Teleco Televisore Led TH2 19D User manual

  • Hello! I am an AI chatbot trained to assist you with the Teleco Televisore Led TH2 19D User manual. I’ve already reviewed the document and can help you find the information you need or explain it in simple terms. Just ask your questions, and providing more details will help me assist you more effectively!
INSTRUCTION MANUAL
TH2/19D
with built in DVB-T/S2/DVD
GB-2
1
LED TV with built in DVB-T/S2/DVD
SAFETY INFORMATION
IMPORTANT SAFETY INSTRUCTIONS - READ CAREFULLY BEFORE USE
Take note of the following safety information which appears on the back of this TV.
CAUTION! TO PREVENT ELECTRICAL SHOCK, DO NOT REMOVE ANY COVERS OR SCREWS.
NO USER SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
T
his symbol indicates that there are important operating and maintenance instructions in the literature
accompanying this unit.
This symbol indicates that dangerous voltage constituting a risk of electric shock is present inside this unit.
Keep these instructions
Do not use this TV near water.
Clean only with a slightly damp cloth.
Do not block any ventilation openings.
Install in accordance with the supplied Quick Start Guide and this User Guide.
Do not install or operate near any heat sources such as radiators, stoves, or other devices that produce heat.
Protect the power cord from being walked on or pinched, particularly at plugs, and the point where it exits
from the TV.
Do not allow the power cord to overhang the edge of a table.
Unplug this TV during lightning storms or when you do not intend to use it for a long period of time.
To avoid interference, switch this TV off while operating other radio devices in the immediate vicinity.
Refer all servicing to qualified service personnel. Servicing is required when the TV has been damaged
(e.g. the power cord or plug being damaged), liquid is spilt on it, objects have fallen onto it or the TV has
been exposed to rain or moisture, does not operate normally or has been dropped.
WARNING! TO REDUCE THE RISK OF FIRE OR ELECTRICAL SHOCK, DO NOT EXPOSE THIS TV
TO RAIN OR MOISTURE. THE TV MUST NOT BE EXPOSED TO DRIPPING OR SPLASHING AND
NO OBJECTS FILLED WITH LIQUIDS SHOULD BE PLACED ON THE TV.
No naked flame sources such as candles should be placed on the TV.
User Guide
CAUTION! CHANGES OR MODIFICATIONS NOT EXPRESSLY APPROVED BY THE
MANUFACTURER COULD VOID THE USER’S AUTHORITY TO OPERATE THIS
DEVICE.
CAUTION! USING CONTROLS, MAKING ADJUSTMENTS OR PERFORMING
PROCEDURES IN ANY WAY OTHER THAN AS SPECIFIED HEREIN MAY RESULT
IN HAZARDOUS EXPOSURE.
Important
This TV generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with
these instructions, may cause harmful interference to radio communication. However, this is no guarantee that
interference will not occur in a particular installation. If the TV does cause harmful interference to electrical
devices, which can be determined by turning the TV off and on, the user is encouraged to try to correct the
interference by one of the following measures:
Re-orient or relocate the receiving antenna.
Increase the gap separating the external device and the TV.
Connect the external device to an outlet on a circuit different from that to which the TV is
connected.
Consult the dealer or an experienced radio/TV technician for help.
Specifications Troubleshooting Using DVD Using TV Installing Introducing Safety Warnings
Features Features LED TV LED TV
2
Contents
Safety Warnings .....................................................................................................1
Contents ................................................................................................................. 2
Chapter 1 Introducing the LED TV
Package Contents...................................................................................................... 3
LED TV Controls......................................................................................................... 4
LED TV Connections.................................................................................................. 5
Remote Control.......................................................................................................… 6
Chapter 2 Installing the LED TV
Wall Mounting............................................................................................................. 7
Preparing your LED TV for use ….............................................................................. 8
Connecting a TV Cable or an Antenna....................................................................... 9
Connecting External Devices.................................................................................... 10
Using the CI Plus Slot................................................................................................ 12
Installation Guide Setup............................................................................................. 13
Chapter 3 Using the TV Features
Basic Operation......................................................................................................... 14
Customising the Picture Settings............................................................................... 17
Customising the Sound Settings................................................................................ 18
Customising the Channel Settings............................................................................. 19
Customising the Feature Settings.............................................................................. 20
Customising the Setup Settings................................................................................. 22
S2 Basic Functions ................................................................................................... 24
Customising S2 Edit Channel Settings...................................................................... 25
Customising S2 Installation Settings....................................................... 26
Customising S2 System Setup Settings.................................................................... 27
Customising S2 Tools, game and REC settings......................................................... 28
Chapter 4 Using the DVD Features
Using the DVD features............................................................................................. 29
Customising DVD Operation...................................................................................... 31
Customising DVD Function General setup................................................................ 36
Troubleshooting .................................................................................................. 39
Specifications ...........................................................................…………............. 40
CE (EU) Certification ........................................................................................... 41
3
Chapter 1 Introducing the LED TV
INTRODUCTION
Thank you for purchasing this LED TV with DVD Player which has been designed and
manufactured to give you many years of trouble-free service.
