Teleco Monitor 15 Technosonic LCD2018 User manual

Brand: Teleco

Model: Monitor 15 Technosonic LCD2018

Category: LCD TVs

Type: User manual

Teleco Monitor 15 Technosonic LCD2018 is a 15-inch LCD TV with a standard size of 40 cm and a visible diagonal size of 37 cm. It has a power consumption of 36 W and an operating voltage of 230 V (AC) ~50 Hz (by adapter 12 V DC). The TV system is PAL I / NTSC PLAYBACK, and the band is VHF 1 Band 2 - 4, VHF III Band 5 - 12, UHF Band 21 - 69, Band S S1-S41. The aerial input is 75 Ω (ohm) Standard Antenna Socket, and the program capacity is 100 + 3 AV. The picture tube is a TFT LCD Panel with a resolution of 1024 x 720, and the sound output rms is 2 x 2 W. The

Vers. 001

INSTALLATION GUIDE AND USER MANUAL

OF THE

TECHNOSONIC 15” LCD TV LCD2018

Technosonic LCD2018 Vers. 001

Contents

Information...........................................................................................................................3

Technical specifications.......................................................................................................4

Disposal of waste.................................................................................................................4

Mains operation...................................................................................................................5

What to do for safety of your TV..........................................................................................6

Safety information (continued).............................................................................................7

Which of your TV performs what function............................................................................8

Remote control ....................................................................................................................9

Aerial connection...............................................................................................................11

Outdoor aerial connection..............................................................................................11

VCR, DVD, Satellite decoder and computer connections...............................................12

Satellite receiver / cable TV receiver connections..........................................................13

TV Functions......................................................................................................................14

Setup .................................................................................................................................16

TV Functions (Menus)....................................................................................................17

Teletext ..........................................................................................................................22

Troubleshooting.................................................................................................................24

Vers. 001 Technosonic LCD2018

Information

Congratulations on purchasing our TV Technosonic LCD2018.

This handbook has been drawn up to provide information on installation, use, maintenance

and technical specifications for your TV:

Issue date: November 20, 2006

Document version: Technosonic LCD2018 vers. 001

Should you require further information please contact your local dealer or:

TELECO s.p.a.

Via E. Majorana 49

I-48022 LUGO (RA)

Web site: www.telecogroup.com

Technical Assistance: [email protected]

Technical Assistance: 899.899.856

TELECO s.p.a. cannot be held liable for any errors contained in this handbook. All the in-

formation contained in the handbook is updated to the date of issue document. TELECO

s.p.a. reserves the right to make modifications according to technological changes.

Technosonic LCD2018 Vers. 001

Technical specifications

Screen Size ......................................................................................................................15”

Standard Size..............................................................................................................40 cm

Visible diagonal size ....................................................................................................37 cm

Power Consumption ..................................................................................................... 36 W

Operating Voltage.................................................230 V (AC) ~50 Hz (by adapter 12 V DC)

TV System....................................................................................PAL I / NTSC PLAYBACK

Band ..........................................................................................................VHF 1 Band 2 - 4

VHF III Band 5 - 12

UHF Band 21 - 69

Band S S1-S41

Aerial Input.................................................................75 Ω (ohm) Standard Antenna Socket

Program Capacity................................................................................................100 + 3 AV

Picture Tube ..............................................................TFT LCD Panel 1024 x 720 resolution

Sound Output rms......................................................................................................2 x 2 W

Disposal of waste

RECYCLING: with a view to reducing disposal of waste

electrical and electronic equipment as much as possible,

do not throw out this end of life cycle appliance together

with other unsorted municipal waste, but make use of a

recycling centre.

Vers. 001 Technosonic LCD2018

Mains operation

MAINS SUPPLY 230- 240 V ~ 50 Hz

MAINS PLUG

The mains lead supplied with this equipment is fitted with a standard 13 amp plug (BS

1362) and is fitted with a 5 amp fuse. When changing or examining the fuse, the correct 5

amp fuse- ASTA or BSI approved (BS 1362) must be fitted and the fuse cover replaced.

The 13 amp plug is the most widely used type in the UK and should be suitable for most

users.

However some locations (mainly older buildings) may not be equipped with normal 13 amp

sockets. In such cases it is recommended that a suitable plug adaptor be purchased from

your dealer.

IMPORTANT:

This product is fitted with an approved non-rewire able 13 amp plug fitted with a 5 amp

fuse.

