD21-2 HD

Kubota GZD21-2 HD Assembly Manual

This manual is also suitable for

Kubota GZD21-2 HD Assembly Manual

in other languages

Related papers

Other documents