You may already be familiar with using a similar product but please take the time to read these
instructions carefully: they have been written to ensure you get the very best from your
purchase.
Throughout the remainder of this user guide the LED TV with DVD Player will be referred to as
the ‘TV’.
HDMI
HDMI (High Definition Multimedia Interface) is the next generation of digital interface. Unlike
conventional connections, it transmits uncompressed digital and audio signals using a single
cable. This TV supports high-definition video input via the HDMI socket on the back of the TV.
Safety First!
To ensure both your own safety and that of others, please read the Safety Information
BEFORE you operate this product.
Keep this information in a safe place for future reference.
Package Contents
Make sure the packaging contains all the following items.
IN THE BOX
You will find:
LED TV without TV Base
TV Base
User Guide
Remote Control with batteries
Car Power Supply Lead
NOTE: These items are all you need to set up and operate the LED TV in its basic
configuration. If any of the items listed are damaged or missing, please contact us.
Specifications Troubleshooting Using DVD Using TV Installing Introducing Safety Warnings
Features Features LED TV LED TV
4
LED TV controls
Front/Top/Right View and Controls
LED
The LED light indicates when the LED TV is on.
IR
Infrared Receiver
SYMBOL DESCRIPTION
STANDBY BUTTON, Turns the LED TV on / sets it to standby mode.
INPUT BUTTON, Used to select from among different input signal
sources.
MENU BUTTON, Press once to display the menu, press again to
exit the menu.
CH-/CH+ BUTTON, Used to scan up or down through the channels.
In menu mode used to select the desired sub-menu item.
VOL-/VOL+ BUTTON, Adjusts volume. Also used to select main
menu items and adjust various item settings in menu mode.
PLAY/PAUSE BUTTON, Plays or pauses the disc in DVD mode.
EJECT BUTTON, Ejects / loads the disc in DVD mode.
Specifications Troubleshooting Using DVD Using TV Installing Introducing Safety Warnings
Features Features LED TV LED TV
5
LED TV connections
Left/Right Side Bottom View and sockets
No. DESCRIPTION
1 12 V DC in Connect the DC power lead to this socket.
2 USB in Connects to USB device.
3 HDMI in Connects to devices with HDMI interface
4 PC in Connects to a PC or other devices with a VGA
interface.
5 PC AUDIO in Connects to a PC audio socket or other devices with
a VGA interface.
6 SCART in Connects to external devices with SCART socket.
This SCART input allows video/audio in + RGB +
video/audio out from an external device to be
shown on your TV.
7 Common Interface Allows a CAM (Conditional Access Module) smart
Plus (CI+) card to be inserted to access the functions in the
card.
8 Coaxial out Digital audio out (coaxial output only for TV)
9 mini AV in Connects to camcorder, VCR, DVD Player, Digital
Set-Top-Box or other A/V equipment with composite
and audio sockets/jacks.
10 mini YPBPR in Connects to the DVD Player, Digital Set-Top-Box or
other A/V equipment with component (YPBPR) video
sockets/jacks
11 RF in Connects to your RF antenna or LNB cable.
12 EARPHONES out Connects to headphones.
*you may need to readjust the volume when using
headphones.
13 IR (infrared) extender Connects to IR signal input or output device.
Specifications Troubleshooting Using DVD Using TV Installing Introducing Safety Warnings
Features Features LED TV LED TV
ON/OFF switch
6
Remote Control
• Turns the TV on / sets it to standby
mode.
• Switches between different preset picture
modes.
• Switches between different preset sound
modes.
• Use to select and switch to a channel by
using 0-9 buttons or edit the item name in
the DVB-S2 menu.