Should you decide to change the plug it should be cut from the power cord and disposed

of safely. Insertion into a mains socket would cause an electrical hazard.

However should you decide to change the plug. Please follow the instructions below:

IMPORTANT

The wires in the mains lead are coloured in accor-

dance with the following code:

Blue: Neutral

Brown: Live

As the wires in the mains lead of this apparatus may

not correspond with the coloured markings identifying

the terminals in your plug proceed as follows: The wire

that is coloured BLUE must be connected to the termi-

nal which is marked by the letter "N" or coloured black.

The wire that is coloured BROWN must be connected

to the terminal which is marked by the letter "L" or col-

oured red. A 5 amp fuse must be fitted either into the plug, adaptor or at the distribution

board.

DO NOT MAKE ANY CONNECTION TO THE LARGER PIN MARKED WITH THE LET-

TER "E" OR BY THE SYMBOL “W“ OR COLOURED GREEN OR GREEN AND YEL-

LOW.

The screw in this terminal must be fully tightened.

WARNING: The plug which you cut off the mains lead must be disposed of immediately

and safely, since a shock hazard will arise if the plug is inserted into a 13 A socket else-

where in the house. This appliance must be protected by a 5 A fuse, if a 13 A (BS 1 363)

plug is used. If any other type of plug is used, a 5 A fuse must be fitted in the plug or distri-

bution board. Only ASTA approved BS 1362 fuses should be used. This appliance must

not be connected to a multiple plug adaptor. The fuse carrier must be refitted in the event

of changing the fuse. Do not use the plug if the fuse carrier is lost. The fuse carrier must

be of the correct type and colour (as indicated by the plug base). Fuse carriers may be ob-

Technosonic LCD2018 Vers. 001

tained from your supplier or service centre. Should at any time the mains lead need repla-

cing, the replacement lead should only be fitted by a competent electrician.

What to do for safety of your TV

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER

(OR BACK). NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO

QUALIFIED PERSONNEL.

POWER SOURCE

You should only plug this TV into a 230-240 V AC 50 Hz mains supply.

MAINS AND OTHER LEADS

Position the mains supply lead and other leads so that they are not likely to be walked on,

pinched by things or placed on or against them. Pay particular attention to leads where

they enter a power socket and at the point where they come out of the TV.

MOISTURE AND WATER

Do not use the TV in a humid or damp area. The equipment must not be exposed to drip-

ping or splashing, as this may be extremely dangerous. Objects filled with liquids, such as

vases, must not be placed on this equipment.

NO NAKED FLAMES

Naked flame sources, such as lit candles, must not be placed near this equipment, or on

top of it.

CLEANING

Always unplug the TV before cleaning it. Do not use liquid or aerosol cleaners. Clean your

TV with a soft damp cloth.

BATTERY DISPOSAL

Your attention is drawn to the environmental aspects of infrared remote control battery

disposal.

Please dispose of depleted batteries responsibly and ensure you follow the battery manu-

facturers disposal instructions.

VENTILATION

The slots and openings on the TV are for ventilation.

Please ensure that there is enough space to allow for adequate ventilation around the TV

(at least 10 cm).

Do not block or cover these holes as overheating could occur.

Vers. 001 Technosonic LCD2018

REPLACEMENT PARTS

The person carrying out the job must use parts that are specified by the manufacturer or

have the same specifications as the original parts. The use of other parts may cause fire,

electric shock or other hazards.

SERVICING

Ensure the person carrying out repairs to your TV is qualified to do so. Please refer to

separate service information supplied with this product. Never remove the cover

yourself, there are dangerous voltages inside and you could receive an electric shock.

Safety information (continued)

LIGHTNING

In the event of a lightning storm, unplug your TV from the wall socket.

Always unplug the TV if going away on holiday.

GENERAL

• Do not connect or adjust cables while the TV is plugged into the mains supply.

• Do not leave your TV in a hot, cold or humid area.

• Batteries in remote handsets can leak. Please check the batteries regularly if they

have not been replaced recently.

• Never let anyone, especially children, push objects into holes and ventilation slots.

• Do not continue to use your unit if you have spilt liquids in it, if it is damaged in any

way or if it does not work normally. Immediately unplug the unit and get expert advice.

• This product is only designed for household or similar general use. Any other use

may invalidate the guarantee and may be dangerous.

• We are proud to offer this high quality product. To keep this equipment at this level of

quality, this equipment should only be serviced at your authorised service centre.

