2. Computers & electronics
  3. Telecom & navigation
  4. Mobile phones
  5. Car kits
  6. AGI
  7. STX2 Double-Groove Pulley Electric Clutch

AGI STX2 Double-Groove Pulley Electric Clutch, XTA Double-Groove Pulley Electric Clutch Owner's manual

  • I have reviewed the provided installation instructions for the AGI Electric Clutch Kit A224/A225. This document details the process of installing the electric clutch, including mechanical assembly and electrical wiring. It also covers the proper placement of rubber straps to secure the clutch. I'm ready to assist you with any questions you may have regarding the installation process or the functionality of this product.
  • What should be applied to the engine shaft before sliding on the electric clutch?
    What size bolts can be used to secure the electric clutch to the engine shaft?
    How does the rubber strap prevent clutch rotation?
    What gauge crimp connectors should be used for electrical connections?
31043 R4
Revised: DECEMBER 2021 1
A224/A225
Electric Clutch Kit
Double-Groove Pulley
Installation Instructions
Applicable Models:
STX2 & XTA Series
Install the Electric Clutch
Note
Apply anti-seize to the engine shaft where the electric clutch will slide on.
1. Slide the square shaft key (3) and electric clutch (2) onto the engine shaft (1).
2. Secure the electric clutch to the engine shaft using a 3/8" x 3" bolt (4) or 7/16" x 3" bolt (4) (engine-model
dependent) and lock washer (5).
Note
When properly adjusted the electric clutch should be tight and unable to slide on the shaft.
3. Place the motor so that the gap between the face of the electric clutch and the inside face of the guard
attach bracket is 2-5/16".
Figure 1. Installing the Electric Clutch
2
13
54
2-5/16"
4. Connect all belts.
2 31043 R4
5. Remove the lock nut (7) to slide the rubber strap (8) over 3/8" x 1" bolt (6), re-attach the lock nut (7) to hold
the strap in place.
6. Position the rubber strap (8) using a 5/16" x 1" bolt (9) and two washers (10) on either side so that it fits
into the clutch case slot to prevent clutch from rotating, and secure it with a 5/16" lock nut (11).
Figure 2. Installing the Rubber Strap
Wire the Electric Clutch
1. Plug the clutch wiring harness into the clutch, and position the other end of the harness in a way that leaves
it accessible for external wiring.
2. Complete the remaining electrical connections, using 14 gauge crimp connectors (splice, spade, and ring
terminal) as needed:
• connect the white switch cable wire to one of the clutch harness connector terminals;
• connect the black switch cable wire to the fuse, and from there to 12 VDC power;
• connect the remaining clutch harness connector terminal to ground.
3. Test the switch to ensure that the electric clutch engages and disengages properly.
4. Use electrical tape to seal and secure any electrical connections that might require weather-proofing.
5. Run the electrical cable through the lower frame to prevent accidental disconnection of wiring if the cable is
pulled tight.
6. Secure the cable when not in use.
7
8
6
10
1110
8
9
A224/A225 ELECTRIC CLUTCH KIT – DOUBLE-GROOVE PULLEY
31043 R4 3
Figure 3. Electric Clutch Wiring Diagram
AGI is a leading provider of equipment solutions for agriculture bulk commodities including seed, fertilizer, grain, and feed systems with a growing platform in providing
equipment and solutions for food processing facilities. AGI has manufacturing facilities in Canada, the United States, the United Kingdom, Brazil, South Africa, India and Italy
and distributes its products globally.
P.O. Box 39, Rosenort, Manitoba, R0G 1W0 Canada
P866.467.7207 (Canada & USA) or 204.746.2396 │ F866.768.4852 │ E[email protected]
AGGROWTH.COM aggrowthintl
©Ag Growth International Inc. 2021 │ Printed in Canada
A224/A225 ELECTRIC CLUTCH KIT – DOUBLE-GROOVE PULLEY
/