• Press to pause, stop or delay DTV
program playback.
• Press to return to previously viewed
channel
NAVIGATION buttons
UP/DOWN/LEFT/RIGHT
Allows you to move, select and set up
the OSD options.
Allows you to confirm your selection in
the OSD options.
• Goes back to the Disc menu.
• Displays the electronic program guide in
DTV mode.
• Goes to the DVD title menu.
• Scrolls through the customised Favourite
Channels list
• Displays program information.
• Down-changes FAVOURITE channels.
• Goes to desired time and program.
• Searches for desired channel by channel
name. Up-changes FAVOURITE channels.
• Switches between TV and Radio in DTV
mode. Program playback in DVD mode.
• Plays program frame by frame in DVD
mode.
• Repeats playback during
playing of multimedia files.
• Repeats playback of segment
A-B during playing of multimedia files.
Coloured Buttons
(RED/GREEN/YELLOW/CYAN)
Accesses Teletext items or corresponding
pages. The coloured buttons are also use
to access interactive modes when the TV is
in DTV or menu mode.
• Selects different DVD
angle. Press to display the channel list.
• Displays your favourite
sub-title in DTV or DVD mode.
• Selects the screen aspect mode.
• Recording Menu.
Auto-adjusts the picture on the TV in PC
mode. Loads/ejects disc in DVD mode
• Mutes / restores TV sound.
• Displays current TV status, TV Channel,
input source, etc.
Switches between different audio languages
in TV/DTV/DVD mode (only applicable when
the TV program has this feature).
• Displays the TV Menu.
• Displays the DVB-S2 or DVD SETUP
Menu or exits the OSD menu.
• Selects from among different input
sources.
• Sets the TV sleep time.
• Changes the channels up and down.
• Increases/decreases volume.
• Turns Teletext function on/off.
• Toggles between different slow motion
speeds in sequence or plays program
frame by frame.
• Freezes a multi-page passage on
screen in Teletext mode.
• Plays or pauses program playing
.
• Goes to next page in Teletext mode.
• Stops or resumes program playing.
Activates zoom function during media
playing.
• Goes to previous page in Teletext mode.
• Displays the main index in Teletext
mode. Goes back to previous program.
• Freezes multi-page scrolling on screen
in Teletext mode. Goes to next program.
• Shows hidden info such as quiz answers
in Teletext mode.
• Plays a program in fast rewind mode.
• Displays the sub-page on the Teletext
screen.
• Plays a program in fast forward mode.
Specifications Troubleshooting Using DVD Using TV Installing Introducing Safety Warnings
Features Features LED TV LED TV
7
Chapter 2 Installing the LED TV
Wall Mounting
How to remove the TV Stand
I
f you would prefer to mount your new TV on a wall instead of on the base, please remove the TV stand and
follow the instructions included in the wall mounting kit (not included).
R
ead all the instructions before proceeding with stand removal.
a. Open the box, and make sure all the necessary parts are in the box. The TV is assembled with the stand.
LED TV without TV Stand arm
Four mounting holes
Size: M4 screws
How to wall mount the TV
Use four screws to mount the TV on the bracket.
This unit is VESA-compliant and designed to be wall-
mounted with a VESA-compliant 100x100mm mounting
kit. Mount this unit according to the instructions on the
wall bracket (not supplied).
b. Lay a soft cloth out on an even stable surface. Place the LED TV unit screen-down on the cloth. Unscrew one
screw anti-clockwise as shown in 1 and unscrew both screws in the same direction as shown in 2.
How to install the TV Base
a. If you want to attach the TV base, fit it onto the bottom of the stand arm as shown in 3, then rotate the base
anti-clockwise to its normal position.
b. Screw both screws back clockwise as shown in 4.
2 screws
ST4x6
Specifications Troubleshooting Using DVD Using TV Installing Introducing Safety Warnings
Features Features LED TV LED TV
8
Preparing your LED TV for use
How to set up the TV
Use an antenna cable to connect the RF signal to the LED TV RF IN terminal (refer to page 9).
Connect one end of the DC source unit to the back of the TV, and the other end of the DC source unit
to the power source.
Insert two AAA size batteries (supplied) in the remote control.
Step 1 Push and slide the back cover to open the
battery compartment of the remote control.