WHICH PART OF YOUR TV PERFORMS WHAT FUNCTION

Technosonic LCD2018 Vers. 001

Which of your TV performs what function

FRONT: BACK:

1 Standby button

7 Aerial in

2 Remote control sensor

8 "Scart in" (Using this entry, you can connect to

your TV such devices as computer, decoder and

VCR)

3 Speaker(s) 9 DC 12 V input

4 P+ / – Program up and down

buttons

10 AV out

5 + / – Volume up and

down buttons

11 SVHS in / L-R Audio in

6 AV input / Headphone input 12 Audio-PC input (Optional)

13 DVD Connect (Optional)

Vers. 001 Technosonic LCD2018

Remote control

1 Stand-by button

2 Direct program selection button

3 Swap button

4 Mute button

5 Menu selection button

6 TV button

7 Program button at TV position, page up (+) or down (-) button at Teletext position, up

(+) or down (-) movement buttons in the menus.

8 Volume up (+), clown (-) and in the menus adjustment buttons

9 Exit button

10 User normalization button

11 Status button (i)

12 * Audio selection button DUAL I, DUAL II, Stereo, Mono (DUAL I, II, ST/MONO)

(Not functional on mono models & mono broadcasting)

13 Automatic search button

14 AV button

15 (Blue key) Picture menu

16 * (Yellow key) Sound menu

17 (Green key) Timer menu

18 (Red key) Overview menu

19 Picture format selection (At some models)

Note: To use other key functions described in the menus, please refer to the remote con-

trol figure described in the TELETEXT section.

* Is not available for Mono models.

REMOTE CONTROL

TM36 03 TM37 02

Technosonic LCD2018 Vers. 001

Never drop your Remote Control.

Do not attempt to open your Remote Control.

Do not press any 2 buttons on Remote Control simultaneously

If you do not use your Remote Control for a long time, remove the

batteries.

Note: The remote controls the TV from up to 7 metres

and at a 30 degree angle.

BATTERY INSERTION (1.5V AAA x 2 pieces)

• Remove battery cover.

• Insert the batteries correctly.

• Close the cover.

CONNECTION

Vers. 001 Technosonic LCD2018

Aerial connection

Outdoor aerial connection

Optimum good picture and colour reception requires a good outdoor aerial.

Using a coaxial cable (75 Ω Fig. A-2) for a aerial, connect the plug (refer to Fig. A-1) into

the aerial input of the set.

Alternatively you may connect the aerial via a video recorder by using the video recorder

Rf Input and Rf Output connections as shown.

Back cover

Aerial

input

RF out

RF input

AERIAL Connection with video recorder

AERIAL socket

(Fig. A-1)

Coaxial cable (75

)

Fig. A-2

Scart socket

Technosonic LCD2018 Vers. 001

VCR, DVD, Satellite decoder and computer connections

EURO-SCART SOCKET

A Video Cassette Recorder, DVD Player, Games Console or Satellite Decoder may be

connected to the scart socket with an appropriate connecting cable. Select programme

mode AV to access the signal being received through the SCART Socket.

VCR OPERATION USING THE RF OUT

• To connect a VCR to your LCD TV using the

RF sockets, connect a coaxial cable from the

RF Out socket of the VCR to the aerial input

socket of your TV. Then connect the coaxial

cable from your TV aerial to the RF In socket

of the VCR.

• Select programme no. 0 on your LCD.

• Insert a video tape into the VCR and press the "play" key.

• Use the instructions under "Manual Programming" (found later in this Instruction Book)

to search and store the VCR's RF Output channel in Channel 0 on your LCD TV.

VCR AND DVD PLAYER OPERATION USING THE EURO-SCART SOCKET

• Connect the SCART socket on your VCR or

DVD Player to the SCART Socket on your

LCD TV.

• Select AV Channel on your LCD TV by press-

ing the AV selection key on your remote con-

trol handset.

• Press the PLAY key on your VCR or DVD

Player.

• The advantage of this connection is a superior quality of picture and sound during play

back.

PC CONNECTION (Optional)

• You may use your LCD TV as a PC monitor

by connecting the VGA cable of your PC into

the LCD TV'S PC socket.

Aerial

Coaxial cable

From “RF OUT”

To aerial socket

To “RF IN”

To “EURO SCART”

(VCR)

To “EURO

SCART”

(

)

LCD TV

Vers. 001 Technosonic LCD2018

Satellite receiver / cable TV receiver connections

a) With SCART Connector

• Connect the SCART socket on the receiver to the SCART

socket on your LCD TV using the appropriate SCART

connecting cable.

