Kichler Lighting 52282NI User manual

Brand: Kichler Lighting

Model: 52282NI

Type: User manual

Kichler Lighting 52282NI is a versatile lighting fixture that offers multiple mounting options for customized illumination in various spaces. Its rigid stem mount allows for adjustable height, while the loop/chain link mount provides a unique and decorative touch. The semi-flush mount option creates a sleek and modern look, making it suitable for both residential and commercial applications. With its durable construction and easy installation process, the Kichler Lighting 52282NI is an ideal choice for enhancing the ambiance of any room.

IS-52282-US

We’re here to help 866-558-5706

Hrs: M-F 9am to 5pm EST

11) Make wire connecon. Reference chart below for correct

connecons and wire accordingly.

Connect Black or Red

Supply Wire to:

Connect White Supply

Wire to:

Black White

*Parallel cord (round &

smooth)

*Parallel cord (square &

ridged)

Clear, Brown, Gold or

Black without Tracer

Clear, Brown, Gold or Black

with Tracer

Insulated wire (other

than green) with copper

conductor

Insulated wire (other

than green) with silver

conductor

*Note: When parallel wire (SPT

1 & SPT 2) are used. The neutral

wire is square shaped or ridged

and the other wire will be round

in shape or smooth

(see illus.)

Neutral Wire

12) Raise xture to ceiling, carefully passing mounng screws

through holes in canopy[G]. NOTE: Be certain wires do

not get pinched between canopy and ceiling.

13) Use knobs[J] and lockwashers[I] to secure canopy.

Tighten to secure.

14) Raise the glass[S] up over the socket[P] unl seated.

15) Thread the socket ring[R] onto the socket up to the glass

to secure the glass in place.

16) Insert recommended bulbs. (Not supplied).

Fixture Diagram

Parts List

Cauons

CAUTION – RISK OF SHOCK –

Disconnect Power at the main circuit breaker panel or main fusebox before starng and during

the installaon.

WARNING:

This xture is intended for installaon in accordance with the Naonal Electrical Code (NEC) and all

local code specicaons. If you are not familiar with code requirements, installaon by a cered

electrician is recommended.

CLEANING:

• Always be certain that electric current is turned o before cleaning.

• Only a so damp cloth should be used. Harsh cleaning products may damage the nish.

Installaon Instrucons

[A] Stems

[B] Short Threaded Tubes

[C] Outlet Box

[D] Lockwasher

[E] Hexnut

[F] Mounting Strap

[G] Canopy

[H] Strap Mounting Screws

[I] Lockwashers

[J] Knobs

[K] Second Loop

[L] Chain Link

[M] Mounting Screws

[N] Main Body

[O] First Loop

[P] Socket

[Q] 3-inch Tube

[R] Socket Ring

[S] Glass

RIGID STEM MOUNT

1) Pass xture wires from main body[N] through 3-inch tube[Q] and screw tube onto threads

protruding at top of main body.

2) Pass xture wires through desired number of stems[A] and screw stems together using supplied

short threaded tubes[B].

NOTE: A minimum of one (1) 12-inch stem must be used when mounng xture. Pass xture

wire through remaining stems and screw stems together.

NOTE: Thread locking compound must be applied to all stem threads as noted with symbol (4)

to prevent accidental rotaon of xture during cleaning, relamping, etc.

3) Screw rst stem into top of the 3-inch tube[Q].

4) Pass xture wires from last stem through one short threaded tube[B].

5) Screw short threaded tube into top of last stem.

6) Pass xture wires through hole in canopy[G]. Lower canopy down towards stem. Pass hole in

canopy over end of short threaded tube on top of stem.

7) Pass xture wires through lockwasher[D] and then through hexnut[E]. Place lockwasher onto

end of short threaded tube protruding from inside canopy and thread hexnut onto tube.

NOTE: Fixture wires should not be cut shorter than 20 inches from above the canopy.

8) Find the appropriate threaded holes on mounng strap[F]. Assemble mounng screws[M] into

threaded holes.

9) Aach mounng strap to outlet box[C] using the strap mounng screws[H]. Mounng strap

can be adjusted to suit posion of xture.

10) Grounding instrucons: (See Illus. a or b).

a) On xtures where mounng strap is provided with a hole and two raised dimples, wrap

ground wire from outlet box around green ground screw, and thread into hole.

b) On xtures where a cupped washer is provided,aach ground wire from outlet box under

cupped washer and green ground screw, then thread into mounng strap.

If xture is provided with ground wire, connect xture ground wire to outlet box ground wire

with wire connector aer following the above steps. Never connect ground wire to black or

white power supply wires.

GREEN GROUND

SCREW

CUPPED

WASHER

OUTLET BOX

GROUND

FIXTURE

GROUND

DIMPLES

WIRE CONNECTOR

OUTLET BOX

GROUND

GREEN GROUND

SCREW

FIXTURE

GROUND

Installaon Instrucons (connued)

LOOP / CHAIN LINK MOUNT

1) Follow steps 1 - 3 from “Rigid Stem Mount” Instrucons.

2) Pass xture wires from last stem through short threaded

tube[B] and through rst loop[O]. Screw short threaded

tube into top of last stem and into rst loop.

3) Pass xture wires through second loop[K], short threaded

tube, and hole in canopy[G]. Screw short threaded tube into

end of second loop.

4) (If second loop is already aached to canopy, proceed to

next step). Insert short threaded tube at end of second loop

through hole in canopy. Thread lock washer[D] onto short

threaded tube protruding from inside canopy. Pass xture

wires through hexnut[E] and thread hexnut onto end of

short threaded tube.

NOTE: Fixture wires should not be cut shorter than 20

inches from above the canopy.

5) Aach open chain link[L] to loop at end of stem(s) and to

loop on canopy. Once aached, close the open chain link by

placing a piece of cloth over the open link and using a pair of

pliers to gently squeeze the link closed.

6) Follow steps 8 - 16 from “Rigid Stem Mount” Instrucons.

SEMI-FLUSH MOUNT

1) Pass xture wires from main body[N] through 3-inch

tube[Q] and screw tube onto threads protruding at top of

main body.

2) Pass xture wires through one short threaded tube[B] and

through hole in center of canopy[G].

3) Screw short threaded tube into top of the 3-inch tube.

4) Slip canopy over exposed threads of short threaded tube

connected to 3-inch tube, making sure the tube passes

through hole in center of canopy.

5) Follow steps 7 - 16 from “Rigid Stem Mount” Instrucons.

SEMI-FLUSH MOUNTRIGID STEM MOUNT LOOP / CHAIN LINK

MOUNT

►

P P

Page is loading ...

Kichler Lighting 52282NI User manual

Brand: Kichler Lighting

Model: 52282NI

Type: User manual

Download PDF

report

in other languages

français: Kichler Lighting 52282NI Manuel utilisateur
español: Kichler Lighting 52282NI Manual de usuario

Kichler Lighting 52282NI User manual

Kichler Lighting 52282NI User manual

in other languages

Related papers

Other documents