Step 2 Insert batteries. Make sure the (+) and (-) poles
of the batteries match the (+) and (-) terminals in the battery
compartment. Snap the cover back in place.
Do not clean the remote control with caustic cleaning agents (such as porcelain, stainless
steel, toilet, or oven cleaners etc.) as doing so may damage it.
Using the Remote Control properly
Never mix used and new batteries in the device.
Replace all the batteries in the device at the same time.
Remove the batteries if the remote control is not to be used for an extended time period.
To avoid faults read the following instructions and handle the remote control properly.
Do not drop the remote control or knock/slam it against a surface.
Do not get water or any other liquid on the remote control.
Do not place the remote control on a wet surface.
Do not place the remote control in direct sunlight or near sources of heat.
NOTE: Remove the batteries from the remote control handset when it is not to be used for a long period to
prevent corrosion, battery leakage or physical injury and/or property damage, including fire.
Connect another external A/V equipment (refer to page 10).
Remote control range
Your LED TV can be operated from up to 5m away when the
remote control is pointed directly at the receiver.
Specifications Troubleshooting Using DVD Using TV Installing Introducing Safety Warnings
Features Features LED TV LED TV
9
LED TV
Connecting a TV Cable, Antenna or Dish
For information on connection procedures refer to the owner’s manuals of any external devices.
When connecting external devices do not connect any AC power leads to mains power sockets until all other
c
onnections are completed.
C
onnecting a TV Cable or an Antenna
A
ntenna Connection
The antenna requirement for good colour Digital TV reception is more exacting than it is for analogue TV
reception. A good quality outdoor antenna is therefore strongly recommended.
Connecting to the TV (CATV) cable
A 75-ohm coaxial cable connector is built into the set for easy hook-up.
When connecting the 75-ohm coaxial cable to the set, connect the 75-ohm cable to the
RF IN terminal.
For best results use a high gain TV aerial, preferably roof or loft mounted.
To improve picture quality in a poor signal area, purchase and install a signal amplifier.
If the antenna needs to be split between two TVs, use a 2-Way Signal Splitter (not supplied).
Satellite Dish Connection
You can connect a fixed satellite dish or one on a motorized positioner or connect multiple fixed dishes using a
DiSEqC 1.0 switch.
RF switch
(not included)
2-way signal
splitter
(not included)
Cable
TV line
Cable TV converter /
decoder (not included)
DisEqC Switch
IN
OUT
IN
IN
OUT
Specifications Troubleshooting Using DVD Using TV Installing Introducing Safety Warnings
Features Features LED TV LED TV
10
Connecting External Devices
B
ottom Side View of TV
R
ight Side View of TV
Mass Storage Device
VGA AUDIO cable
VGA Cable
HDMI Cable
A/V EQUIPMENT
Left Side View of TV
SCART Cable
GAMES CONSOLE
VIDEO CAMERA
HEADPHONES
VCR
mini AV Cable DVD PLAYER
mini component
Cable
TV CABLE BOX
Satellite antenna cable
SATELLITE RECEIVER
Mass Storage Device
AV RECEIVER
MIR DEVICE
Specifications Troubleshooting Using DVD Using TV Installing Introducing Safety Warnings
Features Features LED TV LED TV
11
Connecting External Devices
Connecting A/V Equipment with an HDMI Connector
This TV accepts HDMI (High-Definition Multimedia Interface).
This TV SET supports the HDCP (High-Bandwidth Digital Content Protection) Protocol for the TV set modes
(
480p, 576p, 720p, 1080i etc.).
When you connect to the output of an HD-ready player (DVD Player, Set-Top-Box or PC) switch to the HDMI
function: the TV will automatically detect the resolution used by the HDMI source.
To get the best picture quality, adjust the output resolution of the DVD Player or Set-Top-Box to 720p.
U
se an HDMI cable to connect the A/V equipment HDMI output socket to the LED TV HDMI input socket.
The HDMI connector provides both video and audio signals. Therefore, it is not
necessary to connect the audio cables.
Connecting a PC
Use a VGA cable to connect the VGA output socket on the PC to the PC IN socket on the LED TV. Use an audio
cable to connect the audio output sockets on the PC to the PC AUDIO IN sockets on the LED TV.
The best resolution for this TV is as follows:
1360 pixels (horizontal) x 768 pixels (vertical) - TH2/19D
If the PC is set to auto-idle after a set time, then the TV may also enter standby mode due to
no input signal being detected.