• Select AV Channel on your LCD TV by pressing the AV

selection key on your remote control handset. Your LCD

TV will now display the signal from your Satellite or Cable

Receiver.

b) Using AV Sockets

• If your Satellite or Cable Receiver is equipped with AV

Output (Phono) sockets then this provides an alternative

means of connecting your Receiver to your LCD TV.

• Using a 3-Way AV connecting lead, connect the Video,

Left Audio and Right Audio output sockets on your re-

ceiver to the corresponding input sockets on the side of

your LCD TV.

• Select AV Channel on your LCD TV as above.

c) Using the SVHS Socket

• If your receiver has a SVHS output socket, you can con-

nect this and your LCD TV'S SVHS input socket using

SVHS connecting cable. This method will carry the image

to your LCD TV.

• For audio connection use a 2-Way AV connecting lead to

connect your Receiver's left and right audio outputs to

your LCD TV'S left and right audio inputs on the underside

of the TV, next to the SVHS input.

• Select AV Channel on your LCD TV as above.

d) AV outputs:

• You can watch your TV's display and listen your TV's

sound in another device using AV outputs on the bottom of

your device.

• Also, you can listen to the sound from your TV via

an external speaker by connecting audio left and

audio right outputs to amplifier or audio set.

RECEIVER

Technosonic LCD2018 Vers. 001

TV Functions

1. TURNING ON

a. Turning TV ON

To turn your LCD TV on, connect the Mains Adaptor to the "DC In" socket. Connect the 3-

Pin UK Mains Plug to a suitable mains power supply and switch on. Your LCD TV will en-

ter Stand-By mode.

b. Stand-By Mode

When the TV is in stand-by mode, you can turn

it on by pressing one of the program selection

keys (0-9) or P+/P- on the Remote Control or

P+/P- keys on the TV.

2. TURNING OFF

a. Turning TV OFF

When you wish to turn off your television, unplug the adaptor.

b. Stand-By Mode

To turn TV off for a short time, press stand-by button on the Remote Control.

3. PROGRAM NUMBER SELECTION

• Press the P+/P- buttons on the TV control panel, to select the desired pro-

gram number.

• Select the program no.0-9 with the single number keys (0-9) on the Re-

mote Control, press and hold for a short time to skip the time for the sec-

ond digit.

• Select a program no.10-99, press number keys on the Remote Control without a long

interval.

Example: To move to program no.14, first press key 1. A message "1-" appears on the

upper left corner of the screen. If you hold this key pressed then it goes to program no.1.

While this message is on the screen (3 seconds), if the key 4 is pressed the TV will go to

programme 14. If the key 4 is not pressed within 3 seconds the TV goes to programme 1.

4. MUTE

To mute the sound immediately, press the mute button on the RC. If you press this button

again, you will hear the sound at the same volume as before.

5. STATUS KEY: ( i ) It indicates on the screen for 3 seconds, the channel system, pro-

gram no and name.

6. PP (Normalization): It brings the settings made on the menus related to picture and

sound in the form they have been last saved (user values).

* If you press the PP button sequentially two times, default factory (unchangeable) settings

will be displayed as selections "Cinema", "Music" and "Sport”.

Vers. 001 Technosonic LCD2018

7. S/M/D KEY: It is used to select stereo, mono or dual system.

8. AV: Press this button on the RC to select the AV mode. To return to the TV mode, press

the program number or TV button. Each time you press AV, it goes to AV (SCART), SVHS,

S AV, PC (At some models) and the last used TV channel respectively.

As long as there is a menu on the screen, you cannot go into the AV mode.

In the AV mode, you cannot access the INSTALLATION menu. You can only do adjust-

ments relating to other menus.

9. AUTOMATIC SHUT OFF

When there is no broadcasting signal, TV SET goes off automatically within five minutes.

NOTE: Automatic shut off function doesn't shut TV off in AV.

10. TV (EXIT) button:

To exit from menus.

11. Menu button:

This allows you to scroll between various on-screen menus.

Picture, Sound, Features, Installation and Input Source menus may be accessed sequen-

tially.

SET

Technosonic LCD2018 Vers. 001

Setup

Below, programming process is detailed for your device. More comprehensive information

on settings and menus can be found in the later pages:

You can make the adjustments using the P- (down), P+ (up) buttons.

You can make the menu option changes using V-, V+ buttons.

1) Make the connections as described in

previous pages and push display.

2) Press "green" button on the remote con-

troller and "features" menu will appear on

the screen. Check whether the language

is "ENGLISH", if not choose "English ".

3) Press "MENU" button and enter "IN-

STALLATION" menu.

4) Press "white" button and enter "auto-

programming" menu. In this menu:

A) Choose PI in "beginning" option.

B) Set "system" option to relevant se-

lection. This selection is "EUROPE"

for European countries except

France.

C) Change the "OFF" position of

"search" option with V+ button and

start searching.

5) Automatic programming lines up all

channels in their corresponding transmission frequency in numerical order. To alter

program locations and names, to clear and program manually, please consult the

menu description.

Vers. 001 Technosonic LCD2018

TV Functions (Menus)

MOVING THE SELECTION BAR IN THE MENUS: You can move the selection bar by

pressing the MENU key in the Menus. You press V+ button to INCREASE V- button to

DECREASE the parameters of actual selection in the menus.

By pressing "TV" button, "OSD" menu can be closed.

1. PICTURE SETTINGS MENU

The picture settings menu is accessed by

pressing either "blue" key or MENU key. In

the picture settings menu, many values rela-

ting to the picture can be changed. You can

adjust the brightness, contrast, colour,

sharpness and DCI according to your wish.

You can choose any of them using P+/P-

keys and increase or decrease using V+/V-

keys.

After the changes are done, move the selec-

tion bar to the Memory selection and press

the V+ button to save the new values in

memory. If you press MENU key, you will jump to the next menu. If you press TV key, you

will exit all the menus.

Colour Tone: NTSC PLAYBACK broadcast can activate this option. You can adjust the

colour tone in NTSC broadcasts.

DCI: For more contrast the option DCI must be open

2. SOUND SETTINGS MENU

(This menu is not available in some models)

The sound settings menu is accessed by

pressing either "yellow" key or MENU key.

After the changes are done, move the selec-

tion bar to the Memory selection and press

the V+ button to save the new values in

memory. In this menu, the following choices

are offered(see picture). You may choose

any of them using P+/P- keys and increase

or decrease the values using V+/V- keys.

Volume: The audio output volume of the TV

can be set.

* Balance: Indicates the volume balance be-

tween left and right channel outputs. Two vertical lines appear in the middle of the horizon-

tal balance when the outputs are balanced.

* Bass/Treble: The user may set the bass and treble level with this selection.

* Sound Select: You can select Mono/Stereo/Dual if the broadcast is available.

* Sound Effect: It changes the stereo effect level for a stereo or mono broadcast but this

function is only available in stereo models.

Store: You can save the adjustments.

(*)In mono TVs this feature does not work, and is not seen on menu.

Technosonic LCD2018 Vers. 001

3. FEATURES MENU

The features menu is accessed by pressing

either "green" button or MENU button until

"Features Menu" appears. This menu con-

tains "Language", "Sleep Timer" selections.

Language: The menu bar can be moved

P+/P- and you can select the "Language"

options by pressing V+/V- on the remote

control. The menu system is displayed in se-

lected language.

Sleep Timer: You can set the "Sleep Timer"

in the "Features Menu". The menu bar can

be moved on the "Sleep Timer" selection us-

ing P+/P- buttons and the sleep timer can be

set as: None - 15 min - 180 min by pressing

V+/V- buttons. The last 60 sec. is counted

down and displayed on the screen.

4. CHILD LOCK MENU:

(This menu is not available in some models)

This selection is set to "Off" as default value.

The "Child Lock" can be set using password.

The default password is 1,2,3,4 as default

value until changed. The valid password

must be four digit number between 0000 to

9999. (If you forget your password please

see notes in WARNING section).

Each digit entry is displayed as “*” symbol on

the screen. If you enter the password cor-

rectly, the "Child Lock" selection is displayed.

If you set this selection as "On" then your TV

will require the password when switched on.

The TV will work if the password is entered

correctly. If you want to specify new password, you can move the selection bar "New

Password" by pressing P+ and the V+ button.

The new password must be four digit number between 0000 to 9999. After your entry is

completed successfully then "Repeat" message is displayed and in this case you must en-

ter your new password once again. If you entered your password correctly then your new

password will be validated.

Note: When the child lock is activated, P+/P-, V+/V- buttons on the front panel can't

be used.

