Canopy
Appropriate fasteners
(by others)
(x2)
Mounting plate
1.
To mount non-power side pendant, use dimensions provided
on page three(3).
2.
Using appropriate fasteners(by others), secure mounting plate
to structure/ bracing in ceiling.
End cap
#8-32 x.75"
Cap screw
(x2)
1/4-20 x1"
Aiming screw
3/8-16 x1"
Hex end screw
(x2)
Fixture door
Mounting bracket
Canopy
Exploded View and Part Call-Out
J-box
(by others)
Securing Power side Pendant to Ceiling
Attention:
All extra large fixtures require additional bracing/structure around J-box to support fixture.
Securing non-Power side Pendant
Pendant length dependant
on order(multiple sections
may be required, consult
factory for coupler and
safety wire installation
requirements).
Appropriate fasteners
(by others)
(x2)
Canopy
J-box
(by others)
Mounting plate
1.
Remove canopy and allow it slide down pendant.
2.
Using appropriate fasteners(by others), secure mounting
plate to structure/ bracing around J-box.
3.
For mounting plate dimensions refer to page three(3).
Warning
: Before starting any work ensure
that all sources of power are turned off. All
work must meet local/national codes and be
performed by a certified electrician.
Do not
mount fixtures vertically.
Installation Instructions
1.
Sheet 1 of 3
Roundel, XL
INDOOR
PS
(Pendant Swivel)
Visor and Non-Visor
2.
ADY080864 REV B(ECN080377)
Warning
: Before starting any work ensure
that all sources of power are turned off. All
work must meet local/national codes and be
performed by a certified electrician.
Do not
mount fixtures vertically.
Installation Instructions
3. 4.
Sheet 2 of 3
5.
Roundel, XL
INDOOR
PS
(Pendant Swivel)
Visor and Non-Visor
ADY080864 REV B(ECN080377)
#8-32 x.75"
End Screw
(x2)
1/4"-20 safety wire
connector
(x2)
1.
After hanging both pendants, carefully lift fixture head into
place.
2.
Secure fixture using both 3/8 -16 x 1" End screws.
3.
Secure desired angle using 1/4-20 x 1" Aiming screws.
Wiring the Fixture
3/8-16 x1"
End Screw
(x2)
1/4-20 x1"
Aiming Screw
(x2)
Fixture wire
End Cap
1.
To secure safety wire to fixture, screw 1/4"-20 wire connector to bottom of pendant bracket.
2.
Run safety wire up pendant tube and secure to structure in ceiling.
3.
To adjust angle of fixture head, loosen both 1/4-20 x1" aiming screws.
4.
Rotate fixture head to desired angle and secure with both 1/4-20 x1" aiming screws.
5.
Replace end cap using 8-32 x.75" end screw.
J-box hidden
for clarity
1.
After securing the fixture head to the pendants, run fixture wire
up pendant tube to J-box.
2.
Attach appropriate wires ensuring all connections are properly
matched.
3.
Secure canopy to mounting plate.
Canopy
Fixture wire
Securing Safety Wires and Aiming the Fixture
Mounting Fixture to Pendants
Side view
40
Top View
Mounting Plate Dimensions
In[mm]
Lamping Size Chart
(lamps provided by others)
744.07
29
9
32
"5"
127
Side View
7
"
16
2"
62.08
4
3
19.05
4.86
3
"
16
1
31
32
"
49.92
15
49.43
16
1 "
36.95
"1
32
15
5
1
32
"
127.84
Warning
: Before starting any work ensure
that all sources of power are turned off. All
work must meet local/national codes and be
performed by a certified electrician.
Do not
mount fixtures vertically.
Installation Instructions
Sheet 3 of 3
Roundel, XL
INDOOR
PS
(Pendant Swivel)
Visor and Non-Visor
ADY080864 REV B(ECN080377)
FIXTURE SIZE
(inches/ mm )
WATTAGE
# OF
LAMPS
LAMP TYPE LAMP DESCRIPTION
LAMP
(not to scale)
27/ 685.8 250W 1 ED28 Metal Halide
27/ 685.8 400W 1 ED28/BT37 Metal Halide
27/ 685.8 400W 2 ED28/BT37 Metal Halide
27/ 685.8 750W 1 BT37 Metal Halide
27/ 685.8 1000W 1 BT37 Metal Halide
-
1
-
2
-
3
Ametrix PS User manual
- Type
- User manual
- This manual is also suitable for
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
Other documents
-
Cooper Lighting M2N-E SLI User manual
-
-
-
-
-
-
-
-
-