To avoid this happening you will need to configure the PC.
Proceed as follows.
1. Click Start on the computer desktop screen.
2. Select Control Panel.
3. Click twice on Power Options and select Never from the Turn off Monitor drop-down box.
4. Then, again on the Control Panel, click twice on Display, then select the Screen Saver tab
and select None from the screen saver drop-down box.
This will prevent the TV from going to Standby mode.
Connecting an A/V Equipment with a miniComponent(YPBPR)/miniComposite Connector
Use a minicomponent/minicomposite cable to connect the external component/video output sockets on the A/V
equipment to the miniYPBPR IN/miniAV IN sockets on the LED TV. Use a miniAV cable to connect the external
audio sockets on the A/V equipment to the miniAV sockets on the LED TV.
The video component sockets on your A/V equipment are sometimes labelled YPbPr or YCbCr.
For an explanation of video component, see your A/V equipment user’s guide.
Not all A/V devices can be connected to a TV via the Composite connector. Please check your A/V
equipment user’s guide for compatibility.
Connecting an A/V Equipment with SCART Connector
Use a Scart cable to connect the SCART socket on the external A/V equipment to the SCART IN socket on the
LED TV.
Specifications Troubleshooting Using DVD Using TV Installing Introducing Safety Warnings
Features Features LED TV LED TV
12
How to connect a CI (Common Interface) plus card
C
ARD FACE FRONT
NOTE: The Conditional Access Module (CAM)
does not come with the TV set.
It can only be obtained when you subscribe to service
providers like PayTV or other service providers
When you use the CI plus slot for the first time there
may be a dummy card already inside it; if so, remove
it and then insert the CAM.
CI (Common Interface) slot
Allows the Conditional Access Module
(CAM) smart card to be inserted to
access the encrypted content.
Using the CI Plus Slot
To view DVB-T or DVB-S2 encrypted (pay to view ) services in
digital TV mode.
• INSERTING THE CAM CARD
Insert the CAM card into the DVB-T or DVB-S2 slot in the direction
indicated by the arrow until it fits in place; the card face (label) must
face forwards.
COMMON INTERFACE
CAM label
Make sure the CAM label faces front.
CAM (Conditional Access
Module) Smart card
• REMOVING THE CAM CARD
To remove the CAM card just pull it out of the slot.
This function enables you to watch selected encrypted (pay) services of certain channels. Please switch
off your TV, read the instructions provided with the CAM and ensure it is inserted correctly before
switching the TV on again.
Press the INPUT button on the remote control to display the Input source menu, and use the
UP/DOWN buttons to select DVB-T or DVB-S2.
Specifications Troubleshooting Using DVD Using TV Installing Introducing Safety Warnings
Features Features LED TV LED TV
13
Installation Guide Setup
W
hen you switch on the TV for first time, the DVB-T Auto Installation menu appears on the screen.
Press to select Home Mode and press GREEN to go to the Next Page to select the Country,
Language and Auto Power Off settings; lastly, select the Auto Search type to start the tuning program.
You can press EXIT to quit the screen or
press RED to go to the Previous Page to
re-select the previous setting.
DVB-T (Digital Video Broadcasting - Terrestrial)
Before you begin using your DVB-T TV please note the following:
1. Your existing aerial may not be suitable for receiving Digital signals.
2. Your existing aerial may not be pointing in the correct direction.
3. Your house may be located in an area where Digital TV reception is poor.
The above factors may prevent you from receiving some or all of the Freeview Channels.
In the event of difficulty please contact a qualified aerial installation engineer for assistance.
Do not adjust your TV set as it is not faulty.
Never agree to have work done by anyone who calls without an appointment and does not show ID and/or credentials.
Re-Tune
If you experience a loss of one or more channels please re-scan. Service providers sometimes alter program
locations without prior notice. Please retune the TV before calling for technical assistance.
{ Press the INPUT button on the remote control to display the source list. Use the UP/DOWN buttons to select
other sources you wish to watch and press the OK button.
If the LED TV is not to be used for some length of time always disconnect it from the power
source. The STANDBY button on the top panel is only used to switch the LED TV to standby,
it does not disconnect the device from the power supply.
To disconnect from the power supply remove the DC plug from the bottom i/o board of the TV set.
Specifications Troubleshooting Using DVD Using TV Installing Introducing Safety Warnings
Features Features LED TV LED TV
14
Chapter 3 Using the TV Features
Basic operation
Selecting the input source
Selecting an input signal source
You can select an input signal source by pressing the INPUT button on the TV control panel: press it
and the onscreen display menu shows the diagram illustrated below. Then press the CH+/CH- buttons
o
n the control panel or the UP/DOWN buttons on your remote control to choose an input signal source.
If your audio and video devices are connected to your TV you can choose from the following input signal
sources:
Adjusting volume
When you press VOL+/VOL- to increase/decrease volume the diagram below appears on your
screen for 5 seconds.
The MUTE symbol appears in a corner of the screen when you press the MUTE button; press the
MUTE button again and the symbol disappears.
To restore sound press either the MUTE button or the VOL+ button. The indicator below shows the
sound level.
Channel/favourites list:
Lets you customise the Channel/Favourite List under ATV/DTV Operation. Press the LIST/FAV button to
display the Channel List/Favourite List; use the UP/DOWN button to highlight and select the channel
you wish to watch. Press OK button to confirm.
Before any customisation can be effected, the Favourite List must be preset in the favourite
management menu.
Specifications Troubleshooting Using DVD Using TV Installing Introducing Safety Warnings
Features Features LED TV LED TV
15
Customising TV Operation
Basic TV operation
Program Guide MENU (only available in DVB-T):
A
llows you to customise the Program Guide menu.
Press the EPG button to display the Electronic Program Guide information menu.
U
se the NAVIGATION buttons to highlight an individual EPG item.
Press the UP/DOWN buttons to select an item.
Press the RED button to activate the Weekly or Daily view.
Press the YELLOW or BLUE button to view Previous Day or Next Day.
Reminder
Press GREEN to start creating a viewing or recording plan; press once only for viewing and twice for
recording. If the standby mode has timed out, 2 minutes are needed before reactivation and
background recording will start without powering the panel. To watch the program it is necessary to
press STANDBY.
Info (Display)
Press INFO to view in extended mode.
*Note: Automatic record when EPG reminder timer is active when a USB device is present.
*Programs may change without notice. Always check schedules on the day of broadcast.
TimeShift (available in DVB-T mode):
Allows a program to be recorded and the program being recorded to be played at the same time. This
function is only available when you connect a USB device and set Timeshift Buffer on the PVR/Timeshift
menu. Press TIMESHIFT to start timeshift-recording a program when continuous viewing is interrupted and
you wish to resume viewing later. When playback resumes you can use PAUSE/PLAY/FF/FB/PREV/NEXT
normally, use a pop-up virtual keypad bar or press STOP to return to normal mode. Alternatively, you can
press the PAUSE button to start Timeshift when no menu is highlighted and press it again to resume the
process. If, during the recording process, the signal fades/disappears, the recording process will pause until
the
signal re-stabilises.
Specifications Troubleshooting Using DVD Using TV Installing Introducing Safety Warnings
Features Features LED TV LED TV
16
Basic TV operation
S
electing the Media Source
If a USB device is connected you can select the Media source from the input menu.
Photo/Music/Movie/e-Book playback
Press the LEFT/RIGHT button to toggle among the Photo, Music, Movie, and e-Book browsers. Select the
U
SB disk and partition. Four different patterns are available to handle these four types of media content. The
system automatically classifies files, showing only the corresponding supported files.
Note: the USB interface supports *.mpg/*.dat/*.vob/*.avi/*.mp3/*.jpg/*.bmp/*.png/*.txt file types etc.
*Note: large image files may be slow to appear on the screen.
File Browser screen
Allows user to delete or add/del all files to/from a playlist via the RED or GREEN button.
Allows user to show selected file information on the right of the screen.
Allows user to press NAVIGATION and OK buttons to tick folders and files to be played back on the list.
Allows user to press the PLAY button to play back the file on the list.
Allows the user to press the EXIT button and then LEFT/RIGHT to switch between thumbnails and list mode on the Photo explorer
screen.
File Playback screen
Allows user to display a virtual keypad for various tasks that are unavailable on the remote control.
Press ENTER to pop it up and EXIT to hide it; alternatively, it will be displayed in the bottom right part of the screen in music playing
screen or none of the above when reading an e-Book.
Press the RED button to add or delete a bookmark, press the GREEN button to go to a desired page, press the YELLOW button to
pop up a Bookmark list, press BLUE to pop up Playlists and press FB or FF to page up or page down in e-Book mode.