Vers. 001 Technosonic LCD2018

WARNING:

If you forget your password, you can enter 2,3,0,8,6 sequently and as quick as possible in

any time. In this case the "Child Lock" will be disabled and actual password is set to

1,2,3,4.

5. INSTALLATION MENU

On this menu, you can make automatic

channel search, find and save programs, de-

lete programs you no longer want, name

programs, change their order by moving or

hiding them. To enter this menu, press

MENU button or press the "red" button.

INSTALLATION

The following choices are offered in the In-

stallation menu: SELECT, CHANGE, DE-

LETE, MOVE, AUTOSTORE. These choices

are used for channel searching and arrang-

ing the program table. You can search for channels automatically and manually, delete

channels, and change the channel settings by pressing "change" (green button). The

menu bar can move through the program listing using P+/P- buttons. 10 programs are dis-

played on the screen at the same time. You can move on the listed programs and can

watch the program selected. V+/V- buttons scroll the display for the next (or previous) 10

programs. For example if you selected program 29 you can jump directly to program 39 by

pressing V+ button and you can jump to program 19 by pressing the V- button. You can

jump to next menu by pressing the MENU button or you can exit by EXIT button.

When the automatic search operation is finished, the caption "ready" will be displayed.

Press EXIT to exit from this menu.

5.1. AUTOMATIC PROGRAMMING (White button)

If you press the "White" button on remote

control unit in the "Installation" menu , you

will enter the "Auto. Program" menu. "Start

from". System" and "Search" selections are

available in the "Auto. Program" menu.

Start from : This selection allows to start the

automatic channel search procedure from

any programme between 0 e 99.

System: You can specify the TV system ac-

cording to the valid system in your country.

But this feature is selectable only for multi

system TVs, otherwise it is adjusted to valid

TV system by default.

Search: You can start searching with V-/V+ buttons.

Technosonic LCD2018 Vers. 001

5.2. DELETE (Red button)

This function allows the user to delete an undesired program in Program Table. You can

move selection bar moving between programmes using P+/P- buttons and press to delete

program. The deleted program disappears and other programmes are shifted up sequently.

Note: If you cancelled a program and wish to select it again, you can do so using

"Change" in INSTALLATION menu (by pressing green button on the remote control).

5.3. CHANGE (Green button)

You can enter "Tuning" menu by pressing

"green" button on remote control unit in "In-

stallation" menu. "Program", "Name", "Sys-

tem", "Search", "Fine Tune", "Store" selec-

tions are available in "Manual Tuning" menu.

Program: You can select the program num-

ber by pressing V+/V- buttons and move the

selection bar to the "Store" selection to store

the existing channel settings in memory.

System: It has the same function like "Sys-

tem" selection in the "Auto. Program" menu.

You can select the TV system according to

your regional broadcast system. This function is selectable only on the multi system TVs.,

otherwise it is predefined according to your TV system.

Search: You can start searching with V- (backwards), V+ (forward) buttons. Search will

end with the first found program. If it is not the program you want, you can start searching

again by pressing V+ or V- buttons. If you know the frequency number of the program you

are looking for, you can enter the number using numerical buttons.

Fine tune: This option allows the user to do fine tuning in the desired channel according to

his own wishes. This tuning is done using V+/V- buttons.

Store: Continue the searching process. You can store the program settings by activating

"Store". Move the selection bar to the "Store" using P+ button and press the V+ button to

store the channel settings.

Press EXIT to exit from this menu.

5.4. SELECT (Blue button)

Use the P+ / P- buttons to choose the name line and press the Blue button to select the

program. First character will begin to flash. You can begin to name the programs using P+

/ P- buttons. After each character you can go to the next one using V+ / V- buttons. You

can use Blue Button to save the name that you write.

5.5. MOVE (Yellow button)

You can move (swap) the location of desired program. Move the selection bar on program

line which you want to move and press the "Move" (yellow) button, then move the selec-

tion bar to the new location where you want to place the selected program and press the

"Move" (yellow) button to swap program location. The rest of the program table will be

sorted again according to your selections. You can jump the next menu using Menu button

or exit the menus using Exit button.

Page is loading ...

Teleco Monitor 15 Technosonic LCD2018 User manual

Brand: Teleco

Model: Monitor 15 Technosonic LCD2018

Category: LCD TVs

Type: User manual

Download PDF

report

Teleco Monitor 15 Technosonic LCD2018 User manual

Teleco Monitor 15 Technosonic LCD2018 User manual

Related papers

Other documents