Kichler Lighting 52073BK offers versatile mounting options for your desired placement, whether it's a rigid stem mount for a classic look or a loop/chain link mount for a more dynamic effect. With its adjustable canopy, you can customize the fixture's position to suit your space perfectly.
Kichler Lighting 52073BK offers versatile mounting options for your desired placement, whether it's a rigid stem mount for a classic look or a loop/chain link mount for a more dynamic effect. With its adjustable canopy, you can customize the fixture's position to suit your space perfectly.
IS-52073-US
We’re here to help 866-558-5706
Hrs: M-F 9am to 5pm EST
12) Pass xture wires through lockwasher[D] and then through hexnut[E]. Place
lockwasher onto end of short threaded tube protruding from inside canopy
and thread hexnut onto tube.
NOTE: Fixture wires should not be cut shorter than 20 inches from above the
canopy.
13) Find the appropriate threaded holes on mounng strap[F]. Assemble
mounng screws[M] into threaded holes.
14) Aach mounng strap to outlet box[C] using the strap mounng screws[H].
Mounng strap can be adjusted to suit posion of xture.
15) Grounding instrucons: (See Illus. a or b).
a) On xtures where mounng strap is provided with a hole and two raised
dimples, wrap ground wire from outlet box around green ground screw,
and thread into hole.
b) On xtures where a cupped washer is provided,aach ground wire from
outlet box under cupped washer and green ground screw, then thread
into mounng strap.
If xture is provided with ground wire, connect xture ground wire to outlet
box ground wire with wire connector aer following the above steps. Never
connect ground wire to black or white power supply wires.
16) Make wire connecons. Reference chart below for correct connecons and
wire accordingly.
Connect Black or Red
Supply Wire to:
Connect White Supply
Wire to:
Black White
*Parallel cord (round &
smooth)
*Parallel cord (square &
ridged)
Clear, Brown, Gold or
Black without Tracer
Clear, Brown, Gold or Black
with Tracer
Insulated wire (other
than green) with copper
conductor
Insulated wire (other
than green) with silver
conductor
*Note: When parallel wire (SPT
1 & SPT 2) are used. The neutral
wire is square shaped or ridged
and the other wire will be round
in shape or smooth
(see illus.)
Neutral Wire
17) Push xture to ceiling, carefully passing mounng screws through holes in
canopy[G]. NOTE: Be certain wires do not get pinched between mounng
strap and canopy, or canopy and ceiling.
18) Use knobs[J] and lockwashers[I] to secure canopy. Tighten to secure.
19) Insert recommended bulbs. (Not supplied).
GREEN GROUND
SCREW
CUPPED
WASHER
OUTLET BOX
GROUND
FIXTURE
GROUND
DIMPLES
WIRE CONNECTOR
OUTLET BOX
GROUND
GREEN GROUND
SCREW
FIXTURE
GROUND
a
b
Fixture Diagram
Parts List
Cauons
CAUTION – RISK OF SHOCK –
Disconnect Power at the main circuit breaker panel or main fusebox before
starng and during the installaon.
WARNING:
This xture is intended for installaon in accordance with the Naonal Electrical
Code (NEC) and all local code specicaons. If you are not familiar with code
requirements, installaon by a cered electrician is recommended.
CLEANING:
• Always be certain that electric current is turned o before cleaning.
• Only a so damp cloth should be used. Harsh cleaning products may damage
the nish.
Installaon Instrucons
[A] Stems
[B] Short Threaded
Tubes
[C] Outlet Box
[D] Lockwasher
[E] Hexnut
[F] Mounting Strap
[G] Canopy
[H] Strap Mounting
Screws
[I] Lockwashers
[J] Knobs
[K] Second Loop
[L] Chain Link
[M] Mounting Screws
[N] Shade Assembly
[O] First Loop
[P] Center Tube
[Q] Glass
[R] Rubber Washer
[S] Steel Washer
[T] Hexnut
[U] Finial
RIGID STEM MOUNT
1) Screw center tube[P] into coupling inside shade assembly[N].
2) Li glass[Q] into boom of shade assembly, making sure the threads on the
boom of center tube[P] pass through center hole of glass.
3) Place rubber washer[R] over threads of center tube protruding through hole
in glass.
4) Place steel washer[S] over threads of center tube protruding through rubber
washer.
5) Screw hexnut[T] onto threads of center tube protruding through steel
washer and ghten to secure washers and glass.
6) Screw nial[U] onto threads of center tube protruding through hexnut and
ghten to cover hexnut.
7) Pass xture wires through desired number of stems[A] and screw stems
together using supplied short threaded tubes[B].
NOTE: Thread locking compound must be applied to all stem threads as
noted with symbol (4) to prevent accidental rotaon of xture during
cleaning, relamping, etc.
8) Screw rst stem into coupling aached to top of shade assembly[N].
9) Pass xture wires from last stem through one short threaded tube[B].
10) Screw short threaded tube into top of last stem.
11) Pass xture wires through hole in canopy[G]. Lower canopy down towards
stem. Pass hole in canopy over end of short threaded tube on top of stem.
Installaon Instrucons (connued)
LOOP / CHAIN LINK MOUNT
1) Follow steps 1 - 8 from “Rigid Stem Mount” Instrucons.
2) Pass xture wires from last stem through short threaded tube[B] and through
rst loop[O]. Screw short threaded tube into top of last stem and into rst loop.
3) Pass xture wires through second loop[K], short threaded tube, and hole in
canopy[G]. Screw short threaded tube into end of second loop.
4) (If second loop is already aached to canopy, proceed to next step). Insert
short threaded tube at end of second loop through hole in canopy. Thread lock
washer[D] onto short threaded tube protruding from inside canopy. Pass xture
wires through hexnut[E] and thread hexnut onto end of short threaded tube.
NOTE: Fixture wires should not be cut shorter than 20 inches from above the
canopy.
5) Aach open chain link[L] to loop at end of stem(s) and to loop on canopy. Once
aached, close the open chain link by placing a piece of cloth over the open link
and using a pair of pliers to gently squeeze the link closed.
6) Follow steps 13 - 19 from “Rigid Stem Mount” Instrucons.
F
H
M
G
I
J
B
K
O
L
A
N
P
Q
R
S
T
U
E
D
C
Page is loading ...
Page is loading ...
-
1
-
2
-
3
Kichler Lighting 52073BK offers versatile mounting options for your desired placement, whether it's a rigid stem mount for a classic look or a loop/chain link mount for a more dynamic effect. With its adjustable canopy, you can customize the fixture's position to suit your space perfectly.
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
in other languages
Related papers
-
Kichler Lighting 52282NI User manual
-
Kichler Lighting 49309BK User manual
-
Kichler Lighting 52141BK User manual
-
Kichler Lighting 52263OZ User manual
-
Kichler Lighting 52092AUB User manual
-
Kichler Lighting 52072BK User manual
-
Kichler Lighting 52035ACO User manual
-
Kichler Lighting 52093AUB User manual
-
Kichler Lighting 52039CLP User manual
-
Kichler Lighting 52233BK User manual
Other documents
-
Kichler 44046AUB Installation guide
-
OK LIGHTING OK-5117H Installation guide
-
-
-
-
-
-
-
OK LIGHTING OK-5119-H1 Installation guide
-