Same as PLAY/PAUSE button on the remote control: press to resume playback or pause a multimedia file.
Same as the STOP button on the remote control: stops playback and returns you to the previous screen.
Toggles the repetition function: Repeat 1, Repeat All, Repeat Dir and Random modes.
Sets A-B repeat to play between A and B repeatedly: press once to set point A, press again to set point B, press a third time to
cancel.
Playlist: pops up the playback list in Photo/Music mode.
Info.: Same as the INFO button on the remote control: pops up a file information window in Photo/Movie/e-Book mode.
Rotate: rotates the picture in Photo mode.
Zoom in or zoom out in Photo/MOVIE mode.
Slow: playback at 1/2, 1/4, 1/8, 1/16 speed in Movie mode.
Step: frame by frame playback in Movie mode.
Press to pop up a setup menu to adjust telecast function: this includes Repeat Mode, Background Music, Music Source, Slide Time,
Effect in Photo mode and Program, Subtitle, Audio, Repeat Mode in Movie mode.
Goto Time: enter the search date/time in Music/Movie mode.
Same as the FB/FF button on the remote control: play fast backward or forward at x2/x4/x8/x16 speed.
Same as the PREV/NEXT button on the remote control: play previous or next multimedia file directly.
Same as the BLUE button on the remote control. Used to close panel in Music mode only; it can be opened by pressing any button
on the remote control.
*Note: These functions require a USB mass storage device to be connected.
Customising TV operation
Specifications Troubleshooting Using DVD Using TV Installing Introducing Safety Warnings
Features Features LED TV LED TV
17
Customising TV operation
Menu Operation
All functions can be operated via the remote control or operated partially via the keyboard.
T
he main menu is controlled via the MENU, OK and EXIT buttons.
Use the MENU button to open the menu or go to a higher level. There are five main menu pages on the DVB-T
system: Picture, Sound, Channel, Feature, Setup.
Press the Navigation button to select a function or adjust settings, Press OK to confirm a selection, Press the
E
XIT button to go up a level.
Customising the Picture Settings
Picture MENU:
Allows you to make adjustments to your picture settings.
Picture Mode
Toggles between display types: Standard/Mild/User*/Dynamic.
*User: allows you to save your preferred settings.
Brightness
Controls overall brightness level of the picture: the higher the level the brighter the picture.
Contrast
Controls difference in colour and light between different parts of an image. The higher the contrast the more marked the user-
perceived difference.
Sharpness
Controls picture sharpness. Higher settings sharpen the image more.
Colour
Controls colour intensity. The higher the setting the more vivid the colour.
Tint (for NTSC system only)
Controls the difference between green and red regions of the picture.
Colour Temperature
Adjusts colour components independently to achieve a warm or cool effect: Standard/Cool/Warm
Aspect Ratio
Toggles between aspect types:
Auto/4:3/16:9/Full/Zoom1/Zoom2/Panorama etc.
NOTE: The available aspect mode may vary according to the input source signal.
*Not available in PC or USB mode.
Noise Reduction
Reduces noise and improves the appearance of the picture. Noise reduction gives good results but creates blur on pictures when
switching from Low to High. The available levels are Off/Low/Middle/High. *Not available in PC mode.
Specifications Troubleshooting Using DVD Using TV Installing Introducing Safety Warnings
Features Features LED TV LED TV
18
Customising TV Operation
Customising the Sound Settings
Sound MENU:
Allows you to customise the sound options and effects.
The Sound Setup menu includes the following options:
Sound Mode
Allows selection of the following sound enhancement options: *User/Standard/Movie/Music/Speech
*User: allows your preferred Bass/Treble settings to be adjusted and saved.
Bass
Controls the relative intensity of lower-pitched sound in User mode.
Treble
Controls the relative intensity of higher-pitched sound in User mode.
Balance
Adjusts relative volume between left/right soundtracks. If balance is negative, the sound on the left track is
louder. If balance is positive, the sound on the right track is louder.
Surround
Allows you to generate virtual surround sound.
AVL
Auto-adjusts sound volume.
SPDIF Mode
Allows user to modify digital sound output from the COAX port. The available options are: Off/PCM/Auto.
Specifications Troubleshooting Using DVD Using TV Installing Introducing Safety Warnings
Features Features LED TV LED TV
/