Page is loading ...
FIAT DUCATO installation
Installations instruction
Navigation and multimedia Kit
KIT CONTENTS
• Fiat Ducato dedicated wiring
• Finishing frame
• 2-way M3 series coaxial speakers
• Speaker adapter
ENG
1
Parts to remove (1/3)
Grille
Dash slots
2
Parts to remove (2/3)
LH pillar cover
Instrumentation cover
ENG
ENG
3
Parts to remove (3/3)
Instrumentation panel
LH cable cover
4
ENG
Speaker Installation (1/2)
Speaker pre-setting
Speaker fixing support
Support
location
view
¥ Install the support to engage it with the
vehicle s speaker pre-setting and secure it
with the 3 supplied screws.
ENG
5
Speaker Installation (2/2)
Speaker connection adapter
• Fasten the speaker to the support
with the 4 supplied screws as shown
in the figure.
• Close the compartment back with its
original grille.
Connect the adapter to the vehicle
original wiring
Speaker connection
6
ENG
Preparation for radio installation (1/3)
¥ Saw off the highlighted parts to allow for double DIN metal casing insertion.
NOTE: Saw off with a hacksaw, making sure none of the cables provided
for radio connection are cut or damaged.
Remove the dash slots
ENG
7
Preparation for radio installation (2/3)
• Remove the 4 highlighted screws to allow for metal bracket insertion.
Screws to remove
Screws to remove
8
ENG
Preparation for radio installation(3/3)
• Insert the brackets as shown, following
the instructions provided on the left-
hand and right-hand brackets, then
fasten them with the screws that had
been previously removed.
L.-H. bracket
R.-H. bracket
ENG
9
GPS Antenna Installation (1/4)
• To ensure ideal operation of the navigation system, the GPS antenna installation
position should be carefully selected.
• The antenna direction is also essentially important for good reception.
• The recommended procedure is described here below.
• Loosen the glove box and install the GPS antenna
• The GPS antenna location is shown in the pictures here below
GPS antenna ideal position
10
ENG
GPS Antenna Installation (2/4)
• Loosen the two highlighted screws with a Torx screwdriver and lift the plastic support
to be able to introduce the GPS antenna.
• Introduce the antenna below the grille checking that it is positioned like in the figure.
Correct GPS antenna direction
Correct GPS antenna positioning
ENG
11
GPS Antenna Installation (3/4)
• Introduce the GPS antenna through the double DIN compartment to position it below
the glove box grille.
• By tightening the glove box compartment screws, the antenna will be pressure-
fastened.
• Ensure that the antenna direction is like in the photo.
Grille of the glove box compartment after antenna introduction
12
ENG
GPS Antenna Installation (4/4)
OK - CORRECT ANTENNA DIRECTION
In the correct direction of installation, the antenna will have
its BLACK surface facing up
NO! - INCORRECT ANTENNA DIRECTION
Caution: if the GPS antenna is installed facing in the wrong direction,
the reception quality will be affected and may cause incorrect
navigation system operation.
ENG
13
Microphone cable installation (1/2)
• Loosen the door pocket compartment to allow the Microphone cable to be led through;
fasten it by gluing it on its support facing the driver.
Hands-free microphone ideal position
14
ENG
Microphone cable installation (2/2)
•Route through the microphone cable as shown in the photos
ENG
15
iPod wiring
• Position the iPod cable in the glove box.
• Use the hole in the top part of the box to let the cable out.
iPod connector location
16
ENG
Parking brake enabling
• Route the Parking brake enabling cable as shown in the figure, and fasten it with
straps to the vehicle’s original cable harness
ENG
17
1. ISO speakers
2. ISO input
3. Parking brake
GPS antenna
1
2
3
4
5
6
7
8
1
2
3
4
5
6
7
8
Verde / Bianco (Freno di stazionamento)
Rosa (Consenso retrocamera)
Arancio/Bianco (Tasti A)
Bianco / Marrone (Tasti B)
Marrone / Nero (Massa)
Giallo
Rosso
Bianco
Rosso
Bianco
Rosso
Bianco
Giallo
Blu
1
2
3
Control for steering wheel controls
Radio antenna
18
ENG
Parking brake connectors’ detailed view (1/2)
To activate the PARKING function, the following operations should be carried out on
the vehicle wiring:
• Remove the tape wrapping the bundle of cables, making sure the cables are not
damaged in the process.
• Isolate the ORANGE/White cable coming from the handbrake button.
• Cut the ORANGE/White cable and connect the supplied wiring as shown here below
(follow the letters A and B for correct wire positioning).
ORANGE/White
ORANGE/White
GREEN
/