Serene S2077 Installation guide

Type
Installation guide

Serene S2077

The Serene S2077 is a bathroom fan heater designed to provide warmth and ventilation in your bathroom.

Serene S2077

The Serene S2077 is a bathroom fan heater designed to provide warmth and ventilation in your bathroom.

S2077
Serene Bathroom Fan Heater
Installation and Operating Manual
PRN5987 Rev. 3.0 March 2012
2
S2077
Serene Bathroom Fan Heater
Safety Information
When using any electrical appliance, safety precautions should always
be observed. Read these instructions carefully, and retain for future
reference. For service, contact your nearest authorised service agent.
When used by, or near, young children or infirm persons, close
supervision is necessary. Young children should be supervised to
ensure that they do not play with the appliance.
•Do NOT use this appliance other than for its intended use.
•Do NOT cover the grilles or place any object or material up against
the unit, as this may block entry or exhaust airflow.
•Do NOT probe any opening to remove fluff.
•Do NOT allow the supply cord to come into contact with heated
surfaces during operation.
Use this appliance with the voltage specified on the rating label.
Be very careful not to touch hot surfaces or moving parts.
If the supply cord becomes damaged, it must be replaced by a
SKOPE authorised service agent, or similarly qualified person, in
order to avoid a hazard.
Regulations require that electrical work be carried out by
authorised persons. For your own safety and that of others, ensure
this is done.
Operation
The operation of the heater is controlled by use of the pull-cord switch.
Pull the pull-cord to switch the heater on. Pull the pull-cord again to
switch the heater off. The red LED indicator lights when the heater is
operating.
The heat output is regulated by an internal step-down thermostat,
which will reduce the output from 2000-2400 Watts to 1000-1200
Watts, when a comfortable room temperature is reached.
3
S2077
Serene Bathroom Fan Heater
Installation
This appliance MUST be installed in accordance with relevant wiring
rules and regulations which cover installation of appliances and
accessories in damp situations such as bathrooms, showers, laundries
and other areas with fixed water containers (in Australia and New
Zealand - AS/NZS 3000:2007 Wiring Rules).
To attach the heater to the wall:
1. Remove the wall mounting base from the heater by using a
screwdriver (with a large flat blade) to release both side clips from
inside the base.
2. Secure the mounting base to the wall using the four fixing screw
holes provided. The base supplied with the heater must be used
when attaching the heater to the wall. See diagram above for
installation distances.
3. Locate the heater onto the mounting base and snap into position.
4. Connect the flexible cord to the mains power supply. A suitable
disconnection device (acting in all active supplies) is required to
be incorporated in the fixed supply wiring.
Distances
The heater must be mounted a
minimum distance of:
1800mm from floor level
200mmm below the ceiling
250mm from adjacent walls
500mm between the heater and
any objects heated below it.
IMPORTANT:
The heater must NOT be located
immediately below a socket outlet
or within reach of a bath or shower.
Figure 1:
Installation Distances
4
S2077
Serene Bathroom Fan Heater
Specifications
SKOPE Industries Limited reserve the right to alter specifications without notice.
Cleaning
The heater requires regular cleaning to ensure trouble free operation.
1. Isolate the heater from the mains power supply.
2. Use a damp cloth to clean the exterior of the heater. Do NOT use
any abrasive cleaners.
3. Use a vacuum cleaner to remove dust and fluff from the heater
inlet and outlet grilles.
4. Ensure the heater is dry before turning the mains power supply to
the heater back on
Contact Addresses
New Zealand
SKOPE INDUSTRIES LIMITED
PO Box 1091
Christchurch
New Zealand
Freephone: 0800 947 5673
Fax: (03) 983 3896
Email: enquir[email protected]
Website: www.skope.co.nz
Dimensions
Height: 220mm
Width: 375mm
Depth: 140mm (includes mounting base)
Weight: 2.35 kg
Electrical
Wattage: 2000-2400 Watts, thermostatically reduced to 1000-1200 Watts
Supply: 220-240 Volts a.c. 50/60 Hz.
Wiring: Permanent connection. Double Insulated, no Earth required.
Ingress Protection Rating: IP20
Australia
A.B.N. 73 374 418 306
PO Box 7543
Baulkham Hills B.C.
NSW 2153, Australia
Freephone: 1800 121 535
Freefax: 1800 121 533
Website: www.skope.com.au
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4

Serene S2077 Installation guide

Type
Installation guide

Serene S2077

The Serene S2077 is a bathroom fan heater designed to provide warmth and ventilation in your bathroom.

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI